Measurement Report

Kent

Test Report

Shenzhen Pard Technology Co.,Ltd OCELOT Thermal Imaging Camera 2A3OF-OCELOT 2A3OFOCELOT ocelot

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 85 Pages, 5.70MB

Document DEVICE REPORTGetApplicationAttachment.html?id=7376335
Project No.: ZHT-240425006E Page 1 of 85
FCC TEST REPORT FCC ID:2A3OF-OCELOT
Report Number...................................: ZHT-240425006E
Date of Test...........................................: Apr. 25, 2024 to June 05, 2024
Date of issue.........................................: June 05, 2024
Test Result............................................ : PASS
Testing Laboratory............................ : Guangdong Zhonghan Testing Technology Co., Ltd.
Address ............................................... : Room 104, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China
Applicant's name .............................: Shenzhen Pard Technology Co.,Ltd
Address ............................................... : B78,18/F,Guangyin building,38 Futian South Road, port community, Futian street, Futian District, Shenzhen
Manufacturer's name ......................: Shenzhen Pard Technology Co.,Ltd
Address ............................................... : B78,18/F,Guangyin building,38 Futian South Road, port community, Futian street, Futian District, Shenzhen
Test specification:
Standard................................................: FCC CFR Title 47 Part 15 Subpart C Section 15.247
Test procedure......................................: KDB558074 D01 15.247 Meas Guidance v05r02 ANSI C63.10:2013
Non-standard test method ................: N/A
This device described above has been tested by ZHT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZHT, this document may be altered or revised by ZHT, personal only, and shall be noted in the revision of the document. Product name..................................... : Thermal Imaging Camera
Trademark ...........................................: PARD
Model/Type reference......................... : Ocelot 640 S Ocelot 256 S, Ocelot 384 S, Ocelot 480 S, Ocelot 800 S, Ocelot 1024 S, Ocelot 1280 S, TH-MP11L, TH-MP11, TH-MH25L, TH-MH25, TH-MH35L, TH-MH35, TH-MQ35L, TH-SP19C, TH-SP19CL, TH-SH35CL, TH-SQ50CL, HA2, HA4, HA6, OS2, OS4, OS6, LE2, LE4, LE6, SP2, SP4, SP6, LA4C, LA6C, LA2QC, PR6, PR4, OC2, OC4, OC6, OC6Z, PA2, PA4, PA6, PA6Z, SA40, SA41, SA42, SA43, SA44, SA45, SA46
Model Difference ................................ : Ocelot 640 S is tested model, other models are derivative models .The models are identical in circuit, only different on the model names. So the test data of Ocelot 640 S can represent the remaining models.
Ratings.................................................. : Input: 5V 1A or DC 3.7V by Li-ion battery

Testing procedure and testing location:

Project No.: ZHT-240425006E Page 2 of 85

Testing Laboratory....................................... : Guangdong Zhonghan Testing Technology Co., Ltd.
Address............................................................ : Room 104, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China

Tested by (name + signature)....................... : Leon Li

Reviewer (name + signature)....................... : Baret Wu

Approved (name + signature)....................... : Levi Lee

Project No.: ZHT-240425006E Page 3 of 85
Table of Contents
Page
1. VERSION ..................................................................................................................................... 5
2. SUMMARY OF TEST RESULTS .................................................................................................6 2.1 TEST FACILITY ....................................................................................................................7 2.2 MEASUREMENT UNCERTAINTY .......................................................................................7
3. GENERAL INFORMATION ......................................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT .................................................................................... 8 3.2 DESCRIPTION OF TEST MODES ...................................................................................... 9 3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED .................9 3.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) ........................................ 10 3.5EQUIPMENTS LIST FOR ALL TEST ITEMS ..................................................................... 11
4. EMC EMISSION TEST .............................................................................................................. 13 4.1 CONDUCTED EMISSION MEASUREMENT .................................................................... 13 4.1.1 POWER LINE CONDUCTED EMISSION Limits ..................................................... 13 4.1.2 TEST PROCEDURE .................................................................................................. 13 4.1.3 DEVIATION FROM TEST STANDARD .....................................................................13 4.1.4 TEST SETUP ............................................................................................................. 14 4.1.5 EUT OPERATING CONDITIONS ..............................................................................14 4.2 RADIATED EMISSION MEASUREMENT ......................................................................... 17 4.2.1 RADIATED EMISSION LIMITS ................................................................................. 17 4.2.2 TEST PROCEDURE .................................................................................................. 17 4.2.3 DEVIATION FROM TEST STANDARD .....................................................................18 4.2.4 TEST SETUP ............................................................................................................. 18 4.2.5 EUT OPERATING CONDITIONS ..............................................................................19 4.2.6 TEST RESULTS .........................................................................................................19
5. RADIATED BAND EMISSIONMEASUREMENT ......................................................................24 5.1 TEST REQUIREMENT: ...................................................................................................... 24 5.2 TEST PROCEDURE .......................................................................................................... 24 5.3 DEVIATION FROM TEST STANDARD ............................................................................. 24 5.4 TEST SETUP ......................................................................................................................25 5.5 EUT OPERATING CONDITIONS ...................................................................................... 25 5.6 TEST RESULT ....................................................................................................................26
6. POWER SPECTRAL DENSITY TEST ...................................................................................... 28 6.1 APPLIED PROCEDURES / LIMIT ..................................................................................... 28 6.2 TEST PROCEDURE .......................................................................................................... 28 6.3 DEVIATION FROM STANDARD ....................................................................................... 28 6.4 TEST SETUP ......................................................................................................................28 6.5 EUT OPERATION CONDITIONS ...................................................................................... 28

Project No.: ZHT-240425006E Page 4 of 85
6.6 TEST RESULT ....................................................................................................................29
7. CHANNEL BANDWIDTH .......................................................................................................... 30 7.1 APPLIED PROCEDURES / LIMIT ..................................................................................... 30 7.2 TEST PROCEDURE .......................................................................................................... 30 7.3 DEVIATION FROM STANDARD ....................................................................................... 30 7.4 TEST SETUP ......................................................................................................................30 7.5 EUT OPERATION CONDITIONS ...................................................................................... 30 7.6 TEST RESULT ....................................................................................................................31
8. PEAK OUTPUT POWER TEST ................................................................................................ 32 8.1 APPLIED PROCEDURES/LIMIT ....................................................................................... 32 8.2 TEST PROCEDURE .......................................................................................................... 32 8.3 DEVIATION FROM STANDARD ....................................................................................... 32 8.4 TEST SETUP ......................................................................................................................32 8.5 EUT OPERATION CONDITIONS ...................................................................................... 32 8.6 TEST RESULT ....................................................................................................................32
9. CONDUCTED BAND EDGE AND SPURIOUS EMISSION ..................................................... 33 9.1 APPLICABLE STANDARD ................................................................................................33 9.2 TEST PROCEDURE .......................................................................................................... 33 9.3 DEVIATION FROM STANDARD ....................................................................................... 33 9.4 TEST SETUP ......................................................................................................................33 9.5 EUT OPERATION CONDITIONS ...................................................................................... 33 9.6 TEST RESULTS ................................................................................................................. 33
10. ANTENNA REQUIREMENT .................................................................................................... 34
11. APPENDIX WIFI .......................................................................................................................35 11.1 DUTY CYCLE ................................................................................................................... 35 11.2 -6DB BANDWIDTH .......................................................................................................... 42 11.3 OCCUPIED CHANNEL BANDWIDTH .............................................................................49 11.4 MAXIMUM POWER SPECTRAL DENSITY LEVEL ....................................................... 56 11.5 BAND EDGE .................................................................................................................... 63 11.6 CONDUCTED RF SPURIOUS EMISSION ...................................................................... 72
12. TEST SETUP PHOTO ............................................................................................................. 85
13. EUT CONSTRUCTIONAL DETAILS .......................................................................................85

1. VERSION Report No.
ZHT-240425006E

Version Rev.01

Project No.: ZHT-240425006E Page 5 of 85

Description Initial issue of report

Approved June 05, 2024

2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards:

Project No.: ZHT-240425006E Page 6 of 85

Standard Section FCC part 15.203/15.247 (b)(4) FCC part 15.207
FCC part 15.247 (b)(3)
FCC part 15.247 (a)(2)
FCC part 15.247 (e)
FCC part 15.247(d)
FCC part 15.205/15.209

FCC Part15 (15.247) , Subpart C Test Item
Antenna requirement AC Power Line Conducted Emission
Conducted Peak Output Power Channel Bandwidth
Power Spectral Density Band Edge
Spurious Emission

Result PASS PASS PASS PASS PASS PASS PASS

Remark

NOTE:
(1) " N/A" denotes test is not applicable in this Test Report

Project No.: ZHT-240425006E Page 7 of 85
2.1 TEST FACILITY Guangdong Zhonghan Testing Technology Co., Ltd. Add. : Room 104, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China
FCC Registration Number:255941 Designation Number: CN0325 IC Registered No.: 29832 CAB identifier: CN0143

2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± Uwhere expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2providing a level of confidence of approximately 95 %

No.

Item

Uncertainty

1

Conducted Emission Test

±1.38dB

2

RF conducted power

±0.16dB

3

Conducted spurious emissions

±0.21dB

4

All radiated emissions (9k-30MHz)

±4.68dB

5

All radiated emissions (<1G)

±4.68dB

6

All radiated emissions (>1G)

±4.89dB

7

Temperature

±0.5°C

8

Humidity

±2%

9

Occupied Bandwidth

±4.96%

Project No.: ZHT-240425006E Page 8 of 85

3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT

Product Name:

Thermal Imaging Camera

Test Model No.:

Ocelot 640 S

Hardware Version:

V1.0

Software Version:

V1.0

Sample(s) Status:

Engineer sample

Channel numbers: Operation Frequency: Channel separation: Modulation technology: Antenna Type:

802.11b/802.11g /802.11n(HT20):11/ 802.11n(HT40):7
802.11b/802.11g /802.11n(HT20): 2412-2462MHz 802.11n(HT40): 2422-2452MHz
5MHz
IEEE 802.11b: DQPSK/DBPSK/DSSS/CCK IEEE 802.11g: QPSK/BPSK/16QAM/64QAM/OFDM IEEE 802.11n: QPSK/BPSK/16QAM/64QAM/OFDM
FPC antenna

Antenna gain:

1.5dBi

Power supply:

Input: 5V

.............................................

1A or DC 3.7V by Li-ion battery

Project No.: ZHT-240425006E Page 9 of 85

Operation Frequency each of channel Channel Frequency Channel Frequency

Channel

Frequency

Channel Frequency

1

2412MHz

4

2427MHz

7

2442MHz

10

2457MHz

2

2417MHz

5

2432MHz

8

2447MHz

11

2462MHz

3

2422MHz

6

2437MHz

9

2452MHz

Note:
In section 15.31(m), regards to the operating frequency range over 10 MHz, the Lowest frequency, the middle frequency, and the highest frequency of channel were selected to perform the test, and the selected channel see below:

Test channel

Frequency (MHz)

802.11b/802.11g/802.11n(HT20)

802.11n(HT40)

Lowest channel

2412MHz

2422MHz

Middle channel

2437MHz

2437MHz

Highest channel

2462MHz

2452MHz

3.2 DESCRIPTION OF TEST MODES

Transmitting mode

Keep the EUT in continuously transmitting mode

Remark: EUT use new battery during the test, the test voltage was tuned from 85% to 115% of the nominal rated supply voltage, and found that the worst case was under the nominal rated supply condition. So the report just shows that condition's data.

We have verified the construction and function in typical operation. All the test modes were carried out with the EUT in transmitting operation, which was shown in this test report and defined as follows:

Pre-scan all kind of data rate in lowest channel, and found the follow list which it was worst case.

Mode

802.11b

802.11g

802.11n(HT20) 802.11n(HT40)

Data rate

1Mbps

6Mbps

6.5Mbps

13Mbps

3.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED Radiated Emission EUT
Conducted Spurious Adapter EUT

3.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE)

Project No.: ZHT-240425006E Page 10 of 85

The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests.

Item Equipment

E-1

Adapter

Mfr/Brand N/A

Model/Type No. HW-059200CHQ

Series No. N/A

Note AE

Item Shielded Type Ferrite Core

Length

Note

Note:
(1) (2)

The support equipment was authorized by Declaration of Confirmation. For detachable type I/O cable should be specified the length in cm inLengthcolumn.

3.5EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment

Project No.: ZHT-240425006E Page 11 of 85

Item Equipment

Manufacturer

Model

1

Receiver

R&S

ESCI

2

Loop antenna

EMCI

LAP600

3

Amplifier

Schwarzbeck BBV 9743 B

4

Amplifier

Schwarzbeck BBV 9718 B

5

Bilog Antenna Schwarzbeck

VULB9162

6

Horn Antenna Schwarzbeck BBHA9120D

7

Horn Antenna A.H.SYSTEMS

SAS574

8

Amplifier

AEROFLEX 100KHz-40GHz

9

Spectrum Analyzer

R&S

10

966 Anechoic Chamber

EMToni

11

Spectrum Analyzer

KEYSIGHT

WIDBAND

12

RADIO COMMUNICATI

R&S

ON TESTER

13

Single Generator

Agilent

FSV40 9m6m6m N9020A
CMW500
N5182A

14 Power Sensor

MWRFtest

MW100-RFCB

15 Audio analyzer

16

Single Generator

17

Power Amplifier Shielding Room

R&S R&S EMToni

UPL SMB100A 2m3m3m

Last Cal. May 12, 2023 May 12, 2023 May 12, 2023 May 12, 2023 May 17, 2023 May 17, 2023 May 12, 2023 May 12, 2023 May 12, 2023 Nov. 25, 2021 May 12, 2023
May 12, 2023
May 12, 2023 May 12, 2023 May 12, 2023 May 12, 2023 Nov. 25, 2021

Next Cal. May 11, 2024 May 11, 2024 May 11, 2024 May 11, 2024 May 16, 2024 May 16, 2024 May 11, 2024 May 11, 2024 May 11, 2024 Nov. 24, 2024 May 11, 2024
May 11, 2024
May 11, 2024 May 11, 2024 May 11, 2024 May 11, 2024 Nov. 24, 2024

Conduction Test equipment

Equipment
Receiver
LISN
ISN CAT 6
ISN CAT 5 Capacitive Voltage
Probe Current Transformer Clamp CE Shielding Room

Manufacturer R&S R&S
Schwarzbeck Schwarzbeck Schwarzbeck Schwarzbeck
EMToni

Model ESCI ENV216 NTFM 8158 CAT5 8158 CVP 9222 C SW 9605 9m4m3m

Project No.: ZHT-240425006E Page 12 of 85

Last Cal. May 12, 2023 May 12, 2023 May 12, 2023 May 12, 2023 May 12, 2023 May 12, 2023 Nov. 25, 2021

Next Cal. May 11, 2024 May 11, 2024 May 11, 2024 May 11, 2024 May 11, 2024 May 11, 2024 Nov. 24, 2024

Project No.: ZHT-240425006E Page 13 of 85

4. EMC EMISSION TEST 4.1 CONDUCTED EMISSION MEASUREMENT

Test Requirement:

FCC Part15 C Section 15.207

Test Method:

ANSI C63.10:2013

Test Frequency Range: 150KHz to 30MHz

Receiver setup:

RBW=9KHz, VBW=30KHz, Sweep time=auto

4.1.1 POWER LINE CONDUCTED EMISSION Limits

FREQUENCY (MHz)

Limit (dBuV)

Quasi-peak

Average

Standard

0.15 -0.5

66 - 56 *

56 - 46 *

FCC

0.50 -5.0

56.00

46.00

FCC

5.0 -30.0

60.00

50.00

Note:

(1) *Decreases with the logarithm of the frequency.

FCC

4.1.2 TEST PROCEDURE
a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument.
b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long.
c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m.
d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item ­EUT Test Photos.

4.1.3 DEVIATION FROM TEST STANDARD No deviation

4.1.4 TEST SETUP

Project No.: ZHT-240425006E Page 14 of 85

4.1.5 EUT OPERATING CONDITIONS
The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

4.1.6 TEST RESULT

Temperature: Pressure: Test Voltage:

24.3 101kPa AC 120V/60Hz

Project No.: ZHT-240425006E Page 15 of 85

Relative Humidity : Phase :

50% L

Notes: 1.An initial pre-scan was performed on the line and neutral lines with peak detector. 2.Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3.Mesurement Level = Reading level + Correct Factor 4.The test data shows only the worst case 802.11b mode ( Low Channel:2412MHz ).

Temperature: Pressure: Test Voltage:

24.3 101kPa AC 120V/60Hz

Project No.: ZHT-240425006E Page 16 of 85

Relative Humidity : Phase :

50% N

Notes: 1.An initial pre-scan was performed on the line and neutral lines with peak detector. 2.Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3.Mesurement Level = Reading level + Correct Factor 4.The test data shows only the worst case 802.11b mode ( Low Channel:2412MHz).

4.2 RADIATED EMISSION MEASUREMENT

Project No.: ZHT-240425006E Page 17 of 85

Test Requirement: Test Method: Test Frequency Range: Test site: Receiver setup:

FCC Part15 C Section 15.209

ANSI C63.10:2013

9kHz to 25GHz

Measurement Distance: 3m

Frequency

Detector

RBW VBW

Value

9KHz-150KHz Quasi-peak 200Hz 600Hz Quasi-peak

150KHz-30MHz Quasi-peak 9KHz 30KHz Quasi-peak

30MHz-1GHz Quasi-peak 100KHz 300KHz Quasi-peak

Above 1GHz

Peak Peak

1MHz 1MHz

3MHz 10Hz

Peak Average

4.2.1 RADIATED EMISSION LIMITS

Frequencies

Field Strength

(MHz)

(micorvolts/meter)

0.009~0.490

2400/F(KHz)

0.490~1.705

24000/F(KHz)

1.705~30.0

30

30~88

100

88~216

150

216~960

200

Above 960

500

LIMITS OF RADIATED EMISSION MEASUREMENT

Measurement Distance (meters) 300 30 30 3 3 3 3

FREQUENCY (MHz)

Limit (dBuV/m) (at 3M)

PEAK

AVERAGE

Above 1000

74

54

Notes:

(1) The limit for radiated test was performed according to FCC PART 15C.

(2) The tighter limit applies at the band edges.

(3) Emission level (dBuV/m)=20log Emission level (uV/m).

4.2.2 TEST PROCEDURE Below 1GHz test procedure as below:
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoiccamber. The table was rotated 360 degrees to determine the position of the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of avariable-height antenna tower.

Project No.: ZHT-240425006E Page 18 of 85
c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading.
e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode.
f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dBmargin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet.
Above 1GHz test procedure as below:
g. Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber and change form table 0.8 meter to 1.5 meter( Above 18GHz the distance is 1 meter and table is 1.5 meter).
h. Test the EUT in the lowest channel ,the middle channel ,the Highest channel
Note:
Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported
4.2.3 DEVIATION FROM TEST STANDARD No deviation
4.2.4 TEST SETUP
ARadiated Emission Test-Up Frequency Below 30MHz

BRadiated Emission Test-Up Frequency 30MHz~1GHz

Project No.: ZHT-240425006E Page 19 of 85

CRadiated Emission Test-Up Frequency Above 1GHz
4.2.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. 4.2.6 TEST RESULTS
Between 9KHz ­ 30MHz The emission from 9 kHz to 30MHz was pre-tested and found the result was 20dB lower than the limit, and according to 15.31(o) & RSS-Gen 6.13, the test result no need to reported.

Between 30MHz ­ 1GHz

Temperature Pressure Test Voltage 

25.1 101kPa DC 3.7V

Project No.: ZHT-240425006E Page 20 of 85

Relative Humidity : Polarization :

50% Horizontal

Temperature Pressure Test Voltage 

25.1 101kPa DC 3.7V

Project No.: ZHT-240425006E Page 21 of 85

Relative Humidity : Polarization :

50% Vertical

Remarks: 1.Final Level =Receiver Read level + Antenna Factor + Cable Loss ­ Preamplifier Factor 2.The emission levels of other frequencies are very lower than the limit and not show in test report. 3.The test data shows only the worst case 802.11b mode ( Low Channel:2412MHz).

Project No.: ZHT-240425006E Page 22 of 85

1GHz~25GHz
Polar Frequency (H/V) (MHz)

V

4824.00

V

4824.00

H

4824.00

H

4824.00

V

4874.00

V

4874.00

H

4874.00

H

4874.00

V

4924.00

V

4924.00

H

4924.00

H

4924.00

V

4824.00

V

4824.00

H

4824.00

H

4824.00

V

4874.00

V

4874.00

H

4874.00

H

4874.00

V

4924.00

V

4924.00

H

4924.00

H

4924.00

V

4824.00

V

4824.00

H

4824.00

H

4824.00

V

4874.00

V

4874.00

H

4874.00

4874.00

V

4924.00

V

4924.00

H

4924.00

H

4924.00

V

4844.00

V

4844.00

Meter Reading (dBuV)
59.29 42.36 57.41 44.69
55.98 44.27 57.23 44.68
57.68 41.63 59.91 42.24
59.08 41.46 56.76 41.1
56.82 41.46 59.66 44.95
56.62 43.09 58.57 41.08
55.39 42.66 58.16 43.42
57.19 41.66 58.93 42.92
57.9 41.53 58.72 42.59
59.8 41.18

Pre-ampl Cable Antenna Emission

ifier

Loss Factor

Level

(dB)

(dB)

(dB) (dBuV/m)

802.11b

Low Channel:2412MHz

30.55 5.77 24.66

59.17

30.55 5.77 24.66

42.24

30.33 6.32 24.55

57.95

30.33 6.32 24.55

45.23

Middle Channel:2437MHz

30.55 5.77 24.66

55.86

30.55 5.77 24.66

44.15

30.33 6.32 24.55

57.77

30.33 6.32 24.55

45.22

High Channel:2462MHz

30.55

5.77

24.66

57.56

30.55

5.77

24.66

41.51

30.33

6.32

24.55

60.45

30.33

6.32

24.55

42.78

802.11g

Low Channel:2412MHz

30.55 5.77 24.66

58.96

30.55 5.77 24.66

41.34

30.33 6.32 24.55

57.3

30.33 6.32 24.55

41.64

Middle Channel:2437MHz

30.55 5.77 24.66

56.7

30.55 5.77 24.66

41.34

30.33 6.32 24.55

60.2

30.33 6.32 24.55

45.49

High Channel:2462MHz

30.55

5.77

24.66

56.5

30.55

5.77

24.66

42.97

30.33

6.32

24.55

59.11

30.33

6.32

24.55

41.62

802.11n 20

Low Channel:2412MHz

30.55 5.77 24.66

55.27

30.55 5.77 24.66

42.54

30.33 6.32 24.55

58.7

30.33 6.32 24.55

43.96

Middle Channel:2437MHz

30.55 5.77 24.66

57.07

30.55 5.77 24.66

41.54

30.33 6.32 24.55

59.47

30.33 6.32 24.55

43.46

High Channel:2462MHz

30.55

5.77

24.66

57.78

30.55

5.77

24.66

41.41

30.33

6.32

24.55

59.26

30.33

6.32

24.55

43.13

802.11n 40

Low Channel:2422MHz

30.55 5.77 24.66

59.68

30.55 5.77 24.66

41.06

Limits (dBuV/
m)
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54 74 54
74 54

Margin (dB)

Detect or
Type

-14.83

Pk

-11.76

AV

-16.05

Pk

-8.77

AV

-18.14

Pk

-9.85

AV

-16.23

Pk

-8.78

AV

-16.44

Pk

-12.49

AV

-13.55

Pk

-11.22

AV

-15.04

Pk

-12.66

AV

-16.7

Pk

-12.36

AV

-17.3

Pk

-12.66

AV

-13.8

Pk

-8.51

AV

-17.5

Pk

-11.03

AV

-14.89

Pk

-12.38

AV

-18.73

Pk

-11.46

AV

-15.3

Pk

-10.04

AV

-16.93

Pk

-12.46

AV

-14.53

Pk

-10.54

AV

-16.22

Pk

-12.59

AV

-14.74

Pk

-10.87

AV

-14.32

Pk

-12.94

AV

Project No.: ZHT-240425006E

Page 23 of 85

H

4844.00 55.91

30.33

6.32 24.55

56.45

74

-17.55

Pk

H

4844.00 41.87

30.33

6.32 24.55

42.41

54

-11.59

AV

Middle Channel:2437MHz

V

4874.00 58.91

30.55

5.77 24.66

58.79

74

-15.21

Pk

V

4874.00 41.42

30.55

5.77 24.66

41.3

54

-12.7

AV

H

4874.00 56.16

30.33

6.32 24.55

56.7

74

-17.3

Pk

H

4874.00 41.15

30.33

6.32 24.55

41.69

54

-12.31

AV

High Channel:2452MHz

V

4904.00

55.9

30.55

5.77

24.66

55.78

74

-18.22

Pk

V

4904.00

43.1

30.55

5.77

24.66

42.98

54

-11.02

AV

H

4904.00

59.6

30.33

6.32

24.55

60.14

74

-13.86

Pk

H

4904.00 44.72

30.33

6.32 24.55

45.26

54

-8.74

AV

Remark: 1. Emission Level = Meter Reading + Antenna Factor + Cable Loss ­ Pre-amplifier, Margin= Emission Level - Limit 2. If peak below the average limit, the average emission was no test. 3. The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. 4.For above 1GHz, the test result of peak was 20dB below to the limit of peak, which can be compliant to the
average limit, so just peak value was recorded.

Project No.: ZHT-240425006E Page 24 of 85

5. RADIATED BAND EMISSIONMEASUREMENT

5.1 TEST REQUIREMENT: Test Requirement: Test Method:

FCC Part15 C Section 15.209 and 15.205 ANSI C63.10: 2013

Test Frequency Range: Test site:

All of the restrict bands were tested, only the worst band's (2310MHz to 2500MHz) data was showed. Measurement Distance: 3m

Receiver setup:

Frequency Above 1GHz

Detector Peak
Average

RBW 1MHz 1MHz

VBW 3MHz 3MHz

Value Peak Average

LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz)

FREQUENCY (MHz)

Class B (dBuV/m) (at 3M)

PEAK

AVERAGE

Above 1000

74

54

Notes:

(1) The limit for radiated test was performed according to FCC PART 15C.

(2) The tighter limit applies at the band edges.

(3) Emission level (dBuV/m)=20log Emission level (uV/m).

5.2 TEST PROCEDURE Above 1GHz test procedure as below:
a. 1. The EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower.
c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading.
e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode.
f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dBmargin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet.
g. Test the EUT in the lowest channel,the Highest channel
Note:
Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported

5.3 DEVIATION FROM TEST STANDARD No deviation

5.4 TEST SETUP Radiated Emission Test-Up Frequency Above 1GHz

Project No.: ZHT-240425006E Page 25 of 85

5.5 EUT OPERATING CONDITIONS
The EUT tested system was configured as the statements of 2.3 Unless otherwise a special operating condition is specified in the follows during the testing.

Project No.: ZHT-240425006E Page 26 of 85

5.6 TEST RESULT

802.11b
802.11g
802.11n2 0

Polar (H/V)
H H H H V V V V
H H H H V V V V
H H H H V V V V
H H H H V V V V
H H H H V V V V
H H H H V

Frequency (MHz)
2390.00 2390.00 2400.00 2400.00 2390.00 2390.00 2400.00 2400.00
2483.50 2483.50 2500.00 2500.00 2483.50 2483.50 2500.00 2500.00
2390.00 2390.00 2400.00 2400.00 2390.00 2390.00 2400.00 2400.00
2483.50 2483.50 2500.00 2500.00 2483.50 2483.50 2500.00 2500.00
2390.00 2390.00 2400.00 2400.00 2390.00 2390.00 2400.00 2400.00
2483.50 2483.50 2500.00 2500.00 2483.50

Meter Reading (dBuV)
59.89 46.68 60.47 48.06 62.22 47.32 60.05 47.82
59.22 48.80 59.00 48.32 60.45 46.10 62.61 46.61
60.59 47.30 59.89 46.31 60.57 47.01 61.94 46.22
61.82 47.60 61.38 46.55 60.38 46.64 59.16 48.84
61.17 47.71 60.09 47.24 62.80 46.87 62.19 46.58
60.49 48.14 61.51 48.75 62.32

Preamplifi
er (dB)

Cable Antenna Loss Factor (dB) (dB/m)

Emission level
(dBuV/m)

LowChannel 2412MHz

30.22 4.85 23.98

58.50

30.22 4.85 23.98

45.29

30.22 4.85 23.98

59.08

30.22 4.85 23.98

46.67

30.22 4.85 23.98

60.83

30.22 4.85 23.98

45.93

30.22 4.85 23.98

58.66

30.22 4.85 23.98

46.43

High Channel 2462MHz

30.22 4.85 23.98

57.83

30.22 4.85 23.98

47.41

30.22 4.85 23.98

57.61

30.22 4.85 23.98

46.93

30.22 4.85 23.98

59.06

30.22 4.85 23.98

44.71

30.22 4.85 23.98

61.22

30.22 4.85 23.98

45.22

Low Channel 2412MHz

30.22 4.85 23.98

59.20

30.22 4.85 23.98

45.91

30.22 4.85 23.98

58.50

30.22 4.85 23.98

44.92

30.22 4.85 23.98

59.18

30.22 4.85 23.98

45.62

30.22 4.85 23.98

60.55

30.22 4.85 23.98

44.83

High Channel 2462MHz

30.22 4.85 23.98

60.43

30.22 4.85 23.98

46.21

30.22 4.85 23.98

59.99

30.22 4.85 23.98

45.16

30.22 4.85 23.98

58.99

30.22 4.85 23.98

45.25

30.22 4.85 23.98

57.77

30.22 4.85 23.98

47.45

Low Channel 2412MHz

30.22 4.85 23.98

59.78

30.22 4.85 23.98

46.32

30.22 4.85 23.98

58.70

30.22 4.85 23.98

45.85

30.22 4.85 23.98

61.41

30.22 4.85 23.98

45.48

30.22 4.85 23.98

60.80

30.22 4.85 23.98

45.19

High Channel 2462MHz

30.22 4.85 23.98

59.10

30.22 4.85 23.98

46.75

30.22 4.85 23.98

60.12

30.22 4.85 23.98

47.36

30.22 4.85 23.98

60.93

Limit Margi (dBuV n
/m) (dB)

74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-15.50 -8.71 -14.92 -7.33 -13.17 -8.07 -15.34 -7.57

74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-16.17 -6.59 -16.39 -7.07 -14.94 -9.29 -12.78 -8.78

74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-14.80 -8.09 -15.50 -9.08 -14.82 -8.38 -13.45 -9.17

74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-13.57 -7.79 -14.01 -8.84 -15.01 -8.75 -16.23 -6.55

74.00 54.00 74.00 54.00 74.00 54.00 74.00 54.00

-14.22 -7.68 -15.30 -8.15 -12.59 -8.52 -13.20 -8.81

74.00 54.00 74.00 54.00 74.00

-14.90 -7.25 -13.88 -6.64 -13.07

Detec tor
Type
PK AV PK AV PK AV PK AV
AV PK AV PK AV PK AV AV
PK AV PK AV PK AV PK AV
PK AV PK AV PK AV PK AV
PK AV PK AV PK AV PK AV
PK AV PK AV PK

Result
PASS PASS PASS PASS PASS PASS PASS PASS
PASS PASS PASS PASS PASS PASS PASS PASS
PASS PASS PASS PASS PASS PASS PASS PASS
PASS PASS PASS PASS PASS PASS PASS PASS
PASS PASS PASS PASS PASS PASS PASS PASS
PASS PASS PASS PASS PASS

Project No.: ZHT-240425006E

Page 27 of 85

V

2483.50 46.31 30.22 4.85 23.98

44.92 54.00 -9.08 AV PASS

V

2500.00 62.16 30.22 4.85 23.98

60.77 74.00 -13.23 PK PASS

V

2500.00 47.58 30.22 4.85 23.98

46.19 54.00 -7.81 AV PASS

Low Channel 2422MHz

H

2390.00 59.97 30.22 4.85 23.98

58.58 74.00 -15.42 PK PASS

H

2390.00 48.57 30.22 4.85 23.98

47.18 54.00 -6.82 AV PASS

H

2400.00 60.32 30.22 4.85 23.98

58.93 74.00 -15.07 PK PASS

H

2400.00 47.55 30.22 4.85 23.98

46.16 54.00 -7.84 AV PASS

V

2390.00 60.09 30.22 4.85 23.98

58.70 74.00 -15.30 PK PASS

V

2390.00 46.21 30.22 4.85 23.98

44.82 54.00 -9.18 AV PASS

V

2400.00 61.20 30.22 4.85 23.98

59.81 74.00 -14.19 PK PASS

802.11n

V

2400.00 46.77 30.22 4.85 23.98

45.38 54.00 -8.62 AV PASS

40

High Channel 2452MHz

H

2483.50 59.66 30.22 4.85 23.98

58.27 74.00 -15.73 PK PASS

H

2483.50 46.64 30.22 4.85 23.98

45.25 54.00 -8.75 AV PASS

H

2500.00 60.19 30.22 4.85 23.98

58.80 74.00 -15.20 PK PASS

H

2500.00 48.37 30.22 4.85 23.98

46.98 54.00 -7.02 AV PASS

V

2483.50 61.47 30.22 4.85 23.98

60.08 74.00 -13.92 PK PASS

V

2483.50 46.65 30.22 4.85 23.98

45.26 54.00 -8.74 AV PASS

V

2500.00 62.26 30.22 4.85 23.98

60.87 74.00 -13.13 PK PASS

V

2500.00 46.09 30.22 4.85 23.98

44.70 54.00 -9.30 AV PASS

Remark:

1. Emission Level = Meter Reading + Antenna Factor + Cable Loss ­ Pre-amplifier, Margin= Emission Level - Limit

Project No.: ZHT-240425006E Page 28 of 85

6. POWER SPECTRAL DENSITY TEST

Test Requirement: Test Method:

FCC Part15 C Section 15.247 (e) KDB558074 D0115.247 Meas Guidancev05r02

6.1 APPLIED PROCEDURES / LIMIT

Section 15.247

FCC Part15 (15.247) , Subpart C

Test Item

Limit

Power Spectral Density

8dBm/3kHz

Frequency Range (MHz)
2400-2483.5

Result PASS

6.2 TEST PROCEDURE
1. Set analyzer center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS bandwidth. 3. Set the RBW to: 3 kHz  RBW  100 kHz. 4. Set the VBW  3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level within the RBW. 10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat.
6.3 DEVIATION FROM STANDARD
No deviation.
6.4 TEST SETUP

6.5 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 2.1 Unless otherwise a special operating condition is specified in the follows during the testing.

6.6 TEST RESULT

Temperature Pressure

25.9 101kPa

Please refer to APPENDIX WIFI

Project No.: ZHT-240425006E Page 29 of 85

Relative Humidity 52%

Test Voltage 

DC 3.7V

7. CHANNEL BANDWIDTH

Project No.: ZHT-240425006E Page 30 of 85

Test Requirement: Test Method:

FCC Part15 C Section 15.247 (a)(2) KDB558074 D0115.247 Meas Guidancev05r02

7.1 APPLIED PROCEDURES / LIMIT

Section 15.247(a)(2)

FCC Part15 (15.247) , Subpart C

Test Item

Limit

Frequency Range (MHz)

Bandwidth

>= 500KHz (6dB bandwidth)

2400-2483.5

Result PASS

7.2 TEST PROCEDURE
1. Set RBW = 100 kHz. 2. Set the video bandwidth (VBW)  3 xRBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission.

7.3 DEVIATION FROM STANDARD No deviation. 7.4 TEST SETUP

7.5 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.

7.6 TEST RESULT

Temperature Pressure Test Mode 

25.8 101kPa TX Mode

Please refer to APPENDIX WIFI

Project No.: ZHT-240425006E Page 31 of 85

Relative Humidity 52%

Test Voltage 

DC 3.7V

Project No.: ZHT-240425006E Page 32 of 85

8. PEAK OUTPUT POWER TEST

Test Requirement: Test Method:

FCC Part15 C Section 15.247 (b)(3) KDB558074 D0115.247 Meas Guidancev05r02

8.1 APPLIED PROCEDURES/LIMIT

Section 15.247(b)(3)

FCC Part15 (15.247) , Subpart C

Test Item
Peak Output Power

Limit 1 watt or 30dBm

Frequency Range (MHz)
2400-2483.5

8.2 TEST PROCEDURE

a. The EUT was directly connected to the Power meter

8.3 DEVIATION FROM STANDARD

No deviation. 8.4 TEST SETUP

Result PASS

8.5 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing.
8.6 TEST RESULT

Temperature Pressure

25.3 101kPa

Relative Humidity 55%

Test Voltage 

DC 3.7V

Test CH
Lowest Middle Highest

Peak Output Power (dBm)

802.11b 802.11g 802.11n(HT20)

8.46

7.95

7.79

8.35

8.33

8.18

8.40

8.11

7.86

802.11n(HT40) 8.30 8.44 8.33

Limit(dBm) 30.00

Result Pass

9. CONDUCTED BAND EDGE AND SPURIOUS EMISSION

Project No.: ZHT-240425006E Page 33 of 85

Test Requirement: Test Method:

FCC Part15 C Section 15.247 (d) KDB558074 D0115.247 Meas Guidancev05r02

9.1 APPLICABLE STANDARD
in any 100 kHz bandwidth outside the frequency bands in which the spread spectrum intentional radiator in operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power, In addition, radiated emissions which fall in the restricted bands, as defined in§15.205(a), must also comply with the radiated emission limits specified in15.209(a).

9.2 TEST PROCEDURE
Using the following spectrum analyzer setting:
A) Set the RBW = 100KHz. B) Set the VBW = 300KHz. C) Sweep time = auto couple. D) Detector function = peak. E) Trace mode = max hold. F) Allow trace to fully stabilize.

9.3 DEVIATION FROM STANDARD No deviation. 9.4 TEST SETUP

9.5 EUT OPERATION CONDITIONS
The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. 9.6 TEST RESULTS
Please refer to APPENDIX WIFI

10. ANTENNA REQUIREMENT

Project No.: ZHT-240425006E Page 34 of 85

Standard requirement:

FCC Part15 C Section 15.203 /247(b)(4)

15.203 requirement:
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited.
15.247(b) (4) requirement:
(4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi.

EUT Antenna: The antenna is FPC antenna, the best case gain of the antenna is 1.5dBi, reference to the appendix II for details

11. APPENDIX WIFI

11.1 DUTY CYCLE

Mode

Frequency (MHz)

b

2412

b

2437

b

2462

g

2412

g

2437

g

2462

n20

2412

n20

2437

n20

2462

n40

2422

n40

2437

n40

2452

Duty Cycle (%) 98.73 98.65 99.28 93.24 94.09 95.39 97.46 96 97.47 85.59 85.45 93.07

Project No.: ZHT-240425006E Page 35 of 85

Correction Factor (dB) 0 0 0 0.3
0.26 0.2 0.11 0.18 0.11 0.68 0.68 0.31

1/T (kHz) 0.08 0.08 0.08 0.48 0.48 0.48 0.52 0.52 0.52 1.05 1.06 1.06

Test Graphs Duty Cycle NVNT b 2412MHz Ant1

Project No.: ZHT-240425006E Page 36 of 85

Duty Cycle NVNT b 2437MHz Ant1

Duty Cycle NVNT b 2462MHz Ant1

Project No.: ZHT-240425006E Page 37 of 85

Duty Cycle NVNT g 2412MHz Ant1

Duty Cycle NVNT g 2437MHz Ant1

Project No.: ZHT-240425006E Page 38 of 85

Duty Cycle NVNT g 2462MHz Ant1

Duty Cycle NVNT n20 2412MHz Ant1

Project No.: ZHT-240425006E Page 39 of 85

Duty Cycle NVNT n20 2437MHz Ant1

Duty Cycle NVNT n20 2462MHz Ant1

Project No.: ZHT-240425006E Page 40 of 85

Duty Cycle NVNT n40 2422MHz Ant1

Duty Cycle NVNT n40 2437MHz Ant1

Project No.: ZHT-240425006E Page 41 of 85

Duty Cycle NVNT n40 2452MHz Ant1

11.2 -6DB BANDWIDTH

Mode Frequency (MHz)

b

2412

b

2437

b

2462

g

2412

g

2437

g

2462

n20

2412

n20

2437

n20

2462

n40

2422

n40

2437

n40

2452

-6 dB Bandwidth (MHz) 10.059 9.997 10.068 16.323 16.349 16.322 17.543 17.025 17.261 35.407 35.334 35.449

Project No.: ZHT-240425006E Page 42 of 85

Limit -6 dB Bandwidth (MHz) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

Verdict Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass

Test Graphs -6dB Bandwidth NVNT b 2412MHz Ant1

Project No.: ZHT-240425006E Page 43 of 85

-6dB Bandwidth NVNT b 2437MHz Ant1

-6dB Bandwidth NVNT b 2462MHz Ant1

Project No.: ZHT-240425006E Page 44 of 85

-6dB Bandwidth NVNT g 2412MHz Ant1

-6dB Bandwidth NVNT g 2437MHz Ant1

Project No.: ZHT-240425006E Page 45 of 85

-6dB Bandwidth NVNT g 2462MHz Ant1

Project No.: ZHT-240425006E Page 46 of 85
-6dB Bandwidth NVNT n20 2412MHz Ant1
-6dB Bandwidth NVNT n20 2437MHz Ant1

Project No.: ZHT-240425006E Page 47 of 85
-6dB Bandwidth NVNT n20 2462MHz Ant1
-6dB Bandwidth NVNT n40 2422MHz Ant1

Project No.: ZHT-240425006E Page 48 of 85
-6dB Bandwidth NVNT n40 2437MHz Ant1
-6dB Bandwidth NVNT n40 2452MHz Ant1

11.3 OCCUPIED CHANNEL BANDWIDTH

Mode

Frequency (MHz)

b

2412

b

2437

b

2462

g

2412

g

2437

g

2462

n20

2412

n20

2437

n20

2462

n40

2422

n40

2437

n40

2452

Project No.: ZHT-240425006E Page 49 of 85
99% OBW (MHz) 15.021 14.956 14.941 16.53 16.569 16.504 17.625 17.658 17.607 36.125 36.126 36.181

Test Graphs OBW NVNT b 2412MHz Ant1

Project No.: ZHT-240425006E Page 50 of 85

OBW NVNT b 2437MHz Ant1

OBW NVNT b 2462MHz Ant1

Project No.: ZHT-240425006E Page 51 of 85

OBW NVNT g 2412MHz Ant1

OBW NVNT g 2437MHz Ant1

Project No.: ZHT-240425006E Page 52 of 85

OBW NVNT g 2462MHz Ant1

OBW NVNT n20 2412MHz Ant1

Project No.: ZHT-240425006E Page 53 of 85

OBW NVNT n20 2437MHz Ant1

OBW NVNT n20 2462MHz Ant1

Project No.: ZHT-240425006E Page 54 of 85

OBW NVNT n40 2422MHz Ant1

OBW NVNT n40 2437MHz Ant1

Project No.: ZHT-240425006E Page 55 of 85

OBW NVNT n40 2452MHz Ant1

11.4 MAXIMUM POWER SPECTRAL DENSITY LEVEL

Mode

Frequency (MHz)

Conducted PSD

(dBm/3kHz)

b

2412

-11.49

b

2437

-9.43

b

2462

-11.58

g

2412

-16.6

g

2437

-17.16

g

2462

-17.2

n20

2412

-16.28

n20

2437

-16.43

n20

2462

-16.58

n40

2422

-19.83

n40

2437

-19.32

n40

2452

-20.25

Project No.: ZHT-240425006E Page 56 of 85

Limit (dBm/3kHz)

Verdict

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

8

Pass

Test Graphs PSD NVNT b 2412MHz Ant1

Project No.: ZHT-240425006E Page 57 of 85

PSD NVNT b 2437MHz Ant1

PSD NVNT b 2462MHz Ant1

Project No.: ZHT-240425006E Page 58 of 85

PSD NVNT g 2412MHz Ant1

PSD NVNT g 2437MHz Ant1

Project No.: ZHT-240425006E Page 59 of 85

PSD NVNT g 2462MHz Ant1

PSD NVNT n20 2412MHz Ant1

Project No.: ZHT-240425006E Page 60 of 85

PSD NVNT n20 2437MHz Ant1

PSD NVNT n20 2462MHz Ant1

Project No.: ZHT-240425006E Page 61 of 85

PSD NVNT n40 2422MHz Ant1

PSD NVNT n40 2437MHz Ant1

Project No.: ZHT-240425006E Page 62 of 85

PSD NVNT n40 2452MHz Ant1

11.5 BAND EDGE

Mode

Frequency (MHz)

b

2412

b

2462

g

2412

g

2462

n20

2412

n20

2462

n40

2422

n40

2452

Max Value (dBc) -46.02 -54.87 -39.5 -49.04 -38.36 -50.43 -35.96 -45.26

Project No.: ZHT-240425006E Page 63 of 85

Limit (dBc) -20 -20 -20 -20 -20 -20 -20 -20

Verdict Pass Pass Pass Pass Pass Pass Pass Pass

Test Graphs Band Edge NVNT b 2412MHz Ant1 Ref

Project No.: ZHT-240425006E Page 64 of 85

Band Edge NVNT b 2412MHz Ant1 Emission

Band Edge NVNT b 2462MHz Ant1 Ref

Project No.: ZHT-240425006E Page 65 of 85

Band Edge NVNT b 2462MHz Ant1 Emission

Band Edge NVNT g 2412MHz Ant1 Ref

Project No.: ZHT-240425006E Page 66 of 85

Band Edge NVNT g 2412MHz Ant1 Emission

Band Edge NVNT g 2462MHz Ant1 Ref

Project No.: ZHT-240425006E Page 67 of 85

Band Edge NVNT g 2462MHz Ant1 Emission

Band Edge NVNT n20 2412MHz Ant1 Ref

Project No.: ZHT-240425006E Page 68 of 85

Band Edge NVNT n20 2412MHz Ant1 Emission

Band Edge NVNT n20 2462MHz Ant1 Ref

Project No.: ZHT-240425006E Page 69 of 85

Band Edge NVNT n20 2462MHz Ant1 Emission

Band Edge NVNT n40 2422MHz Ant1 Ref

Project No.: ZHT-240425006E Page 70 of 85

Band Edge NVNT n40 2422MHz Ant1 Emission

Band Edge NVNT n40 2452MHz Ant1 Ref

Project No.: ZHT-240425006E Page 71 of 85

Band Edge NVNT n40 2452MHz Ant1 Emission

11.6 CONDUCTED RF SPURIOUS EMISSION

Mode

Frequency (MHz)

b

2412

b

2437

b

2462

g

2412

g

2437

g

2462

n20

2412

n20

2437

n20

2462

n40

2422

n40

2437

n40

2452

Max Value (dBc) -44.14 -43.71 -43.61 -39.06 -38.64 -38.38 -38.81 -39.52 -39.04 -36.22 -36.59 -36.54

Project No.: ZHT-240425006E Page 72 of 85

Limit (dBc) -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20

Verdict Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass

Test Graphs Tx. Spurious NVNT b 2412MHz Ant1 Ref

Project No.: ZHT-240425006E Page 73 of 85

Tx. Spurious NVNT b 2412MHz Ant1 Emission

Tx. Spurious NVNT b 2437MHz Ant1 Ref

Project No.: ZHT-240425006E Page 74 of 85

Tx. Spurious NVNT b 2437MHz Ant1 Emission

Tx. Spurious NVNT b 2462MHz Ant1 Ref

Project No.: ZHT-240425006E Page 75 of 85

Tx. Spurious NVNT b 2462MHz Ant1 Emission

Tx. Spurious NVNT g 2412MHz Ant1 Ref

Project No.: ZHT-240425006E Page 76 of 85

Tx. Spurious NVNT g 2412MHz Ant1 Emission

Tx. Spurious NVNT g 2437MHz Ant1 Ref

Project No.: ZHT-240425006E Page 77 of 85

Tx. Spurious NVNT g 2437MHz Ant1 Emission

Tx. Spurious NVNT g 2462MHz Ant1 Ref

Project No.: ZHT-240425006E Page 78 of 85

Tx. Spurious NVNT g 2462MHz Ant1 Emission

Project No.: ZHT-240425006E Page 79 of 85
Tx. Spurious NVNT n20 2412MHz Ant1 Ref
Tx. Spurious NVNT n20 2412MHz Ant1 Emission

Project No.: ZHT-240425006E Page 80 of 85
Tx. Spurious NVNT n20 2437MHz Ant1 Ref
Tx. Spurious NVNT n20 2437MHz Ant1 Emission

Project No.: ZHT-240425006E Page 81 of 85
Tx. Spurious NVNT n20 2462MHz Ant1 Ref
Tx. Spurious NVNT n20 2462MHz Ant1 Emission

Project No.: ZHT-240425006E Page 82 of 85
Tx. Spurious NVNT n40 2422MHz Ant1 Ref
Tx. Spurious NVNT n40 2422MHz Ant1 Emission

Project No.: ZHT-240425006E Page 83 of 85
Tx. Spurious NVNT n40 2437MHz Ant1 Ref
Tx. Spurious NVNT n40 2437MHz Ant1 Emission

Project No.: ZHT-240425006E Page 84 of 85
Tx. Spurious NVNT n40 2452MHz Ant1 Ref
Tx. Spurious NVNT n40 2452MHz Ant1 Emission

12. TEST SETUP PHOTO Reference to the appendix I for details.
13. EUT CONSTRUCTIONAL DETAILS Reference to the appendix II for details.

Project No.: ZHT-240425006E Page 85 of 85

 END OF REPORT 



Related FCC IDs:

Search Any Device: