AN-PS0030-Coolset F3 ELJ Latch Jitter design guide V11 1Nov2009

koks

ICE3Axx65ELJ

Infineon-Design guide integrated power stage CoolSET F3 ICE3AXX65ELJ-AN-v01 01-EN

Solved: ICE2A265 - Infineon Developer Community

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 18 Pages, 3.06MB

Document DEVICE REPORTInfineon-Design guide integrated power stage CoolSET F3 ICE3AXX65ELJ-AN-v01 01-EN
Application Note, V1.1, November 2009
ICE3Axx65ELJ
CoolSET®-F3 Latch & Jitter version Design Guide
Power Management & Supply
Never stop thinking.

Edition 2009-11-01 Published by Infineon Technologies Asia Pacific, 8 Kallang Sector, 349282 Singapore, Singapore © Infineon Technologies AP 2008. All Rights Reserved.
Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein.
Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com).
Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

ICE3Axx65ELJ

Revision History: Previous Version: Page 9

2009-11 V1.0 Subjects (major changes since last revision) Add precaution for the start up sequence.

V1.1

ICE3Axx65ELJ CoolSET®-F3 Latch & Jitter version Design Guide: License to Infineon Technologies Asia Pacific Pte Ltd
Kyaw Zin Min Kok Siu Kam Eric
We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: [email protected]

AN-PS0030

ICE3Axx65ELJ

Table of Contents

Page

1
2
3
4
5
6 6.1 6.2 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.4 6.5 6.6 6.6.1 6.6.2 6.6.3
7
8
9
10

Introduction ...................................................................................................................................5
List of Features .............................................................................................................................5
Package & pin assignment...........................................................................................................6
Block Diagram ...............................................................................................................................7
Typical Application Circuit...........................................................................................................8
Function Description ....................................................................................................................9 Startup Cell......................................................................................................................................9 Soft Start and Normal Operation.....................................................................................................9 Active Burst Mode .........................................................................................................................10 Entering Active Burst Mode...........................................................................................................10 Working in Active Burst Mode .......................................................................................................11 Leaving Active Burst Mode ...........................................................................................................12 VCC supply during burst mode .......................................................................................................13 Switching frequency modulation ...................................................................................................13 Propagation delay compensation..................................................................................................14 Protection Features .......................................................................................................................14 Auto Restart Mode ........................................................................................................................15 Latched Off Mode..........................................................................................................................15 Blanking Time for over load protection .........................................................................................16
Layout Consideration .................................................................................................................17
CoolSET®-F3 ICE3Axx65ELJ product list .................................................................................17
Useful formula & external component design .........................................................................17
References ...................................................................................................................................18

Application Note

4

2009-11-01

ICE3Axx65ELJ

1

Introduction

The ICE3Axx65ELJ is the further development of the 3rd generation CoolSET®. It is a PWM controller with power MOSFET together in a DIP-8 package. The switching frequency is running at 100 KHz and it targets for DVD player, set-top box, portable game console, auxiliary power supply, etc.

The ICE3Axx65ELJ adopts the BiCMOS technology and provides a wider Vcc operating range up to 26V. It inherits the proven good features of CoolSET®-F3 such as the active burst mode achieving the lowest standby power, the propagation delay compensation making the most precise current limit control in wide input voltage range, etc. In addition, it also adds on some useful features such as built-in soft start time, builtin basic with extendable blanking time for over load protection and built-in switching frequency modulation ( frequency jittering ), external latch enable, etc. Furthermore, it has implemented with enhanced noise immunity feature such that it can pass 20KV ESD test (contact discharge) and 8KV lightning surge test.

In this application note, functions of the device are described in detail with formula and its performance is shown with test waveforms. The description of other related information such as DCM/CCM mode operating principles and slope compensation and the detailed design procedure are shown in the application note "ANSMPS-ICE2xXXX-1".

2

List of Features

650V avalanche rugged CoolMOS® with built in switchable Startup Cell Active Burst Mode for lowest Standby Power BiCMOS technology provide wide Vcc voltage range Fast load jump response in Active Burst Mode 100kHz fixed switching frequency with frequency modulation Latched Off mode for over temperature, Vcc over voltage and short winding protection Auto Restart Mode for over load protection, Open Loop protection and Vcc under voltage protection Built-in soft start time Built-in and extendable blanking window for short duration peak power External latch enable feature Propagation delay compensation tighten the maximum power control between high line and low line Switching frequency modulation and soft gate driving for low EMI Robustness to system noise such as ESD, lightning surge, etc.

Application Note

5

2009-11-01

ICE3Axx65ELJ

3

Package & pin assignment

The package for CoolSET®-F3 Latch and Jitter mode product is DIP-8.

BL

1

8

GND

FB

2

7

VCC

CS

3

6

n.c.

Drain

4

5

Drain

Pin

Symbol

Function

1

BL

extended Blanking & Latch enable

2

FB

FeedBack

3

CS

Current Sense / 650V1 CoolMOS® Source

4

Drain 650V1 CoolMOS® Drain

5

Drain 650V1 CoolMOS® Drain

6

n.c.

not connected

7

VCC controller supply Voltage

8

GND controller GrouND

Figure 1 DIP-8 package

1 Tj=110°C

Application Note

6

2009-11-01

4

Block Diagram

ICE3Axx65ELJ

Figure 2 Block Diagram of CoolSET®-F3 ICE3Axx65ELJ

Application Note

7

2009-11-01

5

Typical Application Circuit

ICE3Axx65ELJ

Figure 3 Typical application circuit with CoolSET®-F3, ICE3A1065ELJ 15W 5V

Application Note

8

2009-11-01

ICE3Axx65ELJ

6

Function Description

6.1

Startup Cell

The Startup Cell delivers a constant charge current of IVCCcharge3=0.7mA to charge up the VCC capacitor CVcc at VCC pin. When VCC exceeds the on-threshold VCCon=18V, the bias circuit is switched on. The Startup Cell is switched off to reduce the power loss. The startup delay time, tDELAY, is independent from the AC line input voltage. It can be estimated by the Equation(1).

t DELAY

= VVCCon  CVcc IVCCcharg e3

(1)

Figure 4 shows the startup time delay at 85VAC input. ( Pls refer to the datasheet for the symbol used in the equation )

Vds
0.6s Vcc
Vfb

Figure 4

The startup delay time at AC line input voltage of 85VAC

Precaution : For a typical application, start up should be VCC ramps up first, other pin (such as FB pin) voltage will follow VCC voltage to ramp up. It is recommended not to have any voltage on other pins (such as FB; BA and CS) before VCC ramps up.

6.2

Soft Start and Normal Operation

When the IC is turned on after the Startup Delay time, a digital soft start circuit is activated. A gradually increased soft start voltage is released by the digital soft start circuit, which in turn increases the duty cycle accordingly. The soft start control voltage is increased with the increasing of count number in the digital counter of the soft start circuit. The soft start time is set at 20ms. When the soft start time ends, IC goes into normal mode and the duty cycle is dependent on the FB signal. Figure 5 shows the soft start behaviour at 85VAC input. It can be seen that the primary peak current slowly increase to the maximum in the soft start period. After soft start stage, IC goes into normal operation with the conventional primary peak current control scheme. Please refer to "AN-SMPS-ICE2xXXXX-1" for the details of normal operation.

Application Note

9

2009-11-01

ICE3Axx65ELJ

Vout Vcc
Vfb

20ms

1V

Vcs

Figure 5 Soft start at AC line input voltage of 85VAC

6.3

Active Burst Mode

The IC provides an Active Burst Mode function at no load or low load conditions to enable the system to achieve the lowest standby power requirement of less than 100mW. Active Burst Mode means the IC is always in the active state and can therefore immediately response to any changes on the FB signal, VFB.

6.3.1 Entering Active Burst Mode

Because of the current mode control scheme, the feedback voltage VFB actually controls the power delivery to output. When the output load is getting lower, the feedback voltage VFB drops. If it stays below 1.35V for a period of 20ms, the IC enters the burst mode operation. The threshold power to enter burst mode can be
estimated in Equation(2).

PBURST _ enter

= 0.5  LP

 (VFBC5 - VOffset-Ramp ) 2  Rsense  AV

f SW

(2)

where, LP is the transformer primary inductance, VFBC5=1.35V is the feedback voltage at which the system starts to burst, VOffset-Ramp=0.6V is the maximum level of the internal Voltage Ramp on which the amplified current ramp signal of the PWM-OP is superimposed, AV=3.2 is the internal PWM-OP gain, Rsense is the current sense resistor, fSW is the switching frequency. Figure 6 shows the test waveform with the load drop from full load to light load. After blanking time IC goes into burst mode.

Application Note

10

2009-11-01

ICE3Axx65ELJ

Vds Vout
19.3ms
Vfb

Figure 6 Entering Burst Mode

6.3.2 Working in Active Burst Mode

During active burst mode, the IC is constantly monitoring the output voltage by feedback pin, VFB, which controls burst duty cycle and burst frequency. The burst "on" starts when VFB reaches 3.61V and stops when VFB is down to 3.0V. During burst "on", the primary current limit is set to only 31% of maximum peak current (VCS=0.31V) to reduce the conduction losses and to avoid audible noise. The FB voltage is changing like a saw-tooth between 3.0V and 3.61V.The corresponding secondary output ripple (peak to peak) is regulated in
Equation(3).

Vout _ ripple _ pp

=

RFB

Ropto  Gopto  GTL431

 VFB

(3)

where, Ropto is the resistor in series with opto-coupler at the secondary side to limit the opto-coupler current, RFB is the IC internal pull up resistor connected to FB Pin (refer to Figure 2), Gopto is the current transfer gain of opto-coupler, GTL431 is the voltage transfer gain between the comparator TL431 output and Vout, VFB=3.61-3.0=0.61V is the saw-tooth voltage on the VFB during burst operation.
The leaving burst power threshold, i.e. maximum power to be handled during burst operation is showed in Equation(4).

Pburst _ max

= 0.5  LP  (0.31 i peak _ max ) 2 

f SW

=

0.5 

LP

 (0.31 VCS _ max Rsense

)2



f SW

= 0.0961 Pmax

(4)

Where, ipeak_max is the maximum primary peak current, VCS_max is the cycle by cycle current limit threshold at CS pin, Pmax is the maximum output power of the power supply. It can be seen that the maximum power in burst mode is around 9.61% of Pmax. Figure 7 shows the waveform of burst mode at light load. It can be seen that the burst ripple is well regulated to be 40mV and it is independent on the output power.

Application Note

11

2009-11-01

ICE3Axx65ELJ

Vds Vout
Vfb

40mV

Figure 7 In Burst Mode at light load
6.3.3 Leaving Active Burst Mode
When the output load is increasing to be higher than Pburst_max, Vout will drop a little bit and VFB will rise up fast to 4.5V. The system leaves burst mode immediately when VFB reaches 4.5V. Once system leaves burst mode, the current sense voltage limit, VCS_MAX, is released to 1V, the feedback voltage VFB swings back to the required level. The timing diagram of leaving burst mode is shown in Figure 8.
4.5V 3.61V
VFB
3.0V

Vout Vout_AV

Vout_drop_max

1V

VCS 0.31V
Figure 8 the timing diagram of leaving burst mode

The maximum Vout drop during the mode transition is estimated in Equation(5).

Vout _ drop _ max

=

RFB

Ropto  Gopto  GTL431

 (4.5 -

3.0 +23.61)

=

1.195  Ropto RFB  Gopto  GTL431

Application Note

12

(5) 2009-11-01

ICE3Axx65ELJ
Figure 9 shows the waveform to leave burst mode with load jump from light load to full load. The output voltage drop during the transition is about 140mV.
Vout 140mV
Vfb

Vcs

Figure 9 Scope waveform of leaving burst mode

6.3.4 VCC supply during burst mode
The supply voltage for VCC has to be designed so that it always stays above VVCCoff limit during burst mode, especially at no load. If there is a substantial high voltage at VCC pin during maximum load operation, it should add a voltage clamp circuit to absorb the high surge voltage. The circuit configuration for VCC in Figure 3, which consists of C5, R3, R5, R6, ZD1 and C6, is to ensure the VCC will not exceed 26V under any operation conditions.

6.4

Switching frequency modulation

The IC is running at fixed frequency of 100KHz with jittering frequency at +/-4KHz in a switching modulation period of 4ms. This kind of frequency modulation can effectively help to obtain a low EMI level. The measured jittering frequency is 94.5KHz ~ 102.06KHz ( Figure 10 ).

Vds
102.06KH 94.5KHz

Figure 10 Switching frequency jittering

Application Note

13

2009-11-01

ICE3Axx65ELJ

6.5

Propagation delay compensation

It is observed that the maximum input power will change with input voltage. This is due to the propagation delay of the controller in different dI/dt of the input voltage. The power difference can be as high as >14% between high line and low line. Starting from our 2nd generation, a propagation delay compensation network is implemented so that the power difference is greatly reduced to best around 2%. A measured result for this 15W demo boards shows an output power difference of around +/-3.25% between 85Vac and 269 Vac input. Figure 11 shows the propagation delay compensation curve implemented to the IC. This function applies to discontinuous conduction mode flyback converter only.

Sense V

V
1,3 1,25
1,2 1,15
1,1 1,05
1 0,95
0,9 0

with compensation

without compensation

0,2 0,4 0,6 0,8

1 1,2 1,4 1,6 1,8
dVSense dt

2V µs

Figure 11 Propagation delay compensation curve

6.6

Protection Features

The IC provides several protection features which lead to the Auto Restart Mode or Latched off mode. The following table lists the conditions of the system faults and the associate protection mode.

Protection functions

Failure condition

VCC Over voltage
Over temperature ( controller ) Short Winding/ Short Diode External latch enable Output Overload / Output Short Circuit

VCC > 24V and VFB > 4.5V
TJ > 130OC
VCS > 1.66V VBL < 0.1V VFB > 4.5V and VBL > 4.0V ( after built-in / extended blanking time )

Open Loop

-> Output Over Load

VCC Undervoltage / short Opto-coupler

VCC < 10.5V

Protection Mode Latched off Latched off Latched off Latched off Auto Restart Auto Restart Auto Restart

Application Note

14

2009-11-01

ICE3Axx65ELJ

6.6.1 Auto Restart Mode
There is always a startup phase with switching pulses in the Auto Restart Mode. After this startup phase the fault conditions are checked. If the fault persists, it would continue the auto-restart mode. Otherwise, it would resume to normal mode. Figure 12 shows the switching waveform of the VCC and the feedback voltage VFB when the output is shorted to ground. The IC turns on when the VCC reaches 18V. It then start the startup phase. However, the IC is off again due to the fault still persists. The VCC is discharged until 10.5V. Then, the Startup Cell is activated again to charge up capacitor at VCC to 18V. Then it initiates another restart cycle.
Vds
Vcc
Vfb

Vbl
Figure 12 Auto Restart Mode ( without extended blanking time )
6.6.2 Latched Off Mode
In case of Latched Off Mode, there is no new startup phase any more. Once Latched Off Mode is entered, the internal Voltage Reference is switched off in order to reduce the current consumption of the IC. In this stage only the UVLO circuit is working which switches on/off the startup cell at VCCon/VCCoff. Latched Off Mode can only be reset when AC line input is removed and the VCC is discharged to lower than 6.23V.
Vds
Vcc

Vfb

Vbl

Figure 13 Latch off Mode ( VBL < 0.1V )

Application Note

15

2009-11-01

ICE3Axx65ELJ

6.6.3 Blanking Time for over load protection

The IC controller provides a blanking window before entering into the auto restart mode due to output overload/short circuit. The purpose is to ensure that the system will not enter protection mode unintentionally. There are 2 kinds of the blanking time; basic and the extendable. The basic one is a built-in feature which is set at 20ms. The extendable one is to extend the basic one with a user defined additional blanking time. The extendable blanking time can be achieved by adding a capacitor, CBK to the BL pin. When there is over load occurred (VFB > 4.5V), the CBK capacitor will be charged up by an constant current source, IBK ( 8.4uA ) from 0.9V to 4.0V. Then the auto restart protection will be activated. The charging time from 0.9V to 4.0V to the CBK capacitor is the extended blanking time. The total blanking time can be calculated by the Equation(6).

Tblanking = Basic + Extended = 20ms + (4.0 - 0.9) * CBK = 20ms + 369047.6 * CBK

(6)

IBK

The measured total blanking time showing in figure 14 is 125ms using CBK=0.22uF.

In case of output overload or short circuit, the transferred power during the blanking period is limited to the maximum power defined by the value of the current sense resistor Rsense.

Vout

20ms Vfb

Vbl

Iout

Figure 14 Blanking window for over load protection ( basic blanking time )

Vout
Vfb 20ms
Vbl Iout

105ms

Figure 15 Blanking window for overload protection ( with extended blanking time, CBK=0.22uF )

Application Note

16

2009-11-01

ICE3Axx65ELJ

7

Layout Consideration

In order to get the optimized performance of the CoolSET®-F3, the grounding of the PCB layout must be connected carefully. From the circuit diagram in Figure 3, it indicates that the grounding for the CoolSET®-F3 can be split into several groups; signal ground, Vcc ground, Current sense resistor ground and EMI return ground. All the split grounds should be "star" connected to the bulk capacitor ground directly. The split grounds are described as below.
· Signal ground includes all small signal grounds connecting to the CoolSET® GND pin such as filter capacitor ground, C6, C7, C8 and opto-coupler ground.

· Vcc ground includes the Vcc capacitor ground, C5 and the auxiliary winding ground, pin 2 of the power transformer.

· Current Sense resistor ground includes current sense resistor R4 and R4A.

· EMI return ground includes Y capacitor, C4.

8

CoolSET®-F3 ICE3Axx65ELJ product list

Device

Package

VDS

Current /A Rdson /1

ICE3A1065ELJ PG-DIP-8 650V

1.0

2.95

ICE3A2065ELJ PG-DIP-8 650V

2.0

0.92

Frequency / KHz
100 100

Pout Vin=230Vac±15%2
32W 57W

Pout Vin=85-265Vac 2
16W 28W

9

Useful formula & external component design

Transformer calculation ( DCM flyback) Input data Turn ratio Maximum Duty ratio Primary Inductance Primary peak current

Vin_min = 90Vdc, Vin_max = 380Vdc, Vds_max = 470V for 600V MOSFET, Dmax  50%

N ratio

=

V - V ds _ max

in _ max

Vout + Vdiode

Dmax

=

(Vout + Vdiode )  Nratio Vin _ min + (Vout + Vdiode )  N ratio

Lp



(Vin _ min  Dmax )2 2  Pin  fsw

I p _ max

= Vin _ min  Dmax Lp  fsw

Primary turns

Np



I p _ max  Lp Bmax  Amin

1 Typ @ 25°C 2 Calculated maximum input power rating at Ta=75°C, Tj=125°C and without copper area as heat sink.

Application Note

17

2009-11-01

ICE3Axx65ELJ

Secondary turns Auxiliary turns

Ns

=

Np N ratio

N aux

=

Vcc + Vdiode Vout + Vdiode

 Ns

ICE3AXX65ELJ external component design

Current sense resistor Soft start time

R  VI sense

csth _ max p _ max

tsoft = 20ms

Vcc capacitor Startup time Enter burst mode power Leave burst mode power

CVCC

=

IVCC sup 2  tsoft VCCHY



2 3

t = V I  C STARTUP

VCCon Vcc CCch arg e3

Pburst _ enter

=

1 2



LP

 (VFB _ enter - VOffset-Ramp Rsense  AV

)2



f SW

Pburst _ max = 0.0961 Pin _ max

Output ripple during burst mode
Voltage drop when leave burst mode Total blanking time for over load protection

Vout _ ripple _ pp

=

RFB

Ropto  Gopto  GTL431

 VFB

Vout _ drop _ max

=

1.195  Ropto RFB  Gopto  GTL431

tblanking = 20ms + 369047.6  CBK

10

References

[1] Infineon Technologies, Datasheet "CoolSET®-F3 ICE3A1065ELJ Off-Line SMPS Current Mode Controller with Integrated 650V CoolMOS® and Startup Cell (Latched and Frequency Jitter Mode)"

[2] Kyaw Zin Min, Eric Kok Siu Kam, Infineon Technologies, Application Note "AN-EVALSF3ICE3A1065ELJ, 15W 5.0V SMPS Evaluation Board with CoolSET®-F3 ICE3A1065ELJ "

[3] Harald Zoellinger, Rainer Kling, Infineon Technologies, Application Note "AN-SMPS-ICE2xXXX-1, CoolSETTM ICE2xXXXX for Off-Line Switching Mode Power Supply (SMPS )"

Application Note

18

2009-11-01


Acrobat Distiller 5.0.5 (Windows)

Search Any Device: