Antenna Specification

Dongguan Lingdu Electronic Technology Co.,Ltd K06 IP Camera 2BEAP-K06 2BEAPK06 k06

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 11 Pages, 977.27KB

Document DEVICE REPORTGetApplicationAttachment.html?id=7383370
SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD



:

Specification For Approval

: Customer:

 Dongguan Lingdu Electronic Technology Co.,Ltd

: Customer:

 SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

: 1124-0000500-001

K06-WIFI-V1.0 GYF :
2023-10-24

WiFi K06FPC 

3M9471 

: 

: K06

L=115mm,1.13mm

():

():

 

  2024.01.26

: 16  D  606 

Tel: 0755-26702159

Fax: 0755-26702585

http:// www.gyfgpsbd.com/

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD
Catalogue
1. Specifications
1.1  Electrical specifications
2.  Matching circuit diagram 3.  Structural form
3.1  Antenna composition
4. Testing equipment 5.VSWR  VSWR test connection
5.1  Testing Connection
6. Testing
6.1 Testing Site 6.2 Testing instruments 6.3 Test data
7. Drawing specifications
7.1 Drawings 7.2 Sample size testing 7.3 Bill of Materials
8. Reliability testing
8.1 Reliability Test Report 8.2 Product Storage Instructions
9.  Working temperature 10.  Antenna image
2 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD
1. specifications
1.1  Electrical specifications

specification
2.4GHz FPC WiFi

GYF PNO.
K06-WIFI-V1.0 GYF 2023-10-24

2.  Matching circuit diagram

3. Structural form
3.1  Antenna composition The antenna is mainly composed of a flexible printed circuit board and coaxial lines.
4.  Testing equipment

5 .VSWR  VSWR test connection
5.1 Test Connection:
3 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD
The VSWR testing device is sequentially connected as follows: R&S ZVL network analyzer  test line  test fixture
6. test
6.1 Testing venue: Guangyuan Microwave darkroom. The testing frequency range is 400MHz to 6GHz, the quiet zone range is 50cm circumference, and the reflectivity is less than -50 dB.
6.2 Testing instruments: Agilent5071B, CMW500, Agilent8960 E5515C, standard horn antenna, 24 probe OTA microwave darkroom testing system, printer, etc
6.3 Test data:
4 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD
2460MHz
5 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD
7. Drawing specifications
7.1  Drawings
6 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

7.2  Sample size testing

Modle

K06

NO. Spec.(mm)

1

1

23.10 23.08

2

13.00 13.05

3

115.00 115.19

4

1.13

1.12

5

6

7

8

9

10

11 12 13 14 15 16 17 18 19 20 21 22 23

K06-WIFI-V1.0 GYF PN.
2023-10-24

2 23.12 13.02 115.22 1.13

Test data(mm)

3 23.11

4 23.09

12.98

13.01

115.15

115.17

1.11

1.12

Date

2024.01.26

5 23.13 13.04 115.23 1.13

Result
OK OK OK OK

remark

7 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

7.3  BOM

Modle
NO. 1 2 3 4 5 6 8 9 10 11 12 13 14 15 16 17 18 19 20

K06

PN.

Name fpc coaxial line

material 
Cu

BOM

K06-WIFI-V1.0 GYF 2023-10-24

DATE

Spec.

23.10*13.00mm

1.13 black 115mm

2024.01.26
usage 1 1

8 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

8. Reliability test

8.1  Reliability test report

Modle Qty

K06 15pcs

K06-WIFI-V1.0 GYF

PN

Date

2023-10-24

2024.01.26

Test items

Test standards

Qty

(1) Test temperature: Salt water test at 35 ± 2 ; Pressure bucket 47  ±1

Salt spray corrosion
test

(2) Test conditions/methods: Salt water concentration above 5%, solution pH value: 6.5~7.2, air pressure: 1.0~1.2kg/c , test time set according to product requirements

5pcs

(3) Test completed: After 2 hours, observe the oxidation and discoloration of the surface of the product, as well as the appearance of the coating peeling off (1) Temperature: -30  (-25  pilot stage)

(2) Test time: 20 hours/Packaging condition: Unpacked

Low temperatur e testing

(3) The tested product is not turned on and placed in a high and low temperature test box. The temperature inside the box is adjusted to 25  and the humidity is 65%. After insulation for 1 hour, it is cooled to -30  within 1 hour. The humidity is turned off, and after insulation for 20 hours, it is heated for 1 hour to room temperature. Performance testing is conducted after 2 hours. Appearance and structure: The antenna surface should have no defects, and there should be no deformation, warping, or

5pcs

9 / 11

Result

Test time

OK

48H

OK

20H

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

damage to the antenna. The performance should be normal, and the standing wave ratio should not exceed 10% of the product standard (1) Temperature:+70  (+65  pilot stage) Humidity: 85% (80% - pilot stage)

(2) Test time: 20 hours/Packaging condition: Unpacked

(3) The tested product is not turned on

and placed in a high and low

temperature test box. The temperature

inside the box is adjusted to 25  and

High

the humidity is 65%. After insulation

temperatur for 1 hour, the temperature is raised 5pcs

OK

e testing to+70  and the humidity is 85%.

After insulation for 20 hours, the

temperature is lowered to room

temperature for 1 hour. Performance

testing is conducted after 2 hours.

Appearance and structure: The antenna

surface should have no defects, and

there should be no deformation,

warping, or damage to the antenna. The

performance should be normal, and the

standing wave ratio should not exceed

10% of the product standard

8.2  Product Storage Instructions 1. The exposed part of the gold finger conductor needs to undergo surface coating (anti rust) treatment, such as gold plating/plating, OSP, tin plating, etc. The storage environment needs to avoid corrosive gases. 2. The antenna temperature needs to be controlled at 21-38  , and the humidity needs to be controlled at 50-70%. Excessive temperature can cause the 3M adhesive to melt, resulting in a decrease in antenna adhesion. 3. It is recommended that if the initial bonding temperature is below 10 , it is not suitable for bonding, as the adhesive at this time is too hard to firmly adhere to the object; However, if it has already been bonded, the adhesive strength at low temperatures is also satisfactory. 4. Under conditions of 21  and 50% relative humidity, the original packaging state has a shelf life of 24 months from the date of production.

10 / 11

SHENZHEN GUANGYUANFA ELECTRONIC CO.,LTD

9. Work temperature

Parts FPC body

Temperature -50~280

10. Antenna image

11 / 11



Related FCC IDs:

Search Any Device: