E. C. LIST/变更履历表
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 12 Pages, 758.95KB
Document DEVICE REPORT0000000089HKA04520023-2K SHENZHEN HUNTKEY ELECTRIC CO., LTD E. C. LIST/ Rev. Description of Change/ Before/ After/ 1 Original Release --- Changed Date/ ECN No. 2019-01-16 --- Page 2 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD 1 Electrical Specification/ 1.1SCOPE/ The document details the electrical, mechanical and environmental specifications of a SMPS, the power supply provides 45 W continuous output power. 45W(),. The power supply shall meet the RoHS requirements. RoHS . Description/ SMPS Adaptor(Wall mount)/ SMPS Adaptor(Desk-top)/ Open Frame/ SMPS Unit (With Case)/ Others/ 1.2 Input Characteristics/ 1.2.1. Input Voltage & Frequency/ The range of input voltage is from 90Vac to 264Vac with a single phase. 90Vac 264Vac, . Minimum/ Rating/ Maximum/ Input Voltage/ 90Vac 100Vac~240Vac 264Vac Input Frequency/ 47Hz 60Hz/50Hz 63Hz 1.2.2. Input AC Current/ 1.2Amax. @ 90Vac input & Full load/ 90Vac 1.2A 1.3.3. Inrush Current (cold start)/() Power supply inrush current shall be less than the ratings of its critical components (including bulk rectifiers, fuses, and surge limiting device) under all conditions of line voltage of Section 2.1. 2.1 ( 1.2.4. Average Efficiency / Test condition after heat-up 30minutes/ 30 Input Voltage Range Output Voltage Average Efficiency Load Condition 5V 81.84 25%,50%,75%,100% 9V 87.30 25%,50%,75%,100% 115VAC and 230VAC 12V 88.30 25%,50%,75%,100% 15V 88.85 25%,50%,75%,100% 20V 88.85 1.2.5. No-Load Input Power Dissipation/ 25%,50%,75%,100% Test condition after heat-up 30minutes/ 30 While input at the 115Vac and 230Vac, output voltage is 5V and no load, the input power loss must be less than 0.075W. Page 3 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD 115V 230Vac 5V 0.075W. 1.3 Output Characteristics/ 1.3.1.Static Output Characteristics <Vo & R+N>/<&+> Output Rated Load/ Output Range R+N Remark Rating Min. Load Max. Load +5V 0A 3.0A 4.75V ~ 5.25V 150mVp-p +9V 0A 3.0A 8.55V~9.45V 200mVp-p +12V 0A 3.0A 11.4V~12.6V 200mVp-p +15V 0A 3.0A 14.25V~15.75V 200mVp-p +20V 0A 2.25A 19V ~ 21V 200mVp-p Ripple & Noise: Tested by a oscilloscope using 20MHz bandwidth and the output is paralleled a 0.1uF ceramic capacitor and a 10uF electrolysis capacitor. (Under the input Voltage 100~240Vac) : 20MHz , 0.1uF 10uF ( 100~240Vac) 1.3.2.Line/ Load Regulation// Output Load Condition/ Line Regulation Load Regulation Remark Voltage Min. Load Max. Load +5V 0A 3A ± 5% ± 5% +9V 0A 3A ± 5% ± 5% +12V 0A 3A ± 5% ± 5% +15V 0A 3A ± 5% ± 5% +20V 0A 2.25A ± 5% ± 5% 1.3.3.Turn - on Delay Time/ 3S max. @90Vac input & Full load/ 90Vac 3S 1.3.4. Hold-up Time/ 10mS min. @ Full load &115Vac/60Hz input turn off at worst case 115Vac/60Hz , 10mS 1.3.5.Rise Time/ 30mS max. @ Full load/ 30mS 1.3.6.Fall Time/ 20mS max. @ Full load/ 20mS 1.3.7.Output Overshoot / Undershoot// 10% max. When the power on or off/ 10% 1.3.8.Output Load Transient Response/ +5VOutput voltage is within 4.5~5.5V while the load step is from 25% to 50% to 25% of max load or 50% to 75% to 50% of max load, R/S: 0.2A/uS, periods: 4mS, the maximum Page 4 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD of comeback time is 200uS.Output Overshoot is less then ±5%. 5V 4.5-5.5V ,: 25% 50% 25% 50% 75% 50%,: 0.2A/uS,4mS, 200uS±5%. +9VOutput voltage is within 8.55V~9.45V while the load step is from 25% to 50% to 25% of max load or 50% to 75% to 50% of max load, R/S: 0.2A/uS, periods: 4mS, the maximum of comeback time is 200uS.Output Overshoot is less then ±5%. 9V 8.55V~9.45V ,: 25% 50% 25% 50% 75% 50%,: 0.2A/uS,4mS, 200uS±5%. +12VOutput voltage is within11.4V~12.6Vwhile the load step is from 25% to 50% to 25% of max load or 50% to 75% to 50% of max load, R/S: 0.2A/uS, periods: 4mS, the maximum of comeback time is 200uS.Output Overshoot is less then ±5%. 12V 11.4V~12.6V ,: 25% 50% 25% 50% 75% 50%,: 0.2A/uS,4mS, 200uS±5%. +15VOutput voltage is within 14.25V~15.75V while the load step is from 25% to 50% to 25% of max load or 50% to 75% to 50% of max load, R/S: 0.2A/uS, periods: 4mS, the maximum of comeback time is 200uS.Output Overshoot is less then ±5%. 15V 14.25V~15.75V ,: 25% 50% 25% 50% 75% 50%,: 0.2A/uS,4mS, 200uS±5%. +20VOutput voltage is within 19V~21V while the load step is from 25% to 50% to 25% of max load or 50% to 75% to 50% of max load, R/S: 0.2A/uS, periods: 4mS, the maximum of comeback time is 200uS.Output Overshoot is less then ±5%. 20V 19V~21V ,: 25% 50% 25% 50% 75% 50%,: 0.2A/uS,4mS, 200uS±5%. 1.3.9.Capacitance Load/ While input 115Vac/230Vac & full load, and the output is paralleled a 2000uF electrolysis capacitor, the output voltage shall be single assurgent 115Vac/230Vac 2000uF 1.4Protection Requirements/ 1.4.1.Over Current Protection/ OCP Point Limited: not more than 130% of MAX. load.: 130% The output shall hiccup when the over current applied to the output, and shall be Self-recovery when the fault condition is removed ,,, Page 5 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD 1.4.2.Short Circuit Protection/ The input power shall decrease when the output is short to GND; the power supply shall not damage, and shall be self-recovery when the fault condition is removed ,,, 1.4.3.Over Voltage Protection/ 5V output-OVP Point Limited: Maximum 7.5V 5V 7.5V 9V output-OVP Point Limited: Maximum 13V. 9V 13V 12V output-OVP Point Limited: Maximum 16V. 9V 16V 15V output-OVP Point Limited: Maximum 20V 15V 20V 20V output-OVP Point Limited: Maximum 26V 20V 26V The power supply shall be Latch off mode, when the output is over voltage, and the power supply shall not be damaged. ,. 2Environment Requirements/ 2.1Operating Temperature and Relative Humidity/ 0 to +40 5%RH to 95%RH Sea level shall below 5,000 meter / 5000M 2.2Storage Temperature and Relative Humidity/ -20 to +70 5%RH to 95%RH non-condensing @ Sea level shall below 5,000 meter 5,000 -20 +70, 5%RH to 95%RH 3Reliability Requirements/ 3.1.Vibration/ 5 to 500Hz sweep at a shift gears for 20 minute for each of the perpendicular axes X, Y, Z thereinto :acceleration frequency for 10 m2/s3 at 5~10HZ; acceleration frequency for 3 m2/s3 at 10~200HZ; acceleration frequency for 1 m2/s3 at 200~500HZ : 5 to 500Hz , X, Y, Z 20 ,: 5~10HZ 10 m2/s3 10~200HZ 3 m2/s3200~500HZ 1 m2/s3 3.2.Drop in/ 6 Surfaces each once, Height: 80cm, on the wood floor 6 , : 80 , 3.3.MTBF Qualification/ The MTBF shall be at least 50,000hours at 25, Full load and normal input condition : 50,000 ,25 Page 6 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD 3.4.The lifetime electrolyte capacitor/ The lifetime of electrolyte capacitor shall be at least 26280hours at 30of full load and 115Vac/230Vac input condition 26280 ,30 115Vac/230Vac 4EMI/EMS Standards/EMI/EMS 4.1.EMI Standards/EMI EN 55032: 2015 EN 61000-3-2:2014 EN 61000-3-3:2013 4.2.EMS Standards/EMS Electrostatic Discharge(ESD): 15kV air discharge, 8kV contact EN 61000-4-2:2009 discharge EN61000-4-3 : 2006+ Radio-Frequency Electromagnetic Field Susceptibility Test-RS A1 : 2008 + A2: 2010 EN61000-4-4: 2012 Electrical Fast Transient/Burst-EFT ±2kV EN 61000-4-5:2014 Surge Immunity Test: Differential mode ±2kV,Common mode ±4kV EN61000-4-6: 2014 Conducted Radio Frequency Disturbances Test-CS EN61000-4-8: 2010 Power Frequency Magnetic Field Test EN61000-4-11:2004 Voltage Dips 5Safety Standards/ 5.1.Dielectric Strength(Hi-pot)/() Primary to Secondary: 3000Vac / 3.5mA / 60 seconds Or 4242Vdc / 3.5mA / 60 seconds : 3000Vac / 3.5mA / 60 4242Vdc / 3.5mA / 60 5.2.Leakage Current/ 0.25mAmax. at 264Vac / 50Hz input/ 264Vac/50Hz 0.25mA 5.3.Insulation Resistance/ 100M min. @ primary to secondary add a 500Vdc test voltage 500Vdc , 100M Page 7 Q01-731-00-12-P2 1 SHENZHEN HUNTKEY ELECTRIC CO., LTD 5.4.Regulatory Standards/ Type UL/CUL TUV CCC CE Country USA Europe China Europe Standard UL60950-1 EN60950-1 GB4943 EN60950-1 Type PSB PSE NOM GOST Country Standard Singapore IEC60950-1 Japan J60950 Mexico NOM-001 Russia MEK60950 Page 8 Q01-731-00-12-P2 1 6Mach. Outline Drawing/ SHENZHEN HUNTKEY ELECTRIC CO., LTD Page 9 Q01-731-00-12-P2 1 7Label Drawing/ SHENZHEN HUNTKEY ELECTRIC CO., LTD 8Package Drawing/ 9Circuit Schematic Drawing/ 10PCB Drawing/PCB 11Bill Of Material (BOM)/ 12Product Picture/ 13Bill Of Material (BOM)/() Page 10 Q01-731-00-12-P2 1 SHENZHEN, China, August 30, 2019 Huntkey, a leading global provider of power solutions, has recently released its 45W charger to global markets. The charger is integrated with a USB-C port, and features PD3.0 charging abilities that can charge electronic devices with a faster charging speed than a conventional charger. The charger is universally compatible with PD3.0 technologies, which makes it suite for a wide range of devices that equipped with USB-C interface such as smart phones, tablets, notebooks. The double-chip inside the 45W charger can properly adapt a worldwide voltage input from 100V to 240V. It means you can use it in any country as long as the charger can plug into the local socket. Besides the wide voltage feature, the 45W Huntkey USB-C charger can intelligently control the charging rates and match a proper rate for smart phones or tablets, keep the battery durable all the time. The 45W charger is accredited with UL, and also is equipped with all-round protections including Over Charge Protection (OCP), Over Heat Protection (OHP) and Short Circuit Protection (SCP). Before launching the charger to the market, Huntkey conducted an experimental test to demonstrate its superior charging speed. It can charge any common mobile phones from 1% of the mobile battery to 50% of the mobile battery within 30 minutes. About Huntkey Huntkey, founded in 1995 and headquartered in Shenzhen, is a member of The International Power Supply Manufacturer's Association (PSMA) and a member of The China Power Supply Society (CPSS). With branch companies in the USA, Japan and other areas, and cooperating factories in Brazil, Argentina, India and other countries, Huntkey has specialized in the development, design, and manufacturing of PC power supplies, industrial power supplies, surge protectors, adapters and chargers for many years. With its own technologies and manufacturing strength, Huntkey has served Lenovo, Huawei, Haier, DELL, ZTE, Bestbuy and many other large enterprises for years, and has received unanimous recognition and trust from most of its customers. SHENZHEN, China, November 16, 2019 Huntkey, a global leading provider of power solutions, has recently released its new product the 45W USB-C charger, which is compatible with multiple devices including smart phones, tablets and notebook. In order to keep pace with the trend that USB-C is slowly replacing the previous USB types, Huntkey has been consistently investing on and developing USB-C products to meet the increasing market demands. As one of the key products of Huntkey, the 45W USB-C charger is durable and reliable, and designed with pocket-sized that easy for carry and convenient use. The 45W USB-C charger is able to output 5V, 9V, 12V, 15V and 20V power to different devices. It is equipped with a USD-C port that allows the users to connect it to the electronic devices in either way, which kills off the irritating problem of connection. Its intelligent charging allows the users to charge multiple devices. In the package, it is paired with a 1.8m USB-C cable. It is built with all-round protections including SCP (Short Circuit Protection), OVP (Over Voltage Protection) and OCP (Over Current Protection). Not only will it protect itself, but also keep the charging devices safe under any circumstances.