FiberRunner Application Guide - Section 9
MSO
Compliance Cert
Panduit FADC4X4 :: Fitting, Adapter from 4" x 4" (100mm x 1 :: Gexpro
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 18 Pages, 1.93MB
Document DEVICE REPORT01f747e7ed192ac2a48224a85ad7e87d5e99c871 ?i=32839706-DAED-40BB-8F63-319B8ACEDD1APANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1. Adapters to Other Systems 1.1 FIBERRUNNER 2x2 Cable Routing System to Various 2x2 Systems The FIBERRUNNER 2x2 QUIKLOCKTM Coupler, when used with the FIBER-DUCTTM 2x2 Coupler allows the FIBERRUNNER 2x2 Cable Routing System to transition into various other fiber routing systems. The FIBERRUNNER 2x2 QUIKLOCK Coupler is supplied pre-assembled and mechanically attaches without the need to use any tools or tighten any bolts. The FIBERRUNNER 2x2 QUIKLOCK Coupler in conjunction with the FIBER-DUCT 2x2 Coupler is compatible with the following fiber routing systems: 1. ADC* 2x2 FiberGuide** System * ADC is a registered trademark of ADC Telecommunications, Inc. ** FiberGuide is a registered trademark of ADC Telecommunications, Inc. 2. Ditel*** 2x2 LIGHTRAX**** Fiber Raceway System *** Ditel is a trademark of Tyco Electronics Corporation. **** LIGHTRAX is a trademark of Tyco Electronics Corporation. 3. Newton***** 2x2 Fiber Cable Management System ***** Newton is a trademark of Newton Instrument Company, Inc. 4. Tyton****** 2x2 Lightguide******* Fiber Optic Protection System ****** Tyton is a registered trademark of HellermannTyton Corporation. ******* Lightguide is a trademark of HellermannTyton Corporation. © 2005 PANDUIT Corp. 9-2 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 The FIBERRUNNER 2x2 QUIKLOCKTM Coupler and the FIBER-DUCTTM 2x2 Coupler can be easily installed as follows: 1. Align the extended flanges of the FIBER-DUCT 2x2 Coupler with the profile of the other channel section. Please note that the left and right extended flanges should be aligned with the outside of the channel section while the lower extended flange is aligned with the inside of the channel section. Once aligned slide the coupler over the end of the other channel section until the coupler is completely seated against the channel profile. Other 2x2 Channel FIBER-DUCT 2x2 Coupler (FCF2X2**) 2. With the coupler held in place against the other channel section, mark all three (3) mounting hole locations of the coupler on to the channel section. Remove the coupler and with a 5/16" diameter drill bit create three (3) mounting holes in the other channel. Please note that before the drilling operation begins, that all cables, etc. are out of the path of the drilling bit. 5/16" Drill Bit 3. Reattach the coupler and realign all three (3) of the mounting holes. With the coupler held in place, install the FIBER-DUCT 2x2 Snap Rivets to secure the installation. To ensure a smooth interior surface, it is recommended that the female rivet be used on the outside surfaces of the coupler. Also note that each FIBERDUCT 2x2 Coupler will use three (3) snap rivets. The Plastic Wing Nut and Screw Kit and/or the Plastic Hex Nut and Screw Kit can be used in lieu of the FIBER-DUCT 2x2 Snap Rivets. FIBER-DUCT 2x2 Snap Rivets (NR2WH-L) © 2005 PANDUIT Corp. 9-3 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 4. With the FIBER-DUCTTM 2x2 Coupler secured to the competitive channel section, line up the extended ribs of the FIBERRUNNER 2x2 QUIKLOCKTM Coupler with the extended flange of the FIBER-DUCT 2x2 Coupler. Once aligned, push the FIBERRUNNER 2x2 QUIKLOCK Coupler and the FIBER-DUCT 2x2 Coupler together until the FIBER-DUCT 2x2 Coupler is seated against the inner rib of the FIBERRUNNER 2x2 QUIKLOCK Coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the FIBERRUNNER 2x2 QUIKLOCK Coupler have engaged the surface of the FIBER-DUCT 2x2 Coupler. FIBERRUNNER 2x2 QUIKLOCK Coupler (FBC2X2**) 5. With the FIBERRUNNER 2x2 QUIKLOCK Coupler in place, a section of FIBERRUNNER 2x2 Hinged or Hinged Slotted Channel and/or FIBERRUNNER 2x2 fitting can be installed to continue the fiber pathway. FIBERRUNNER 2x2 Hinged or Hinged Slotted Channel or Fitting (H2X2**6 shown) © 2005 PANDUIT Corp. 9-4 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 In the event that disassembly is required, connections made with the FIBERRUNNER 2x2 QUIKLOCKTM Coupler can be easily disconnected as follows: 1. Using the FIBERRUNNER 5/16" Nut Driver loosen both of the bolts on the outside of the coupler. Please note that any standard 5/16" nut driver will work as well. Also note that the bolts only need to be loosened enough to allow the metal barbs to disengage the surfaces of the FIBER-DUCTTM 2x2 Coupler and the FIBERRUNNER 2x2 Hinged or Hinged Slotted Channel. Once loosened the connection can be easily pulled apart. FIBERRUNNER 5/16" Nut Driver (FR516DR) 2. The bolts of the coupler can then be re-tightened. Please be aware not to over tighten the bolts. Once tightened, the FIBERRUNNER 2x2 QUIKLOCK Coupler is ready for use once again. Part numbers described in this section: FBC2X2** - FIBERRUNNER 2x2 QUIKLOCK Coupler Part numbers referenced in this section: FCF2X2** - FIBER-DUCT 2x2 Coupler NR2WH-L FIBER-DUCT 2x2 Snap Rivets F14PWN-L Plastic Wing Nut and Screw Kit F14PN-L Plastic Hex Nut and Screw Kit HS2X2**6 FIBERRUNNER 2x2 Hinged Channel H2X2**6 FIBERRUNNER 2x2 Hinged Slotted Channel FR516DR FIBERRUNNER 5/16" Nut Driver When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black © 2005 PANDUIT Corp. 9-5 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.2 FIBERRUNNER 4x4 Cable Routing System to ADC* 4x4 FiberGuide** System The FIBERRUNNER 4x4 Cable Routing System to ADC 4x4 FiberGuide Adapter when used with the FIBERRUNNER 4x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 4x4 Cable Routing System to transition into or out of the ADC 4x4 FiberGuide System. The adapter slides into the rib structure of the ADC 4x4 FiberGuide Channel and is secured with four (4) ¼-20x" Hex Head Cap Screws, four (4) .312"x.734" Type A Plain Washers and four (4) ¼-20 Hex Nuts (included). The FIBERRUNNER 4x4 Cable Routing System to ADC 4x4 FiberGuide Adapter can be easily installed as follows: 1. Insert one (1) of the ¼-20x" Hex Head Cap Screws into each of the mounting holes on the adapter. Be sure that all four (4) of the cap screws are pointing outward away from the adapter. With the cap screws in place, slide the adapter into the rib structure of the ADC 4x4 FiberGuide Channel until the adapter is completely seated against the channel section. Note that the rib structure of the ADC channel will hold the cap screws in place. FIBERRUNNER 4x4 Cable Routing System to ADC 4x4 FiberGuide Adapter ADC 4x4 FiberGuide Channel (FRADC4X4BL) ¼-20x" Hex Head Cap Screw (Typical: 4 Places) 2. Install one (1) of the .312"x.734" Type A Plain Washers and thread one (1) of the ¼-20 Hex Nuts on to each of the cap screws and hand tighten. Tighten all four (4) of the ¼-20 Hex Nuts using the FIBERRUNNER 7/16" Nut Driver to secure the adapter installation. Please note that any standard 7/16" nut driver will work as well. If the use of hand tools is not preferred a nonmagnetic FIBERRUNNER 7/16" Nut Driver Bit is also available. ¼-20 Hex Nut (Typical: 4 Places) .312"x.734" Type A Plain Washer (Typical: 4 Places) FIBERRUNNER 7/16" Nut Driver (FR716DR) 3. With the adapter secured to the ADC 4x4 FiberGuide Channel, align the extended ribs of the FIBERRUNNER 4x4 QUIKLOCK Coupler with the FIBERRUNNER 4x4 Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 4x4 QUIKLOCK Coupler (FRBC4X4**) © 2005 PANDUIT Corp. 9-6 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 4. With THE FIBERRUNNER 4x4 QUIKLOCKTM Coupler in place a section of FIBERRUNNER 4x4 Channel and/or any FIBERRUNNER 4x4 fitting can be installed to continue the fiber pathway. FiberRunner 4x4 Channel or Fitting (FR4X4**6 shown) Part numbers described in this section: FRADC4X4BL - FIBERRUNNER 4x4 Cable Routing System to ADC 4x4 FiberGuide Adapter Part numbers referenced in this section: FRBC4X4** - FIBERRUNNER 4x4 QUIKLOCK Coupler FR4X4**6 FIBERRUNNER 4x4 Channel FR716DR FIBERRUNNER 7/16" Nut Driver FR716BIT FIBERRUNNER 7/16" Nut Driver Bit When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * ADC is a registered trademark of ADC Telecommunications, Inc. ** FiberGuide is a registered trademark of ADC Telecommunications, Inc. © 2005 PANDUIT Corp. 9-7 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.3 FIBERRUNNER 6x4 Cable Routing System to ADC* 4x6 FiberGuide** System The FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter allows the FIBERRUNNER 6x4 Cable Routing System to transition into or out of the ADC 4x6 FiberGuide System. The adapter utilizes the same QUIKLOCKTM feature as the FIBERRUNNER 6x4 QUIKLOCK Coupler and is supplied pre-assembled and mechanically attaches without the need to use any tools or tighten any bolts. The FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter can be easily installed as follows: 1. Align the ADC 4x6 FiberGuide Channel with the extended ribs of the ADC side of the adapter. Once aligned, push the adapter and channel together until the channel is seated against the inner rib of the adapter. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the adapter have engaged the surface of the channel. FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter (FRADC6X4**) ADC 4x6 FiberGuide Channel 2. Next, align the FIBERRUNNER 6x4 Channel and/or fitting with the extended ribs of the FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and channel/fitting together until the channel/fitting is seated against the inner rib of the adapter. FIBERRUNNER 6x4 Channel (FR6X4**6) © 2005 PANDUIT Corp. 9-8 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 In the event that disassembly is required, connections made with the FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter can be easily disconnected as follows: 1. Using the FIBERRUNNER " Nut Driver loosen all of the bolts on the outside of the adapter. Please note that any standard " nut driver will work as well. If the use of hand tools is not preferred a nonmagnetic FIBERRUNNER " Nut Driver Bit is also available. Also note that the bolts only need to be loosened enough to allow the metal barbs to disengage the surface of the channel section and/or fitting. Once loosened the connection can be easily pulled apart. FIBERRUNNER " Nut Driver (FR38DR) 2. The bolts of the adapter can then be re-tightened. Please be aware not to over tighten the bolts. Once tightened, the FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter is ready for use once again. Part numbers described in this section: FRADC6X4** - FIBERRUNNER 6x4 Cable Routing System to ADC 4x6 FiberGuide Adapter Part numbers referenced in this section: FR6X4**6 FIBERRUNNER 6x4 Channel FR38DR - FIBERRUNNER " Nut Driver FR38BIT FIBERRUNNER " Nut Driver Bit When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * ADC is a registered trademark of ADC Telecommunications, Inc. ** FiberGuide is a registered trademark of ADC Telecommunications, Inc. © 2005 PANDUIT Corp. 9-9 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.4 FIBERRUNNER 6x4 Cable Routing System to Tyton* 8x4 Lightguide** Fiber Optic Protection System The FIBERRUNNER 6x4 Cable Routing System to Tyton 8x4 Lightguide Adapter when used with the FIBERRUNNER 6x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 6x4 Cable Routing System to transition into or out of the Tyton 8x4 Lightguide Fiber Optic Protection System. The adapter slides over the Tyton 8x4 Lightguide Channel and is secured with four (4) ¼-20x" Nylon Phillips Binder Head Screws and four (4) ¼-20 Nylon Deco Wing Nuts (included). The FIBERRUNNER 6x4 Cable Routing System to Tyton 8x4 Lightguide Adapter can be easily installed as follows: 1. Align the profile of the Tyton 8x4 Lightguide Channel with the inside of the adapter. Slide the adapter over the end of the channel until the adapter is completely seated against the channel profile. FIBERRUNNER 6x4 Cable Routing System to Tyton 8x4 Lightguide Adapter (FRTYT68) Tyton 8x4 Lightguide Channel 2. With the adapter held in place, mark all four (4) mounting hole locations of the adapter on to the channel section. Remove the adapter and with a 9/32" diameter drill bit create four (4) mounting holes in the channel. Please note that before the drilling operation begins, that all cables, etc. are out of the path of the drilling bit. 9/32" Drill Bit 3. Reattach the adapter and realign all four (4) of the mounting holes. With the adapter held in place, insert one (1) of the ¼-20x" Nylon Phillips Binder Head Screws through each of the mounting holes from the inside of the channel. Be sure that all four (4) of the cap screws are pointing outward away from the adapter. Thread one (1) of the ¼-20 Nylon Deco Wing Nuts on to each of the binder head screws and hand tighten. ¼-20x" Nylon Phillips Binder Head Screw (Typical: 4 Places) © 2005 PANDUIT Corp. 9-10 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 ¼-20 Nylon Deco Wing Nut (Typical: 4 Places) 4. With the adapter secure to the Tyton 8x4 Lightguide Channel, align the extended ribs of the FIBERRUNNER 6x4 QUIKLOCKTM Coupler with the FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 6x4 QUIKLOCK Coupler (FRBC6X4**) 5. With the FIBERRUNNER 6x4 QUIKLOCK Coupler in place, a section of FIBERRUNNER 6x4 Channel and/or any FIBERRUNNER 6x4 fitting can be installed to continue the fiber pathway. FiberRunner 6x4 Channel or Fitting (FR6X4**6 shown) Part numbers described in this section: FRTYT68 - FIBERRUNNER 6x4 Cable Routing System to Tyton 8x4 Lightguide Adapter Part numbers referenced in this section: FRBC6X4** - FIBERRUNNER 6x4 QUIKLOCK Coupler FR6X4**6 FIBERRUNNER 6x4 Channel When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * Tyton is a registered trademark of HellermannTyton Corporation. ** Lightguide is a trademark of HellermannTyton Corporation. © 2005 PANDUIT Corp. 9-11 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.5 FIBERRUNNER 6x4 Cable Routing System to Warren & Brown* 8x4 Lightpath** Duct System The FIBERRUNNER 6x4 Cable Routing System to Warren & Brown 8x4 Lightpath Adapter when used with the FIBERRUNNER 6x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 6x4 Cable Routing System to transition into or out of the Warren & Brown 8x4 Lightpath Duct System. The adapter slides over the Warren & Brown 8x4 Lightpath Channel and is secured with four (4) ¼-20x" Nylon Phillips Binder Head Screws and four (4) ¼-20 Nylon Deco Wing Nuts (included). The FIBERRUNNER 6x4 Cable Routing System to Warren & Brown 8x4 Lightpath Adapter can be easily installed as follows: 1. Align the profile of the Warren & Brown 8x4 Lightpath Channel with the inside of the adapter. Slide the adapter over the end of the channel until the adapter is completely seated against the channel profile. Warren & Brown 8x4 Lightpath Channel FIBERRUNNER 6x4 Cable Routing System to Warren & Brown 8x4 Lightpath Adapter (FRWBS68) 2. Align the four (4) factory installed slots on the Warren & Brown 8x4 Lightpath Channel with the four (4) mounting holes on the adapter. If the factory installed slots are not available, hold the adapter in place and mark all four (4) of the mounting hole locations of the adapter on to the channel section. Remove the adapter and with a 9/32" diameter drill bit create four (4) mounting holes in the channel. Please note that before the drilling operation begins, that all cables, etc. are out of the path of the drilling bit. 9/32" Drill Bit 3. Reattach the adapter and realign all four (4) of the mounting holes. With the adapter held in place, insert one (1) of the ¼-20x" Nylon Phillips Binder Head Screws through each of the mounting holes from the inside of the channel. Be sure that all four (4) of the cap screws are pointing outward away from the adapter. Thread one (1) of the ¼-20 Nylon Deco Wing Nuts on to each of the binder head screws and hand tighten. ¼-20x" Nylon Phillips Binder Head Screw (Typical: 4 Places) © 2005 PANDUIT Corp. 9-12 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 ¼-20 Nylon Deco Wing Nut (Typical: 4 Places) 4. With the adapter secure to the Warren & Brown 8x4 Lightpath Channel, align the extended ribs of the FIBERRUNNER 6x4 QUIKLOCKTM Coupler with FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 6x4 QUIKLOCK Coupler (FRBC6X4**) 5. With the FIBERRUNNER 6x4 QUIKLOCK Coupler in place a section of FIBERRUNNER 6x4 Channel and/or any FIBERRUNNER 6x4 fitting can be installed to continue the fiber pathway. FIBERRUNNER 6x4 Channel or Fitting (FR6X4**6 shown) Part numbers described in this section: FRWBS68 - FIBERRUNNER 6x4 Cable Routing System to Warren & Brown 8x4 Lightpath Adapter Part numbers referenced in this section: FRBC6X4** - FIBERRUNNER 6x4 QUIKLOCK Coupler FR6X4**6 FIBERRUNNER 6x4 Channel When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * Warren & Brown is a registered trademark of Warren & Brown Technologies Pty Ltd. ** Lightpath is a registered trademark of Warren & Brown Technologies Pty Ltd. © 2005 PANDUIT Corp. 9-13 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.6 FIBERRUNNER 12x4 Cable Routing System to Newton* 4x8 Fiber Cable Management System The FIBERRUNNER 12x4 Cable Routing System to Newton 4x8 Adapter when used with the FIBERRUNNER 12x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 12x4 Cable Routing System to transition into or out of the Newton 4x8 Fiber Cable Management System. The adapter slides over the Newton 4x8 Solid and/or Slotted Wall Channel and is secured with the five (5) ¼-20x" Nylon Phillips Binder Head Screws and five (5) ¼-20 Nylon Deco Wing Nuts (included). The FIBERRUNNER 12x4 Cable Routing System to Newton 4x8 Adapter can be easily installed as follows: 1. Align the profile of the Newton 4x8 Solid and/or Slotted Wall Channel with the inside of the adapter. Slide the adapter over the end of the channel until the adapter is completely seated against the channel profile. FIBERRUNNER 6x4 Cable Routing System to Newton 4x8 Adapter (FRNWT128) Newton 4x8 Solid and/or Slotted Wall Channel 2. With the adapter held in place, mark all five (5) mounting hole locations of the adapter on to the channel section. Remove the adapter and with a 9/32" diameter drill bit create five (5) mounting holes in the channel. Please note that before the drilling operation begins, that all cables, etc. are out of the path of the drilling bit. 9/32" Drill Bit 3. Reattach the adapter and realign all five (5) of the mounting holes. With the adapter held in place, insert one (1) of the ¼-20x" Nylon Phillips Binder Head Screws through each of the mounting holes from the inside of the channel. Be sure that all five (5) of the binder head screws are pointing outward away from the adapter. Thread one (1) of the ¼-20 Nylon Deco Wing Nuts on to each of the binder head screws and hand tighten. ¼-20x" Nylon Phillips Binder Head Screw (Typical: 5 Places) © 2005 PANDUIT Corp. 9-14 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 ¼-20 Nylon Deco Wing Nut (Typical: 5 Places) 4. With the adapter secure to the Newton 4x8 Solid and/or Slotted Wall Channel, align the extended ribs of the FIBERRUNNER 12x4 QUIKLOCKTM Coupler with the FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 12x4 QUIKLOCK Coupler (FRBC12X4**) 5. With the FIBERRUNNER 12x4 QUIKLOCK Coupler in place, a section of FIBERRUNNER 12x4 Channel and/or any FIBERRUNNER 12x4 Fitting can be installed to continue the fiber pathway. FiberRunner 12x4 Channel or Fitting (FR12X4**6 shown) Part numbers described in this section: FRNWT128 - FIBERRUNNER 12x4 Cable Routing System to Newton 4x8 Adapter Part numbers referenced in this section: FRBC12X4** - FIBERRUNNER 12x4 QUIKLOCK Coupler FR12X4**6 FIBERRUNNER 12x4 Channel When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * Newton is a trademark of Newton Instrument Company, Inc. © 2005 PANDUIT Corp. 9-15 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.7 FIBERRUNNER 12x4 Cable Routing System to ADC* 4x12 FiberGuide** System The FIBERRUNNER 12x4 Cable Routing System to ADC 4x12 FiberGuide Adapter when used with the FIBERRUNNER 12x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 12x4 Cable Routing System to transition into or out of the ADC 4x12 FiberGuide System. The adapter slides into the rib structure of the ADC 4x12 FiberGuide Channel and is secured with five (5) ¼-20x" Hex Head Cap Screws, five (5) .312"x.734" Type A Plain Washers and five (5) ¼-20 Hex Nuts (included). The FIBERRUNNER 12x4 Cable Routing System to ADC 4x12 FiberGuide Adapter can be easily installed as follows: 1. Insert one (1) of the ¼-20x" Hex Head Cap Screws into each of the mounting holes on the adapter. Be sure that all five (5) of the cap screws are pointing outward away from the adapter. With the cap screws in place, slide the adapter into the rib structure of the ADC 4x4 FiberGuide Channel until the adapter is completely seated against the channel section. Note that the rib structure of the ADC channel will hold the cap screws in place. ADC 4x12 FiberGuide Channel FIBERRUNNER 12x4 Cable Routing System to ADC 4x12 FiberGuide Adapter (FRADC12X4BL) ¼-20x" Hex Head Cap Screw (Typical: 5 Places) 2. Install one (1) of the .312"x.734" Type A Plain Washers and thread one (1) of the ¼-20 Hex Nuts on to each of the cap screws and hand tighten. Tighten all five (5) of the ¼-20 Hex Nuts using the FIBERRUNNER 7/16" Nut Driver to secure the adapter installation. Please note that any standard 7/16" nut driver will work as well. If the use of hand tools is not preferred a nonmagnetic FIBERRUNNER 7/16" Nut Driver Bit is also available. © 2005 PANDUIT Corp. ¼-20 Hex Nut (Typical: 5 Places) .312"x.734" Type A Plain Washer (Typical: 5 Places) 9-16 FIBERRUNNER 7/16" Nut Driver (FR716DR) ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 3. With the adapter secure to the ADC 4x12 FiberGuide Channel, align the extended ribs of the FIBERRUNNER 12x4 QUIKLOCK Coupler with the FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 12x4 QUIKLOCKTM Coupler (FRBC12X4**) 4. With the FIBERRUNNER 12x4 QUIKLOCK Coupler in place, a section of FIBERRUNNER 12x4 Channel and/or any FIBERRUNNER 12x4 fitting can be installed to continue the fiber pathway. FIBERRUNNER 12x4 Channel or Fitting (FR12X4**6 shown) Part numbers described in this section: FRADC12X4BL - FIBERRUNNER 12x4 Cable Routing System to ADC 4x12 FiberGuide Adapter Part numbers referenced in this section: FRBC12X4** - FIBERRUNNER 12x4 QUIKLOCK Coupler FR12X4**6 FIBERRUNNER 12x4 Channel FR716DR FIBERRUNNER 7/16" Nut Driver FR716BIT FIBERRUNNER 7/16" Nut Driver Bit When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * ADC is a registered trademark of ADC Telecommunications, Inc. ** FiberGuide is a registered trademark of ADC Telecommunications, Inc. © 2005 PANDUIT Corp. 9-17 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 1.8 FIBERRUNNER 12x4 Cable Routing System to Newton* 4x12 Fiber Cable Management System The FIBERRUNNER 12x4 Cable Routing System to Newton 4x12 Adapter when used with the FIBERRUNNER 12x4 QUIKLOCKTM Coupler allows the FIBERRUNNER 12x4 Cable Routing System to transition into or out of the Newton 4x12 Fiber Cable Management System. The adapter slides over the Newton 4x12 Solid Wall Channel and is secured with the five (5) ¼-20x" Nylon Phillips Binder Head Screws and five (5) ¼-20 Nylon Deco Wing Nuts (included). The FIBERRUNNER 12x4 Cable Routing System to Newton 4x12 Adapter can be easily installed as follows: 1. Align the profile of the Newton 4x12 Solid Wall Channel with the inside of the adapter. Slide the adapter over the end of the channel until the adapter is completely seated against the channel profile. FIBERRUNNER 12x4 Cable Routing System to Newton 4x12 Adapter (FRNWT12) Newton 4x12 Solid Wall Channel 2. With the adapter held in place, mark all five (5) mounting hole locations of the adapter on to the channel section. Remove the adapter and with a 9/32" diameter drill bit create five (5) mounting holes in the channel. Please note that before the drilling operation begins, that all cables, etc. are out of the path of the drilling bit. 9/32" Drill Bit 3. Reattach the adapter and realign all five (5) of the mounting holes. With the adapter held in place, insert one (1) of the ¼-20x" Nylon Phillips Binder Head Screws through each of the mounting holes from the inside of the channel. Be sure that all five (5) of the binder head screws are pointing outward away from the adapter. Thread one (1) of the ¼-20 Nylon Deco Wing Nuts on to each of the binder head screws and hand tighten. ¼-20x" Nylon Phillips Binder Head Screw (Typical: 5 Places) © 2005 PANDUIT Corp. 9-18 ALL RIGHTS RESERVED PANDUIT ® FIBERRUNNER ® Cable Routing System Application Guide Section 9 ¼-20 Nylon Deco Wing Nut (Typical: 5 Places) 4. With the adapter secure to the Newton 4x12 Solid Wall Channel, align the extended ribs of the FIBERRUNNER 12x4 QUIKLOCKTM with the FIBERRUNNER Cable Routing System side of the adapter. Once aligned, push the adapter and the coupler together until the adapter is seated against the inner rib of the coupler. Please note that the slight amount of resistance that is felt is normal, indicating that the metal barbs of the coupler have engaged the surface of the adapter. FIBERRUNNER 12x4 QUIKLOCK Coupler (FRBC12X4**) 5. With the FIBERRUNNER 12x4 QUIKLOCK Coupler in place, a section of FIBERRUNNER 12x4 Channel and/or any FIBERRUNNER 12x4 Fitting can be installed to continue the fiber pathway. FiberRunner 12x4 Channel or Fitting (FR12X4**6 shown) Part numbers described in this section: FRNWT12 - FIBERRUNNER 12x4 Cable Routing System to Newton 4x12 Adapter Part numbers referenced in this section: FRBC12X4** - FIBERRUNNER 12x4 QUIKLOCK Coupler FR12X4**6 FIBERRUNNER 12x4 Channel When ordering, replace ** in the part number with YL for Yellow, OR for Orange or BL for Black * Newton is a trademark of Newton Instrument Company, Inc. © 2005 PANDUIT Corp. 9-19 ALL RIGHTS RESERVEDAcrobat Distiller 7.0.5 (Windows)