Antenna information

Dongguan Lingdu Electronic Technology Co.,Ltd V620 2BEAP-V620 2BEAPV620 v620

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 13 Pages, 1,021.45KB

Document DEVICE REPORTGetApplicationAttachment.html?id=7633388 
Document number:
Sample acceptance letter

Specification For Approval

Customer name: customer:

Dongguan lingdu electronic technology co., ltd

Name of supplier: Customer:
Customer Item:

Shenzhen Guangyuanfa Electronics Co., Ltd.
V630-WIFI-V1.0 GYF Supplier Item: 2024-07-12

Product description:

WIFI antenna (V630) coaxial line length: 2nd generation terminal L=65mm, line diameter: 0.81mm, silk
Seal: V630-WIFI-V1.0 GYF 2024-07-12

Matching model:

V630

Supplier acknowledges (seals):

Customer acknowledges (seals):

Production: Guo Shaosen

Structure: Ma Shuaixi

Audit: Zhou Xuefeng Date: July 12, 2024

Address: 10th Floor, D2 Building, Songhu Zhigu Innovation Center, Liaobu Town, Dongguan, Dongguan Guangyuanfa Electronics Co., Ltd.

Tel: 0755-26702159



Fax: 0755-26702585

Website: http://www.gyfgpsbd.com/



1. specifications
1.1 Electrical specification 1.2 Antenna frequency range
2. Matching circuit diagram
3. structural style
3.1 Antenna composition
4. testing equipment
5. VSWR test connection
5.1 test connection
6. test
6.1 Test site 6.2 Tested instrument 6.3 Test data
7. Drawing specification
7.1 blueprint 7.2 Sample size detection 7.3 Bill Of Material
8. reliability testing
8.1 Reliability test report 8.2 Product storage instructions
9. Working temperature
10. Antenna picture

catal ogue

2 / 13



V630 antenna

1. specificati ons
1.1 Electrical specificat ion

This report mainly provides the test status of various electrical and structural performance parameters of the V630 antenna.

specifications and models
WIFI antenna

Guang yuan fa Liao Hao
V630-WIFI-V1.0 GYF 2024-07-12

1.2 Antenna frequency range
The following table is the electrical performance index of Guangyuanfa design and mass production antenna.

v630

WIFI
2. Matching circuit diagram
3 / 13

 3. structural
style
3.1 Antenna composition The antenna is mainly composed of flexible printed circuit board and coaxial line.
4. testing equipment
5 . VSWR test connection
5.1 Test connection: VSWR test device is connected in sequence as: R&SZVL network analyzer  test line  test fixture.
6. test
6.1 Test site: Guangyuan microwave darkroom. The test frequency range is 400 MHz-6 GHz, the dead zone range is 50cm Ruta, and the reflectivity is less than -50 dB.
6.2 Tested instruments: Agilent5071B, CMW500, Agilent8960 E5515C, standard horn antenna, 24-probe OTA microwave darkroom test system, printer, etc.
4 / 13

6.3 Test data:



5 / 13


6 / 13


7. Drawing specification
7.1 blueprint
7 / 13



7.2 Sample size detection

Project name
Item order
one 2 three four five six seven eight nine 10 11 twelve 13 14 15 16 17 18 19 twenty 21 22 23

V63 0
specific ations
one 21.88 21.86 30.75 30.74 65.00 65..46 0.81 0.80

Finished item
number
2 21.85 30.77 65.56 0.81

V630-WIFI-V1.0 GYF 2024-07-12

Measure d data three 21.87
30.75
65.62
0.79

four 21.87 30.76 65.57 0.82

date
five 13.88 30.77 65.61 0.78

2024.07.04
decide remark s
OK OK OK OK

8 / 13



7.3 Bill Of Material
Project name
Bill Of Material
one
three
four five six seven eight nine 10 11 twelve 13 14 15 16 17 18 19 twenty

V630
category
Fpc antenna coaxial-
line

Bill Of Material

Finished item
number texture of
wood
One and a half.
copper

V630-WIFI-V1.0

date

GYF 2024-07-12

speci ficati ons 30.75*21.88mm
0.81 black 65mm secondgeneration terminal

2024.07.04 dosage one one

9 / 13



8. reliability testing
8.1 Reliability test report
Project name V630
Test quantity 15pcs

Finished item
number
start time

V630-WIFI-V1.0 GYF 2024-07-12
June 11th, 09:15

test item
Salt spray corrosi on test
Low tempe rature test

testing nominati
ve
(1) Test temperature: salt water test 35 2; Pressure barrel 47 1 2 Test conditions/methods: salt water concentration is above 5%, solution PH is 6.5~7.2, air pressure is 1.0 ~ 1.2 kg/cm ,
and test time is set according to product requirements. 3 Test finished: after 2 hours, observe the
product surface. Surface oxidation discoloration, coating shedding phenomenon (1) Temperature:-30 (-25-pilot stage) 2 Test time: 20 hours/packing condition: no packing. 3 The product to be tested is placed in a high and low temperature test box without turning on the machine, and the temperature in the box is adjusted to be 25 and the
humidity to be 65% for 1 hour, and then the temperature is reduced to -30 and the
humidity within 1 hour. Closing, keeping the temperature for 20 hours, raising the temperature for 1 hour, then cooling to normal temperature, and performing performance test after 2 hours. Appearance and structure: the appearance and surface of the antenna shall be free from defects, and the antenna shall be free from deformation, warping and damage, and its performance shall be normal, and the standing wave ratio shall not exceed the product standard. 10%

Test qua ntity 5pcs
5pcs

date finish time
test result
OK
OK

2024.07.04 June 13th at
11:25. rem arks
Test time 48H
Test time is 20H.

10 / 13



(1) Temperature:+70 (+65-pilot

stage) and humidity 85% (80%-pilot

stage) 2 Test time: 20 hours/packing condition:

no packing.

High tempe

3 The product to be tested is placed in the high and low temperature test box without

5pcs

OK

rature test

turning on the machine, and the temperature in the box is adjusted to be 25 and the

humidity to be 65% for 1 hour, and then the

temperature is raised to +70 and humidity

within 1 hour.

After 85% heat preservation for 20 hours, the

temperature is cooled for 1 hour and then

cooled to normal temperature, and the

performance is tested after 2 hours.

Appearance and structure: the appearance and

surface of the antenna shall be free from

defects, and the antenna shall be free from

deformation, warping and damage, and its

performance shall be normal, and the

standing wave ratio shall not exceed the

product standard.

10%

11 / 13



8.2 Product storage instructions
1. The exposed part of the gold finger conductor needs surface plating (anti-rust) treatment, such as gold plating, OSP, tin plating, etc., and the storage environment needs to avoid corrosive gases. 2. The antenna temperature needs to be controlled at 21-38, and the humidity needs to be controlled at 50-70%. If the
temperature is too high, the 3M glue will melt, which will make the antenna sticky. 3. It is suggested that if the initial bonding temperature is lower than 10, it is not suitable for bonding, so the adhesive is too hard to be firmly bonded to the object. However, if it has been bonded, the adhesion at low temperature is also satisfactory. 3. Under the condition of 21 and 50% relative humidity, the shelf life of the original packaging is 24 months from the date of production.

9. Working temperature
components FPC body 3m glue (pasted to the machine)
10. Antenna picture

temperature -50~280 -30-80

12 / 13

Related FCC IDs:

Search Any Device: