User Manual pt. 5

JETI model s.r.o. DS24V2US Transmitter Duplex 2A7CJ-DS24V2US 2A7CJDS24V2US ds24v2us

User Manual for duplex models including: 2A7CJ-DS24V2US, 2A7CJDS24V2US, ds24v2us, DS24V2US Radio Control System, DS24V2US, Radio Control System, Control System, System

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 6 Pages, 5.73MB

Document DEVICE REPORTGetApplicationAttachment.html?id=8366524 
radio control system
6.1.5 Setting the Range of the gimbal
At the transmitter, it is possible to define the range of motion for the gimbal. 1. Place the magnetic key (a) on the cover ring (b) of the gimbal and
remove it from position (c).
Fig. 6.20
(a) (a)

EN
2. Setting the Upper Motion Limit of the Throttle stick:
Insert the "allen key" into screw ,,E". Turning the screw counterclockwise increases the range of motion (see Fig. 6.22). Turning the screw clockwise decreases the range of motion (see Fig. 6.22).
Fig. 6.22

E

-+ -+

Fig. 6.21

(b)
Left

E
Right

Note: When fully loosened, the head of the screw (a) must not be higher than the seating surface of the cover ring (b) (Fig. 6.15).

Note: It is recommended to determine the desired position of the

(c)

stop (end of travel) by gradually moving in the adjusted axis (during the adjustment).

Fig. 6.19
59

radio control system
Caution: Tighten the screws with care to avoid damaging the gimbal.
3. Setting the Downward Movement Limit of the Throttle stick: Insert the "allen key" into screw,,A" . Turning the screw counterclockwise increases the range of motion (see Fig. 6.23). Turning the screw clockwise decreases the range of motion (see Fig. 6.23).
Note: When fully loosened, the head of the screw (a) must not be higher than the seating surface of the cover ring (b) (Fig. 6.15).
Note: It is recommended to determine the desired position of the stop (end of travel) by gradually moving in the adjusted axis (during the adjustment).
Obr. 6.23

EN
Caution: T ighten the screws with care to avoid damaging the gimbal.
4. Place the cover ring back onto the gimbal so that its groove (e) fits precisely over the locking pin (d) (in the area of adjustment screw ",,D") on the gimbal. Visually, the ring should lie in line with the front side of the transmitter. ).
Obr. 6.24
(d)
(e)

Left

-+ -+

A A

5. Turn on the transmitter and in the "menu/system/input display," press the "F1" button ("Calib") and perform a new calibration of the throttle stick and its range.
Right
60

radio control system

6.1.6 Changing the Transmitter Mode from 1 (3) to 2 (4)

The transmitter is equipped with universal gimbals. Both gimbals are identical, and by adjusting them, the transmitter can be set to modes 1 through 4. After the mechanical adjustment, it is necessary to set the specific mode of the transmitter in the "menu/system/configuration -> Mode 1-4."

1. P l a c e t h e magnetic key (a)

Fig. 6.26

on the cover ring

(a)

(b) of the gimbal

and remove it

from position (c).

(b) (a)

Fig. 6.27

EN

2. Deactivating the Throttle Stick and Setting the Center Position with Spring Centering: Loosen screws ,,F" and ,,G" by turning them counterclockwise to the maximum, so that no locking (braking) occurs.

Fig. 6.28

Fig. 6.29

G

F-

Right

-

Right

Loosen screw ,,C" by turning it counterclockwise to the maximum, which will gradually activate the center return spring. You can adjust the strength of the return spring using the adjustment screw ,,D".

Fig. 6.25

(c) 61

C
Right
Fig. 6.30

D
R+-ight
Fig. 6.31

radio control system

3. Activation of the throttle stick with locking (brake) adjustment and limitation of centering using a spring: Use the screw to reduce the strength of the return spring ,,D" (to avoid unnecessary tension). Tighten screw ,,C" by turning it clockwise to the maximum, which will gradually deactivate the center return spring.

Fig. 6.32

Fig. 6.33

D -

C

Left

Left

By tightening screws ,,F" (ratchet) and ,,G" (smooth) clockwise, adjust the locking force (brake) of the throttle stick.

Fig. 6.34

Fig. 6.35

EN

Caution: Tighten the screws with care to avoid damaging the gimbal.

Note: When fully loosened, the

head of the screw (a) must not be

higher than the seating surface of (a)

(b)

the cover ring (b)

4. Place the cover ring back onto the gimbal so that its groove (e) fits precisely over the locking pin (d) (in the area of adjustment screw ",,D") on the gimbal. Visually, the ring should lie in line with the front side of the transmitter ).

(d)

Obr. 6.36

(e)

F

Left

Left

G
5. Turn on the transmitter and in the "menu/system/input display," press the "F1" button ("Calib") and perform a new calibration of the throttle stick and its range.
62

radio control system

6.1.7 Changing the Transmitter Mode from 2 (4) to 1 (3)

The transmitter is equipped with universal gimbals. Both gimbals are identical, and by adjusting them, the transmitter can be set to modes 1 through 4. After the mechanical adjustment, it is necessary to set the specific mode of the transmitter in the "menu/system/configuration -> Mode 1-4."

1. P l a c e t h e Fig. 6.38 magnetic key (a)

on the cover ring

(a)

(b) of the gimbal

and remove it

from position (c).

(a)

(b)

Fig. 6.39

EN
2. Deactivating the Throttle Stick and Setting the Center Position with Spring Centering: Loosen screws ,,F" and ,,G" by turning them counterclockwise to the maximum, so that no locking (braking) occurs.

Fig. 6.40

Fig. 6.41

-

F

G -

Left

Left

Loosen screw ,,C" by turning it counterclockwise to the maximum, which will gradually activate the center return spring. You can adjust the strength of the return spring using the adjustment screw ,,D".

Fig. 6.42

Fig. 6.43

Fig. 6.37

(c)

C

Left

63

D +-
Left

radio control system
3. Activation of the throttle stick with locking (brake) adjustment and limitation of centering using a spring: Use the screw to reduce the strength of the return spring ,,D" (to avoid unnecessary tension). Tighten screw ,,C" by turning it clockwise to the maximum, which will gradually deactivate the center return spring.
Fig. 6.44

C

D -

Right

Fig. 6.45 Right

By tightening screws ,,F" (ratchet) and ,,G" (smooth) clockwise,

adjust the locking force (brake) of the throttle stick.

Right

Right

EN

Caution: Tighten the screws with care to avoid damaging the gimbal

Note: When fully loosened, the

head of the screw (a) must not be

higher than the seating surface of (a)

(b)

the cover ring (b)

4. Place the cover ring back onto the gimbal so that its groove (e) fits precisely over the locking pin (d) (in the area of adjustment screw ",,D") on the gimbal. Visually, the ring should lie in line with the front side of the transmitter ).

(d)

Fig. 6.48

(e)

F Fig. 6.46

G Fig. 6.47

5. Turn on the transmitter and in the "menu/system/input display," press the "F1" button ("Calib") and perform a new calibration of the throttle stick and its range.
64

References

Related FCC IDs:

Search Any Device: