2412RSU039-U4-FCC NII Test Report
Dell
Test Report NII Part 1
HAN Networks Co., Ltd. AP52X HAN Access Point 2ALJ3AP52X 2ALJ3AP52X ap52x
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 57 Pages, 5.53MB
Document DEVICE REPORTGetApplicationAttachment.html?id=7988718MRT Technology (Suzhou) Co., Ltd Phone: +86-512-66308358 Web: www.mrt-cert.com Report No.: 2412RSU039-U4 Report Version: V01 Issue Date: 2024-12-31 RF MEASUREMENT REPORT FCC ID: 2ALJ3AP52X Applicant: HAN Networks Co., Ltd. Product: HAN Access Point Model No.: AP521 Brand Name: HAN NETWORKS, HANNETWORKS FCC Classification: Unlicensed National Information Infrastructure (NII) FCC Rule Part(s): Part 15 Subpart E (Section 15.407) Result: Complies Received Date: 2024-08-12 Test Date: 2024-09-01 ~ 2024-10-17 Reviewed By: Approved By: Vincent Yu Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB789033. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Template Version:1.5 1 of 495 Report No. 2412RSU039-U4 Version V01 Revision History Description Initial Report Report No.: 2412RSU039-U4 Issue Date 2024-12-31 Note Valid Note: This report is a copy report based on MRT original report (Report No.: 2408RSU020-U4). Only applicant & manufacture information and product information (name, model and brand name) has changed in this report. 2 of 495 Report No.: 2412RSU039-U4 CONTENTS Description Page 1. General Information ................................................................................................................................6 1.1. Applicant ..................................................................................................................................... 6 1.2. Manufacturer............................................................................................................................... 6 1.3. Testing Facility ............................................................................................................................ 6 1.4. Product Information .................................................................................................................... 7 1.5. Radio Specification under Test ................................................................................................... 8 1.6. Working Frequencies.................................................................................................................. 9 1.7. Antenna Details ........................................................................................................................ 10 2. Test Configuration ................................................................................................................................. 11 2.1. Test Mode ..................................................................................................................................11 2.2. Test System Connection Diagram ............................................................................................ 12 2.3. Test Software ............................................................................................................................ 12 2.4. Applied Standards .................................................................................................................... 13 2.5. Test Environment Condition...................................................................................................... 13 3. Antenna Requirements .........................................................................................................................14 4. Measuring Instrument ...........................................................................................................................15 5. Decision Rules and Measurement Uncertainty ..................................................................................17 5.1. Decision Rules.......................................................................................................................... 17 5.2. Measurement Uncertainty ........................................................................................................ 17 6. Test Result..............................................................................................................................................18 6.1. 6.2. 6.2.1. 6.2.2. 6.2.3. 6.2.4. 6.2.5. 6.3. 6.3.1. 6.3.2. 6.3.3. 6.3.4. 6.3.5. 6.4. 6.4.1. Summary .................................................................................................................................. 18 26dB & 99% Bandwidth Measurement..................................................................................... 19 Test Limit................................................................................................................................... 19 Test Procedure ......................................................................................................................... 19 Test Setting ............................................................................................................................... 19 Test Setup................................................................................................................................. 19 Test Result ................................................................................................................................ 20 6dB Bandwidth Measurement .................................................................................................. 21 Test Limit................................................................................................................................... 21 Test Procedure ......................................................................................................................... 21 Test Setting ............................................................................................................................... 21 Test Setup................................................................................................................................. 21 Test Result ................................................................................................................................ 21 Output Power Measurement..................................................................................................... 22 Test Limit................................................................................................................................... 22 3 of 495 Report No.: 2412RSU039-U4 6.4.2. Test Procedure ......................................................................................................................... 22 6.4.3. Test Setting ............................................................................................................................... 22 6.4.4. Test Setup................................................................................................................................. 22 6.4.5. Test Result ................................................................................................................................ 22 6.5. Transmit Power Control Measurement ..................................................................................... 23 6.5.1. Test Limit................................................................................................................................... 23 6.5.2. Test Procedure ......................................................................................................................... 23 6.5.3. Test Setting ............................................................................................................................... 23 6.5.4. Test Setup................................................................................................................................. 23 6.5.5. Test Result ................................................................................................................................ 23 6.6. Power Spectral Density Measurement ..................................................................................... 24 6.6.1. Test Limit................................................................................................................................... 24 6.6.2. Test Procedure ......................................................................................................................... 24 6.6.3. Test Setting ............................................................................................................................... 24 6.6.4. Test Setup................................................................................................................................. 25 6.6.5. Test Result ................................................................................................................................ 25 6.7. Frequency Stability Measurement ............................................................................................ 26 6.7.1. Test Limit................................................................................................................................... 26 6.7.2. Test Procedure ......................................................................................................................... 26 6.7.3. Test Setup................................................................................................................................. 26 6.7.4. Test Result ................................................................................................................................ 27 6.8. Radiated Spurious Emission Measurement ............................................................................. 28 6.8.1. Test Limit................................................................................................................................... 28 6.8.2. Test Procedure ......................................................................................................................... 28 6.8.3. Test Setting ............................................................................................................................... 28 6.8.4. Test Setup................................................................................................................................. 30 6.8.5. Test Result ................................................................................................................................ 31 6.9. Radiated Restricted Band Edge Measurement ........................................................................ 32 6.9.1. Test Limit................................................................................................................................... 32 6.9.2. Test Procedure ......................................................................................................................... 34 6.9.3. Test Setting ............................................................................................................................... 34 6.9.4. Test Setup................................................................................................................................. 35 6.9.5. Test Result ................................................................................................................................ 35 6.10. AC Conducted Emissions Measurement.................................................................................. 36 6.10.1. Test Limit................................................................................................................................... 36 6.10.2. Test Setup................................................................................................................................. 36 6.10.3. Test Result ................................................................................................................................ 36 Appendix A Test Result............................................................................................................................37 A.1 Duty Cycle Test Result ............................................................................................................... 37 4 of 495 Report No.: 2412RSU039-U4 A.2 26dB Bandwidth Test Result ...................................................................................................... 40 A.3 6dB Bandwidth Test Result ........................................................................................................ 71 A.4 Output Power Test Result .......................................................................................................... 79 A.5 Power Spectral Density Test Result ........................................................................................... 83 A.6 Frequency Stability Test Result................................................................................................ 183 A.7 Radiated Spurious Emission Test Result ................................................................................. 184 A.8 Radiated Restricted Band Edge Test Result............................................................................ 292 A.9 AC Conducted Emissions Test Result ..................................................................................... 490 Appendix B Test Setup Photograph .....................................................................................................494 Appendix C EUT Photograph ................................................................................................................495 5 of 495 Report No.: 2412RSU039-U4 1. General Information 1.1. Applicant HAN Networks Co., Ltd. 101-A16, 1st Floor, Building 3, No.9 compound, Yongfeng Road, Haidian District, Beijing, P.R. China 1.2. Manufacturer HAN Networks Co., Ltd. 101-A16, 1st Floor, Building 3, No.9 compound, Yongfeng Road, Haidian District, Beijing, P.R. China 1.3. Testing Facility Test Site MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Location (Suzhou - Wujiang) Building 1, No.1 Xingdong Road, Wujiang, Suzhou, Jiangsu, People's Republic of China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 VCCI: R-20025 R-20141 G-20034 G-20134 C-20020 C-20103 T-20020 T-20104 Test Site MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 CNAS: L10551 FCC: CN1284 ISED: CN0105 Test Site MRT Taiwan Laboratory Laboratory Location (Taiwan) No. 38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Laboratory Accreditations TAF: 3261 FCC: 291082, TW3261 ISED: TW3261 6 of 495 Report No.: 2412RSU039-U4 1.4. Product Information Product Name HAN Access Point Model No. AP521 EUT Identification No. 20240929Sample#06 20240819Sample#16 Wi-Fi Specification 802.11a/b/g/n/ac/ax/be Bluetooth Specification V5.1 single mode, BLE only Zigbee Specification 802.15.4 Antenna Information Refer to section 1.7 Power Type AC/DC Adapter Input or PoE Input Operating Environment Indoor Use Accessories Model: ADP-50GR B Adapter Input: 100-240V ~ 1.3A 50-60Hz Output: 48.0V, 1.042A 50.1W Model: POE60U-1BT-X (ALE P/N: POE60U-1BT-X-R) Input: 100-240V ~ 1.5A, 50/60Hz Output: 56.0V, 0.535A, 30W PoE Injector PIN 3, 6+ PIN 1, 2 Return Output: 56.0V, 0.535A, 30W PIN 4, 5+ PIN 7, 8 Return Remark: 1. The information of EUT was provided by the manufacturer, and the accuracy of the information shall be the responsibility of the manufacturer. 2. AC/DC Power Adapter and PoE Injector are not sold with Product. For this report, we select AC/DC Adapter for testing. 7 of 495 Report No.: 2412RSU039-U4 1.5. Radio Specification under Test Frequency Range For 802.11a/n-HT20/ac-VHT20/ax-HE20/be-EHT20: 5180~5240MHz, 5260~5320MHz, 5500~5720MHz, 5745~5825MHz For 802.11n-HT40/ac-VHT40/ax-HE40/be-EHT40: 5190~5230MHz, 5270~5310MHz, 5510~5710MHz, 5755~5795MHz For 802.11ac-VHT80/ax-HE80/be-EHT80: 5210MHz, 5290MHz, 5530MHz, 5610 MHz, 5690MHz, 5775MHz For 802.11ac-VHT160/ax-HE160/be-EHT160: 5250MHz, 5570MHz Type of Modulation 802.11a/n/ac: OFDM 802.11ax/be: OFDMA Data Rate 802.11a: 6/9/12/18/24/36/48/54Mbps 802.11n: up to 600Mbps 802.11ac: up to 3467Mbps 802.11ax: up to 4804Mbps 802.11be: up to 5764Mbps Channel Puncturing Function Supported Unsupported Support RU Full RU Partial RU 8 of 495 1.6. Working Frequencies 802.11a/n-HT20/ac-VHT20/ax-HE20/be-EHT20 Channel Frequency Channel 36 5180 MHz 40 48 5240 MHz 52 60 5300 MHz 64 104 5520 MHz 108 116 5580 MHz 120 128 5640 MHz 132 140 5700 MHz 144 153 5765 MHz 157 165 5825 MHz -- 802.11n-HT40/ac-VHT40/ax-HE40/be-EHT40 Channel Frequency Channel 38 5190 MHz 46 62 5310 MHz 102 118 5590 MHz 126 142 5710 MHz 151 802.11ac-VHT80/ax-HE80/be-EHT80 Channel Frequency 42 5210 MHz 122 5610 MHz Channel 58 138 802.11ac-VHT160/ax-HE160/be-EHT160 Channel Frequency Channel 50 5250 MHz 114 Frequency 5200 MHz 5260 MHz 5320 MHz 5540 MHz 5600 MHz 5660 MHz 5720 MHz 5785 MHz -- Frequency 5230 MHz 5510 MHz 5630 MHz 5755 MHz Frequency 5290 MHz 5690 MHz Frequency 5570 MHz Report No.: 2412RSU039-U4 Channel 44 56 100 112 124 136 149 161 -- Frequency 5220 MHz 5280 MHz 5500 MHz 5560 MHz 5620 MHz 5680 MHz 5745 MHz 5805 MHz -- Channel 54 110 134 159 Frequency 5270 MHz 5550MHz 5670 MHz 5795 MHz Channel 106 155 Frequency 5530 MHz 5775 MHz Channel -- Frequency -- 9 of 495 Report No.: 2412RSU039-U4 1.7. Antenna Details Antenna Type Wi-Fi Antenna PIFA PIFA & Dipole Frequency (MHz) 2412 ~ 2462 5180 ~ 5825 5925 ~ 7125 TX Paths 2 4 2 Max. Directional Gain (dBi) Correlated Uncorrelated 5.82 2.83 9.12 3.18 4.84 4.84 Notes: 1. The EUT supports Cyclic Delay Diversity (CDD) mode, and CDD signals are correlated. 2. The EUT also supports Beam Forming mode, and the Beam Forming support 802.11n/ac/ax/be, not include 802.11a/b/g. 3. For beamforming operation, the software automatically backs power down based on CDD power. 4. The detail calculation method of directional gain refers to antenna report provided by the applicant. 5. Uncorrelated Directional Gain is for EIRP calculation, and Correlated Directional Gain is for PSD calculation. 10 of 495 Report No.: 2412RSU039-U4 2. Test Configuration 2.1. Test Mode Mode 1: Transmit by 802.11a_NSS=1 (6Mbps) Mode 2: Transmit by 802.11ac-VHT20_NSS=1 (MCS0) Mode 3: Transmit by 802.11ac-VHT40_NSS=1 (MCS0) Mode 4: Transmit by 802.11ac-VHT80_NSS=1 (MCS0) Mode 5: Transmit by 802.11ac-VHT160_NSS=1 (MCS0) Mode 6: Transmit by 802.11ax-HE20_NSS=1 (MCS0) Mode 7: Transmit by 802.11ax-HE40_NSS=1 (MCS0) Mode 8: Transmit by 802.11ax-HE80_NSS=1 (MCS0) Mode 9: Transmit by 802.11ax-HE160_NSS=1 (MCS0) Mode 10: Transmit by 802.11be-EHT20_NSS=1 (MCS0) Mode 11: Transmit by 802.11be-EHT40_NSS=1 (MCS0) Mode 12: Transmit by 802.11be-EHT80_NSS=1 (MCS0) Mode 13: Transmit by 802.11be-EHT160_NSS=1 (MCS0) Notes: 1. The modulation and the data rate picked for testing are determined by the Max. RF conducted power. 2. For CDD mode, this device supports 4 NSS and power level is the same of spatial multiplexing. The worst case is NSS=1. 3. For beamforming operation, the software automatically backs power down based on CDD power. Therefore, only the CDD mode was evaluated in this report. 4. 802.11n and 802.11ac have same modulation type and same power value, so we only show 802.11ac test data in report. 11 of 495 Report No.: 2412RSU039-U4 2.2. Test System Connection Diagram The device was tested per the guidance ANSI C63.10: 2013 was used to reference the appropriate EUT setup for radiated emissions testing and AC line conducted testing. Connection Diagram Cable Type A Power Cable B LAN Cable Product 1 Notebook Cable Description Non-Shielded Non-Shielded Manufacturer ThinkPad Length 1.5m > 10m Model No. E14 Gen 5 2.3. Test Software The test utility software used during testing was "QSPR" and the version was "5.0-00202". Final power setting please refer to operational description. 12 of 495 Report No.: 2412RSU039-U4 2.4. Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: FCC Part 15.407 KDB 789033 D02v02r01 KDB 662911 D01v02r01 ANSI C63.10-2013 2.5. Test Environment Condition Ambient Temperature Relative Humidity 15 ~ 35°C 20 ~ 75%RH 13 of 495 Report No.: 2412RSU039-U4 3. Antenna Requirements Excerpt from §15.203 of the FCC Rules/Regulations: "An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section." The antenna of the device is permanently attached. There are no provisions for connection to an external antenna. Conclusion: The unit complies with the requirement of §15.203. 14 of 495 Report No.: 2412RSU039-U4 4. Measuring Instrument Instrument Manufacturer Signal Analyzer Keysight Temperature Chamber BAOYT Thermohygrometer testo USB Power Sensor Keysight EMI Test Receiver R&S Two-Line V-Network R&S Four-Line V-Network R&S Thermohygrometer testo Shielding Room MIX-BEP Anechoic Chamber RIKEN Signal Analyzer Keysight Horn Antenna R&S Thermohygrometer testo Preamplifier MRT Signal Analyzer Keysight Horn Antenna Schwarzbeck Thermohygrometer testo Anechoic Chamber RIKEN Signal Analyzer Keysight Horn Antenna R&S Thermohygrometer testo Anechoic Chamber RIKEN TRILOG Broad Band Antenna Schwarzbeck Preamplifier EMCI Horn Antenna EMCI EMI Test Receiver R&S Horn Antenna Schwarzbeck Preamplifier EMCI EXA Signal Analyzer Keysight Thermohygrometer testo Anechoic Chamber TDK TRILOG Broad Band Antenna Schwarzbeck Active Loop Antenna Schwarzbeck EMI Test Receiver R&S Anechoic Chamber TDK Model No. Asset No. Cali. Interval Cali. Due Date Test Site N9010B MRTSUE07028 1 year 2025-10-13 SIP-TR1 BYG-408CS MRTSUE06847 1 year 2025-02-03 SIP-TR1 608-H1 MRTSUE11022 1 year 2024-10-28 SIP-TR1 U2021XA MRTSUE06596 1 year 2025-07-23 SIP-TR1 ESR3 MRTSUE06612 1 year 2025-05-08 SIP-SR2 ENV216 MRTSUE06003 1 year 2025-05-08 SIP-SR2 ENV432 MRTSUE06614 1 year 2025-10-13 SIP-SR2 608-H1 MRTSUE06621 1 year 2024-11-03 SIP-SR2 SIP-SR2 MRTSUE06949 5 years 2029-10-13 SIP-SR2 SIP-AC1 MRTSUE06554 1 year 2024-12-21 SIP-AC1 N9010B MRTSUE06559 1 year 2025-05-08 SIP-AC1 HF907 MRTSUE06610 1 year 2025-06-12 SIP-AC1 608-H1 MRTSUE06616 1 year 2025-10-16 SIP-AC1 AMP-AC1 MRTSUE11265 1 year 2024-11-03 SIP-AC1 N9010B MRTSUE07028 1 year 2025-10-13 SIP-AC2 BBHA 9120D MRTSUE06648 1 year 2024-10-21 SIP-AC2 608-H1 MRTSUE06622 1 year 2024-11-03 SIP-AC2 SIP-AC2 MRTSUE06781 1 year 2024-12-21 SIP-AC2 N9010B MRTSUE07028 1 year 2025-10-13 SIP-AC3 HF907 MRTSUE06611 1 year 2025-07-07 SIP-AC3 608-H1 MRTSUE06619 1 year 2024-10-28 SIP-AC3 SIP-AC3 MRTSUE06782 1 year 2024-12-21 SIP-AC3 VULB 9163 MRTSUE07097 1 year 2025-04-24 WJ-AC2 EMC118A45SE MRTSUE07102 1 year 2025-04-11 WJ-AC2 DRH18-E MRTSUE07105 1 year 2025-05-12 WJ-AC2 ESR3 MRTSUE07111 1 year 2025-04-18 WJ-AC2 BBHA 9170 MRTSUE06597 1 year 2024-11-04 WJ-AC2 EMC184045SE MRTSUE06640 1 year 2025-01-11 WJ-AC2 N9010B MRTSUE07147 1 year 2025-04-28 WJ-AC2 608-H1 MRTSUE11315 1 year 2025-06-24 WJ-AC2 WJ-AC2 MRTSUE07117 1 year 2025-05-14 WJ-AC2 VULB 9163 MRTSUE07099 1 year 2025-04-24 WJ-AC1 FMZB 1519-60 D MRTSUE07076 1 year 2024-12-04 WJ-AC1 ESR3 MRTSUE07110 1 year 2025-04-24 WJ-AC1 WJ-AC1 MRTSUE07115 1 year 2025-05-17 WJ-AC1 15 of 495 Thermohygrometer testo 608-H1 Software Version e3 230711 Controller_MF 7802BS 1.02 CONTROLLER CO3000 v 1.03.02 Agilent Power Analyzer/Agilent Power Panel V R03.09.00 Report No.: 2412RSU039-U4 MRTSUE11333 1 year 2025-06-24 WJ-AC1 Function EMI Test Software RE Antenna & Turntable RE Antenna & Turntable Power 16 of 495 Report No.: 2412RSU039-U4 5. Decision Rules and Measurement Uncertainty 5.1. Decision Rules The Decision Rule is based on Simple Acceptance in accordance with ISO Guide 98-4: 2012 Clause 8.2. (Measurement uncertainty is not taken into account when stating conformity with a specified requirement.) 5.2. Measurement Uncertainty Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement The maximum measurement uncertainty is evaluated as: 9kHz~150kHz: 3.58dB 150kHz~30MHz: 3.20dB Radiated Emission Measurement The maximum measurement uncertainty is evaluated as: Coaxial: 9kHz~30MHz: 2.61dB Coplanar: 9kHz~30MHz: 2.62dB Horizontal: 30MHz~200MHz: 3.79dB 200MHz~1GHz: 3.91dB 1GHz~40GHz: 4.99dB Vertical: 30MHz~200MHz: 4.06dB 200MHz~1GHz: 5.21dB 1GHz~40GHz: 4.90dB Spurious Emissions, Conducted Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.2dB Output Power Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 1.4dB Power Spectrum Density Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.2dB Occupied Bandwidth Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.7% 17 of 495 Report No.: 2412RSU039-U4 6. Test Result 6.1. Summary FCC Section(s) 15.407(a) Test Description 26dB & 99% Bandwidth Test Condition Verdict Pass 15.407(e) 6dB Bandwidth Pass 15.407(a)(1)(ii), (2), (3)(i) Maximum Conducted Output Power Pass 15.407(h)(1) 15.407(g) Transmit Power Control Frequency Stability Conducted Pass Pass 15.407(a)(1)(ii), (2), (3)(i), (13) Peak Power Spectral Density Pass 15.407(h)(2) Dynamic Frequency Selection (DFS) Pass Remark 3 15.407(b)(1), (2), (3), (4)(i) Undesirable Emissions Pass 15.205, 15.209 15.407(b)(8), (9), (10) General Field Strength Limits (Restricted Bands and Radiated Emission Limits) Radiated Pass 15.207 AC Conducted Emissions 150kHz - 30MHz Line Conducted Pass Remark: 1. The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 2. For radiated emission test, every axis (X, Y, Z) was also verified. The test results shown in the following sections represent the worst-case emissions. 3. DFS report refers to 2412RSU039-U5. 4. All test data in this report refer to the test data from FCC ID: 2AI9TOAW-AP152X. 18 of 495 Report No.: 2412RSU039-U4 6.2. 26dB & 99% Bandwidth Measurement 6.2.1. Test Limit N/A 6.2.2. Test Procedure KDB 789033 D02v02r01- Section II)C)1) (26dB Bandwidth) KDB 789033 D02v02r01- Section II)D) (99% Bandwidth) 6.2.3. Test Setting 26dB Bandwidth 1. The analyzers' automatic bandwidth measurement capability was used to perform the 26dB bandwidth 2. RBW = approximately 1% of the emission bandwidth. 3. VBW > RBW 4. Detector = Peak. 5. Trace mode = max hold. 6. Measure the maximum width of the emission that is 26 dB down from the maximum of the emission. Compare this with the RBW setting of the analyzer. Readjust RBW and repeat measurement as needed until the RBW/EBW ratio is approximately 1%. 99% Bandwidth 1. Set center frequency to the nominal EUT channel center frequency. 2. RBW = 1% to 5% of the OBW 3. VBW 3 RBW 4. Span = 1.5 times to 5 times the OBW 5. Detector = peak 6. Trace mode = max hold 7. Allow the trace to stabilize 8. Use the 99% power bandwidth function of the instrument. 6.2.4. Test Setup 19 of 495 6.2.5. Test Result Refer to Appendix A.2. Report No.: 2412RSU039-U4 20 of 495 Report No.: 2412RSU039-U4 6.3. 6dB Bandwidth Measurement 6.3.1. Test Limit The minimum 6dBbandwidth shall be at least 500 kHz. 6.3.2. Test Procedure KDB 789033 D02v02r01- Section II)C)2) 6.3.3. Test Setting 1. Set center frequency to the nominal EUT channel center frequency. 2. RBW = 100 kHz. 3. VBW 3 × RBW. 4. Detector = Peak. 5. Trace mode = max hold. 6. Sweep = auto couple. 7. Allow the trace to stabilize. 8. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 6.3.4. Test Setup 6.3.5. Test Result Refer to Appendix A.3. 21 of 495 Report No.: 2412RSU039-U4 6.4. Output Power Measurement 6.4.1. Test Limit For the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W (30dBm). If transmitting antennas of directional gain greater than 6dBi are used, the maximum conducted output power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 6.4.2. Test Procedure KDB 789033D02v02r01- Section II)E)3)b) Method PM-G 6.4.3. Test Setting Average Power Measurement Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. 6.4.4. Test Setup 6.4.5. Test Result Refer to Appendix A.4. 22 of 495 Report No.: 2412RSU039-U4 6.5. Transmit Power Control Measurement 6.5.1. Test Limit The U-NII device is required to have the capability to operate at least 6 dB below the mean EIRP value of 30 dBm. 6.5.2. Test Procedure KDB 789033 D02v02r01- Section II)E)3)b) Method PM-G 6.5.3. Test Setting Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. The trace was averaged over 100 traces to obtain the final measured average power. 6.5.4. Test Setup 6.5.5. Test Result Device supports TPC mechanism, details refer to the operational description. 23 of 495 Report No.: 2412RSU039-U4 6.6. Power Spectral Density Measurement 6.6.1. Test Limit For the band 5.15-5.25 GHz, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. For the band 5.725-5.85 GHz, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6dBi are used, the peak power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 6.6.2. Test Procedure KDB 789033 D02v02r01-Section II)F) 6.6.3. Test Setting 1. Analyzer was set to the center frequency of the UNII channel under investigation 2. Span was set to encompass the entire 26dB EBW of the signal. 3. RBW = 1MHz (510kHz, if measurement bandwidth of Maximum PSD is specified in 500 kHz) 4. VBW = 3 × RBW 5. Number of sweep points 2 × (span / RBW) 6. Detector = power averaging (Average) 7. Sweep time = auto 8. Trigger = free run 9. Trace average at least 100 traces in power averaging (rms) mode; however, the number of traces to be averaged shall be increased above 100 as needed to ensure that the average accurately represents the true average over the on and off periods of the transmitter. 10. Use the peak search function on the instrument to find the peak of the spectrum and record its value. 11. Add 10*log(1/x), where x is the duty cycle, to the measured power in order to compute the average power during the actual transmission times (because the measurement represents an average over both the on and off times of the transmission). For example, add 10*log(1/0.25) = 6 dB if the duty cycle is 25 percent. 24 of 495 6.6.4. Test Setup 6.6.5. Test Result Refer to Appendix A.5. Report No.: 2412RSU039-U4 25 of 495 Report No.: 2412RSU039-U4 6.7. Frequency Stability Measurement 6.7.1. Test Limit Manufactures of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user's manual. 6.7.2. Test Procedure Frequency Stability Under Temperature Variations: The equipment under test was connected to an external AC or DC power supply and input rated voltage. RF output was connected to a frequency counter or spectrum analyzer via feed through attenuators. The EUT was placed inside the temperature chamber. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and measure EUT 20°C operating frequency as reference frequency. Turn EUT off and set the chamber temperature to highest. After the temperature stabilized for approximately 30 minutes recorded the frequency. Repeat step measure with 10°C decreased per stage until the lowest temperature reached. Frequency Stability Under Voltage Variations: Set chamber temperature to 20°C. Use a variable AC power supply / DC power source to power the EUT and set the voltage to rated voltage. Set the spectrum analyzer RBW low enough to obtain the desired frequency resolution and recorded the frequency. Reduce the input voltage to specify extreme voltage variation (±15%) and endpoint, recordthe maximum frequency change. 6.7.3. Test Setup 26 of 495 6.7.4. Test Result Refer to Appendix A.6. Report No.: 2412RSU039-U4 27 of 495 Report No.: 2412RSU039-U4 6.8. Radiated Spurious Emission Measurement 6.8.1. Test Limit All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table per Section 15.209. Frequency [MHz] 0.009 - 0.490 0.490 - 1.705 1.705 - 30 30 - 88 88 - 216 216 - 960 Above 960 FCC Part 15 Subpart C Paragraph 15.209 Field Strength [uV/m] 2400/F (kHz) 24000/F (kHz) 30 100 150 200 500 Measured Distance [Meters] 300 30 30 3 3 3 3 6.8.2. Test Procedure KDB 789033 D02v02r01- Section II)G) 6.8.3. Test Setting Table 1 - RBW as a function of frequency Frequency RBW 9 ~ 150 kHz 200 ~ 300 Hz 0.15 ~ 30 MHz 9 ~ 10 kHz 30 ~ 1000 MHz 100 ~ 120 kHz > 1000MHz 1MHz 28 of 495 Report No.: 2412RSU039-U4 Quasi-Peak Measurements below 1GHz 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. Span was set greater than 1MHz 3. RBW = as specified in Table 1 4. Detector = CISPR quasi-peak 5. Sweep time = auto couple 6. Trace was allowed to stabilize Peak Measurements above 1GHz 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3MHz 4. Detector = Peak 5. Sweep time = Auto couple 6. Trace mode = Max hold 7. Trace was allowed to stabilize Average Measurements above 1GHz (Method VB) 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW; if the EUT is configured to transmit with duty cycle 98%, set VBW = 10Hz If the EUT duty cycle is < 98%, set VBW 1/T. T is the minimum transmission duration. 4. As an alternative, the instrument may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some instruments require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to "Voltage" regardless of the display mode 5. Detector = Peak 6. Sweep time = Auto 7. Trace mode = Max hold 8. Trace was allowed to stabilize 29 of 495 6.8.4. Test Setup Below 30MHz Test Setup: Report No.: 2412RSU039-U4 Below 1GHz Test Setup: 30 of 495 Above 1GHz Test Setup: Report No.: 2412RSU039-U4 6.8.5. Test Result Refer to Appendix A.7. 31 of 495 Report No.: 2412RSU039-U4 6.9. Radiated Restricted Band Edge Measurement 6.9.1. Test Limit For 15.205 requirement: Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a) of FCC part 15, must also comply with the radiated emission limits specified in Section 15.209(a). Frequency (MHz) 0.090 - 0.110 1 0.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 Frequency (MHz) 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 - 156.52525 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 - 335.4 -- Frequency (MHz) 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2690 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 -- Frequency (GHz) 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5 (2) -- 32 of 495 Report No.: 2412RSU039-U4 For 15.407(b) requirement: For transmitters operating in the 5.15-5.25 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.25-5.35 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.47-5.725 GHz band: All emissions outside of the 5.47-5.725 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.725-5.85 GHz band: All emissions shall be limited to a level of -27 dBm/MHz at 75 MHz or more above or below the band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25 MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or below the band edge, and from 5 MHz above or below the band edge increasing linearly to a level of 27 dBm/MHz at the band edge. Refer to KDB 789033 D02v02r01 G)2)c), as specified in §15.407(b), emissions above 1000 MHz that are outside of the restricted bands are subject to a maximum emission limit of -27 dBm/MHz (or -17 dBm/MHz as specified in § 15.407(b)(4)). However, an out-of-band emission that complies with both the peak and average limits of §15.209 is not required to satisfy the -27 dBm/MHz or -17 dBm/MHz maximum emission limit. All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47CFR must not exceed the limits shown in Table per Section 15.209. Frequency [MHz] FCC Part 15 Subpart C Paragraph 15.209 Field Strength [uV/m] Measured Distance [Meters] 0.009 - 0.490 2400/F (kHz) 300 0.490 - 1.705 24000/F (kHz) 30 1.705 - 30 30 30 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 33 of 495 Report No.: 2412RSU039-U4 6.9.2. Test Procedure KDB 789033 D02v02r01- Section II)G) 6.9.3. Test Setting Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW; If the EUT is configured to transmit with duty cycle 98%, set VBW = 10 Hz. If the EUT duty cycle is < 98%, set VBW 1/T. T is the minimum transmission duration. 4. As an alternative, the instrument may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some instruments require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to "Voltage" regardless of the display mode 5. Detector = Peak 6. Sweep time = auto 7. Trace mode = max hold 8. Allow max hold to run for at least 50 times (1/duty cycle) traces 34 of 495 6.9.4. Test Setup Report No.: 2412RSU039-U4 6.9.5. Test Result Refer to Appendix A.8. 35 of 495 Report No.: 2412RSU039-U4 6.10. AC Conducted Emissions Measurement 6.10.1. Test Limit Frequency (MHz) FCC Part 15.207 Limits QP (dBuV) AV (dBuV) 0.15 - 0.50 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 6.10.2. Test Setup 6.10.3. Test Result Refer to Appendix A.9. 36 of 495 Report No.: 2412RSU039-U4 Appendix A Test Result A.1 Duty Cycle Test Result Test Site Test Date SIP-TR1 2024-09-11 Test Engineer Ryan Wang Test Mode 802.11a 802.11ac-VHT20 802.11ac-VHT40 802.11ac-VHT80 802.11ac-VHT160 802.11ax-HE20 802.11ax-HE40 Duty Cycle 98.84% 97.29% 96.49% 97.29% 96.89% 96.92% 97.03% Test Mode 802.11ax-HE80 802.11ax-HE160 802.11be-EHT20 802.11be-EHT40 802.11be-EHT80 802.11be-EHT160 -- Duty Cycle 97.57% 96.53% 97.18% 97.84% 97.04% 97.82% -- Duty Cycle (T = Transmission Duration) 802.11a (T = 1.968ms) 802.11ac-VHT20 (T = 5.416ms) 802.11ac-VHT40 (T = 5.394ms) 802.11ac-VHT80 (T = 5.416ms) 37 of 495 Report No.: 2412RSU039-U4 Duty Cycle (T = Transmission Duration) 802.11ac-VHT160 (T = 5.416ms) 802.11ax-HE20 (T = 5.439ms) 802.11ax-HE40 (T = 5.416ms) 802.11ax-HE80 (T = 5.432ms) 802.11ax-HE160 (T = 5.432ms) 802.11be-EHT20 (T = 5.447ms) 38 of 495 Report No.: 2412RSU039-U4 Duty Cycle (T = Transmission Duration) 802.11be-EHT40 (T = 5.447ms) 802.11be-EHT80 (T = 5.439ms) 802.11be-EHT160 (T = 5.439ms) 39 of 495 Report No.: 2412RSU039-U4 A.2 26dB Bandwidth Test Result Test Site Test Date SIP-TR1 Test Engineer 2024-09-12 ~ 2024-09-22 Ryan Wang Test Mode 11a 11a 11a 11a 11a 11a 11a 11a 11a 11a 11a 11a 11a 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 11ac-VHT20 Data Rate/ MCS 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps 6Mbps MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 Channel No. 36 44 48 52 60 64 100 116 140 144 149 157 165 36 44 48 52 60 64 100 116 140 144 149 157 165 Frequency (MHz) 5180 5220 5240 5260 5300 5320 5500 5580 5700 5720 5745 5785 5825 5180 5220 5240 5260 5300 5320 5500 5580 5700 5720 5745 5785 5825 26dB Bandwidth 99% Bandwidth (MHz) (MHz) 22.51 22.59 22.62 22.39 22.42 22.43 22.29 22.39 22.22 22.38 22.62 22.64 22.42 16.933 16.933 16.887 16.876 16.933 16.829 16.856 16.796 16.814 16.823 16.849 16.774 16.947 23.00 22.87 22.63 23.26 23.34 22.99 23.26 23.02 23.24 22.81 23.19 23.12 22.59 17.937 17.899 17.943 17.938 17.970 17.954 17.961 17.946 17.968 17.904 17.913 17.956 17.936 40 of 495 Report No.: 2412RSU039-U4 Test Mode 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT40 11ac-VHT80 11ac-VHT80 11ac-VHT80 11ac-VHT80 11ac-VHT80 11ac-VHT80 11ac-VHT160 11ac-VHT160 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 11ax-HE20 Data Rate/ MCS MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 Channel No. 38 46 54 62 102 110 134 142 151 159 42 58 106 122 138 155 50 114 36 44 48 52 60 64 100 116 140 144 149 157 165 Frequency (MHz) 5190 5230 5270 5310 5510 5550 5670 5710 5755 5795 5210 5290 5530 5610 5690 5775 5250 5570 5180 5220 5240 5260 5300 5320 5500 5580 5700 5720 5745 5785 5825 26dB Bandwidth 99% Bandwidth (MHz) (MHz) 44.55 43.68 45.66 44.85 45.57 43.75 44.09 44.54 43.35 44.30 36.495 36.461 36.655 36.632 36.490 36.490 36.513 36.527 36.492 36.503 91.52 92.43 91.95 92.00 93.32 90.02 76.463 76.189 76.179 76.201 76.236 76.173 170.3 173.4 155.73 155.57 22.03 22.41 22.73 22.68 21.91 21.97 23.24 23.03 22.15 23.11 23.20 22.58 22.79 19.047 19.069 19.088 19.128 19.068 19.052 19.032 19.049 19.068 19.126 19.052 19.076 19.051 41 of 495 Report No.: 2412RSU039-U4 Test Mode 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE40 11ax-HE80 11ax-HE80 11ax-HE80 11ax-HE80 11ax-HE80 11ax-HE80 11ax-HE160 11ax-HE160 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 11be-EHT20 Data Rate/ MCS MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 Channel No. 38 46 54 62 102 110 134 142 151 159 42 58 106 122 138 155 50 114 36 44 48 52 60 64 100 116 140 144 149 157 165 Frequency (MHz) 5190 5230 5270 5310 5510 5550 5670 5710 5755 5795 5210 5290 5530 5610 5690 5775 5250 5570 5180 5220 5240 5260 5300 5320 5500 5580 5700 5720 5745 5785 5825 26dB Bandwidth 99% Bandwidth (MHz) (MHz) 43.93 42.94 42.49 43.36 43.71 44.07 43.82 43.34 44.18 43.92 37.978 37.970 38.015 37.978 38.037 37.960 37.984 38.072 38.025 37.996 89.66 86.26 88.36 89.37 88.71 88.72 77.690 77.786 77.661 77.662 77.700 77.623 172.2 172.0 156.97 157.01 23.80 23.73 22.76 23.47 23.59 23.35 23.51 22.68 23.26 23.69 23.14 23.61 24.08 19.074 19.042 19.056 19.065 19.146 19.041 19.054 19.081 19.054 19.063 19.097 19.084 19.092 42 of 495 Report No.: 2412RSU039-U4 Test Mode 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT40 11be-EHT80 11be-EHT80 11be-EHT80 11be-EHT80 11be-EHT80 11be-EHT80 11be-EHT160 11be-EHT160 Data Rate/ MCS MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 MCS0 Channel No. 38 46 54 62 102 110 134 142 151 159 42 58 106 122 138 155 50 114 Frequency (MHz) 5190 5230 5270 5310 5510 5550 5670 5710 5755 5795 5210 5290 5530 5610 5690 5775 5250 5570 26dB Bandwidth 99% Bandwidth (MHz) (MHz) 43.02 44.39 43.30 43.40 43.46 44.08 42.34 43.91 42.51 43.58 37.973 37.988 38.031 38.025 37.953 37.988 38.051 38.004 37.965 38.024 88.61 87.71 88.47 91.88 90.37 89.27 77.694 77.709 77.678 77.612 77.583 77.737 171.6 170.8 157.05 156.91 Test Mode Data Rate/ MCS Channel No. Frequency (MHz) FH (MHz) 802.11a 6Mbps 48 5240 5248.44 802.11ac-VHT20 MCS0 48 5240 5248.97 802.11ac-VHT40 MCS0 46 5230 5248.23 802.11ac-VHT80 MCS0 42 5210 5248.23 802.11ax-HE20 MCS0 48 5240 5249.54 802.11ax-HE40 MCS0 46 5230 5248.99 802.11ax-HE80 MCS0 42 5210 5248.85 802.11be-EHT20 MCS0 48 5240 5249.53 802.11be-EHT40 MCS0 46 5230 5248.99 802.11be-EHT80 MCS0 42 5210 5248.85 Note: FH = Centre frequency + 99% OBW / 2. For example, 802.11a 5240MHz, FH = 5240 MHz + 16.887 MHz / 2 = 5248.44 MHz. Limit (MHz) < 5250 < 5250 < 5250 < 5250 < 5250 < 5250 < 5250 < 5250 < 5250 < 5250 43 of 495 Report No.: 2412RSU039-U4 802.11a 26dB Bandwidth & 99% Bandwidth Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) 44 of 495 Channel 100 (5500MHz) Report No.: 2412RSU039-U4 Channel 116 (5580MHz) 45 of 495 Report No.: 2412RSU039-U4 802.11a 26dB Bandwidth & 99% Bandwidth Channel 140 (5700MHz) Channel 144(5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 46 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT20 26dB Bandwidth & 99% Bandwidth Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) 47 of 495 Channel 100 (5500MHz) Report No.: 2412RSU039-U4 Channel 116 (5580MHz) 48 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT20 26dB Bandwidth & 99% Bandwidth Channel 140 (5700MHz) Channel 144(5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 49 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT40 26dB Bandwidth & 99% Bandwidth Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 54 (5270MHz) Channel 62 (5310MHz) Channel 102 (5510MHz) Channel 110 (5550MHz) 50 of 495 Channel 134 (5670MHz) Report No.: 2412RSU039-U4 Channel 142(5710MHz) 51 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT40 26dB Bandwidth & 99% Bandwidth Channel 151 (5755MHz) Channel 159 (5795MHz) 52 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT80 26dB Bandwidth & 99% Bandwidth Channel 42 (5210MHz) Channel 58 (5290MHz) Channel 106 (5530MHz) Channel 122 (5610MHz) Channel 138 (5690MHz) Channel 155 (5775MHz) 53 of 495 Report No.: 2412RSU039-U4 802.11ac-VHT160 26dB Bandwidth & 99% Bandwidth Channel 50 (5250MHz) Channel 114 (5570MHz) 54 of 495 Report No.: 2412RSU039-U4 802.11ax-HE20 26dB Bandwidth & 99% Bandwidth Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) 55 of 495 Channel 100 (5500MHz) Report No.: 2412RSU039-U4 Channel 116 (5580MHz) 56 of 495 Report No.: 2412RSU039-U4 802.11ax-HE20 26dB Bandwidth & 99% Bandwidth Channel 140 (5700MHz) Channel 144(5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) 57 of 495
Related FCC IDs:
- 2ALJ3AP52X - HAN Networks Co., Ltd. HAN Access Point [AP52X] Microsoft Word 适用于 Microsoft 365