AirWave 8.3.0.1 Supported Devices Matrix
Supported Infrastructure Devices
Supported, Infrastructure, Devices
HPE Aruba
AirWave 8.3.0.1 Supported Devices Matrix
Jun 15, 2023 — AirWave Switch Configuration Guide. ... AirWave 8.2 introduces support for pairs of HP Unified Wired-WLAN (UWW) devices operating in HA mode.
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 25 Pages, 153.90KB
Document DEVICE REPORT
✖
AirWave 8.3.0.1 Supported Infrastructure Devices AirWave provides a range of features to manage network infrastructure devices from Aruba Networks and other vendors. This document describes the supported product families, software versions, and feature set for the following product sets: n Aruba Devices n Hewlett Packard Enterprise Devices n Other Third-Party Vendor Devices l Cisco® Devices l Juniper® Devices l Meru® Devices l Motorola® Devices l Other Third-Party Devices with Monitoring Support n Other Switches Aruba Devices This release of AirWave supports management of global configuration profiles or settings, monitoring, and software upgrades on the Aruba devices and software described in the following sections. ArubaOS AirWave supports all Aruba controllers and most access points (APs) that are running the following ArubaOS versions: n 6.4.4.0 n 6.5.0.0, 6.5.1.0, 6.5.2.0, 6.5.3.0, 6.5.4.0, 6.5.4.18, 6.5.4.20, 6.5.4.22, 6.5.4.23, and 6.5.4.24 n 8.0.0.0 and 8.0.1.0 n 8.1.0.x n 8.2.0.x and 8.2.1.x n 8.3.0.x n 8.4.0.x n 8.5.0.x n 8.6.0.21 n 8.7.0.x n 8.7.1.x n 8.8.0.x n 8.9.0.x n 8.10.0.7 n 8.11.0.x n 8.11.1.0 AirWave 8.3.0.1 | Supported Infrastructure Devices Rev. 01 | June 2023 AirWave also supports Aruba unified APs, which are APs factory-installed with ArubaOS 6.5.2.0 or a later. A unified AP can be configured to operate as either a campus AP or a remote AP when that device is first provisioned. For more information on unified APs, refer to the ArubaOS 6.5.2.0 Release Notes. FIPS Support ArubaOS 6.x supports FIPS for Aruba controllers, 7000 Series, 7200 Series, and 7280 models for ArubaOS version 6.5.4.24-FIPS. ArubaOS 8.x supports FIPS for Aruba controllers, 7000 Series, 7200 Series, 7280, and 9000 Series models for below ArubaOS versions. n 8.5.0.13-FIPS n 8.6.0.21-FIPS n 8.7.1.4-FIPS n 8.8.0.1-FIPS n 8.9.0.3-FIPS n 8.10.0.7-FIPS n 8.11.1.0-FIPS For the complete list of products that have reached the end of life milestone and are not supported, refer to http://www.arubanetworks.com/support-services/end-of-life/ Table 1 lists the supported devices and the tested ArubaOS firmware versions. Table 1: Supported ArubaOS Devices Device Validated Up To AP-503 8.11.1.0 AP-615 8.11.0.0 AP-655 8.10.0.0 AP-584, AP-585, AP-585EX, AP-587, and AP- 8.10.0.0 587EX AP-635 8.9.0.0 AP-565, AP-565EX, AP-567, and AP-567EX 8.8.0.0 AP-505H 8.8.0.0 AP-570 Series 8.8.0.0 AP-555 8.7.0.0 AP-534 and AP-535, 8.8.0.0 AP-514 and AP-515 8.7.0.0 AP-518 8.8.0.0 AP-504 and AP-505 8.8.0.0 AP-387 8.7.0.0 2 AirWave 8.3.0.1 | Supported Infrastructure Devices Device Validated Up To AP-374, AP-375, and AP-377 6.5.4.16, 8.8.0.0 AP-375ATEX 8.8.0.0 AP-365 and AP-367 6.5.4.16, 8.8.0.0 AP-344 and AP-345 with Dual 5-GHz Mode 8.8.0.0 AP-334 and AP-335 6.5.4.16, 8.8.0.0 AP-324 and AP-325 6.5.4.16, 8.8.0.0 AP-318 8.8.0.0 AP-314 and AP-315 6.5.4.16, 8.8.0.0 AP-304 and AP-305 6.5.4.16, 8.7.0.0 AP-303 8.8.0.0 AP-303H, and AP-303HR 6.5.4.16, 8.8.0.0 AP-303P 8.3.0.0 AP-277 6.5.4.16, 8.7.0.0 AP-274 and AP-275 6.5.4.16, 8.7.0.0 AP-228 6.5.4.16, 8.7.0.0 AP-224 and AP-225 6.5.4.16, 8.7.0.0 AP-214 and AP-215 6.5.4.16, 8.7.0.0 AP-207 6.5.4.16, 8.7.0.0 AP-205H 6.5.4.16, 8.7.0.0 AP-204 and AP-205 6.5.4.16, 8.7.0.0 AP-203H 6.5.4.16, 8.8.0.0 AP-203-R and AP-203RP 6.5.4.16, 8.8.0.0 AP-175 6.5.4.16, 8.6.0.0 AP-134 and AP-135 6.5.4.16, 8.6.0.0 AP-124 and AP-125 6.5.4.16, 6.4.0.0 AP-114 and AP-115 6.5.4.16, 8.6.0.0 AP-104 and AP-105 6.5.4.16, 8.6.0.0 AP-103 6.5.4.16, 8.6.0.0 AirWave 8.3.0.1 | Supported Infrastructure Devices 3 Device Validated Up To AP-103H 6.5.4.16, 8.3.0.0 AP-92 and AP-93 6.5.4.16, 8.2.0.0 AP-93H 6.5.4.16, 8.2.0.0 AP-68 6.5.4.16, 8.7.0.0 3000 Series Controller 6.4.4.22 7005 Controller 6.5.4.16, 8.7.0.0 7010 Controller 6.5.4.16, 8.7.0.0 7024 Controller 6.5.4.16, 8.7.0.0 7030 Controller 6.5.4.16, 8.7.0.0 7200 Series Controller 6.5.4.16, 8.7.0.0 7280 Controller 6.5.4.16, 8.7.0.0 9004 Branch Controller 8.7.0.0 9012 Branch Controller 8.7.0.0 9240, 9240 Silver, and 9240 Gold Controller 8.10.0.0 The End-Of-Life devices and ArubaOS versions listed on the EOL page http://www.arubanetworks.com/support-services/end-of-life/ are not tested or supported by AirWave. Aruba recommends deploying the devices only with the supported platforms and ArubaOS versions. Aruba Instant Table 2 lists the Instant firmware versions and functions supported by AirWave. AirWave also supports the Aruba RAP-100 Series and RAP-3 Series remote access points. Table 2: Supported Aruba Instant Firmware Versions and Functions Instant Version Template Config Support for Instant GUI Config Instant 8.11.1.0 AirWave 8.2.15.2 AirWave 8.2.15.2 Instant 8.11.0.0 AirWave 8.2.15.0 AirWave 8.2.15.0 Instant 8.10.0.0 AirWave 8.2.14.1 AirWave 8.2.14.1 Instant 8.9.0.0 AirWave 8.2.14.0 AirWave 8.2.14.0 Instant 8.9.0.0 AirWave 8.2.13.1 AirWave 8.2.13.1 4 AirWave 8.3.0.1 | Supported Infrastructure Devices Instant Version Template Config Instant 8.8.0.0 Instant 8.8.0.0 Instant 8.7.1.0 Instant 8.7.0.0 Instant 8.7.0.0 Instant 8.6.0.4 Instant 8.6.0.0 Instant 8.5.0.2 Instant 8.5.0.0 Instant 8.5.0.0 Instant 8.4.0.1 Instant 8.4.0.0 Instant 8.3.0.0 Instant 8.3.0.0 Instant 6.5.4.0 Instant 6.5.4.0 Instant 6.5.3.0 Instant 6.5.2.0 Instant 4.3.1.0 Instant 4.3.0.0 Instant 4.2.4.0 Instant 4.2.3.0 AirWave 8.2.13.0 AirWave 8.2.12.1 AirWave 8.2.12.0 AirWave 8.2.11.2 AirWave 8.2.11.1 AirWave 8.2.11.0 AirWave 8.2.10.1 AirWave 8.2.10.0 AirWave 8.2.9.1 AirWave 8.2.9.0 AirWave 8.2.8.2 AirWave 8.2.8.1 AirWave 8.2.7.1 AirWave 8.2.6.1 AirWave 8.2.5.1 AirWave 8.2.5.0 AirWave 8.2.4.1 AirWave 8.2.4.0 AirWave 8.2.3.1 AirWave 8.2.3.0 AirWave 8.2.1.0 AirWave 8.2.0.0 Support for Instant GUI Config AirWave 8.2.13.0 AirWave 8.2.12.1 AirWave 8.2.12.0 AirWave 8.2.11.2 AirWave 8.2.11.1 AirWave 8.2.11.0 AirWave 8.2.10.1 AirWave 8.2.10.0 AirWave 8.2.9.1 AirWave 8.2.9.0 AirWave 8.2.8.2 AirWave 8.2.8.1 AirWave 8.2.7.1 AirWave 8.2.6.1 AirWave 8.2.5.1 AirWave 8.2.5.0 AirWave 8.2.4.1 AirWave 8.2.4.0 AirWave 8.2.3.1 AirWave 8.2.3.0 AirWave 8.2.2.0 AirWave 8.2.2.0 n Starting with 6.4.3.x-4.2, Instant software does not support IAP-92 and IAP-93. n Management of FIPS enabled IAP is not supported on both non-FIPS & FIPS-enabled AirWave servers. AirWave 8.3.0.1 | Supported Infrastructure Devices 5 Aruba Switches AirWave supports monitoring, template configuration, and firmware changes on the Aruba switches listed in Table 3. On these switches, you can set up device-specific triggers and alerts and designate them as trap receivers. If you want to see the SNMP traps, go to the System > Syslog & Traps page. In addition, you can push a complete configuration profile using templates to Aruba switches that have a factory-default configuration, or you can send configuration jobs using switch CLI commands and snippets to switches in a device group. In VisualRF, these Aruba switches appear in the VisualRF product catalog. However, their utilization values will be 0 because AirWave does not get utilization values for these devices. Table 3: Supported Aruba Switches Device Monitoring Aruba 2530YA Switch Series Yes Aruba 2530YB Switch Series Yes Aruba 2540 Switch Series Yes Aruba 2620 Switch Series Yes Aruba 2920 Switch Series Yes Aruba 2930F Switch Series Yes Aruba 2930M Switch Series Yes Aruba 3800 Switch Series Yes Aruba 3810 Switch Series Yes Aruba 5400R zl2 Switch Series Yes ArubaOS-CX 4100 Switch Yes Series ArubaOS-CX 6000 Switch Yes Series ArubaOS-CX 6100 Switch Yes Series ArubaOS-CX 6200 Switch Yes Series ArubaOS-CX 6200v2 Switch Yes Series ArubaOS-CX 6300 Switch Yes Series ArubaOS-CX 6300M Switch Yes Series ArubaOS-CX 6400 Switch Yes Series Configuration Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Firmware Upgrade Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Validated Up To YA.16.11.0010 YB.16.11.0010 YC.16.11.0010 RA.16.11.0010 WB.16.11.0010 WC.16.11.0010 WC.16.11.0010 KA.16.11.0010 KB.16.11.0010 KB.16.11.0010 RL.10.11.1005 PL.10.11.1005 PL.10.11.1005 ML.10.11.1005 ML.10.11.1005 FL.10.11.1005 FL.10.11.1005 FL.10.11.1005 6 AirWave 8.3.0.1 | Supported Infrastructure Devices Device ArubaOS-CX 8100 Switch Series ArubaOS-CX 8320 Switch Series ArubaOS-CX 8325 Switch Series Aruba OS-CX 8360 Switch Series Aruba OS-CX 8400 Switch Series ArubaOS-CX 9300 Switch Series Aruba OS-CX 10000 Switch Series Monitoring Yes Yes Configuration No No Firmware Upgrade No No Validated Up To LL.10.11.1005 TL.10.11.1005 Yes No No GL.10.11.1005 Yes No No LL.10.11.1005 Yes No No XL.10.11.1005 Yes No No CL.10.11.1005 Yes No No DL.10.11.1005 AirWave 8.3.0.1 | Supported Infrastructure Devices 7 Aruba Mobility Conductor Appliances AirWave supports the following devices running ArubaOS 8.0.0.0 and later: n Mobility Conductor Hardware Appliance MM-HW-1K, MM-HW-5K, and MM-HW-10K n Mobility Conductor Virtual Appliance MM-VA Aruba Mobility Access Switches AirWave supports profile configuration, monitoring, and software upgrades on the Aruba Mobility Access Switches. In addition to the port statistics supported for most Ethernet switches with the supported firmware described below, AirWave also tracks the activity of authenticated wired clients on Aruba switches. Table 4: Supported Aruba Mobility Access Switches Device Validated up to S1500 7.4.0.0 S2500 S3500 7.4.0.0 7.4.0.0 Aruba AirMesh Aruba AirMesh outdoor products running MeshOS 4.2 are supported for monitoring and software upgrades. Table 5: Supported Aruba MeshOS Devices Device Validated up to MSR1200 MeshOS 4.2 MSR2000 MeshOS 4.2 MSR4000 MeshOS 4.2 MST200 MeshOS 4.2 Hewlett Packard Enterprise Devices The firmware versions for the HPE devices listed in Table 6 represent the latest firmware version verified as fully supported by AirWave 8.3.0.1. You can select these supported wireless devices in the VisualRF. You can set up these devices to send traps to AirWave and view the SNMP traps on the System > Syslog & Traps page. AirWave supports switch configuration only for the following: n Mobility Access Switches running ArubaOS (AOS) 7.2.0.0 or higher n Switches running AOS 16.01 or higher For more information on configuring and managing MAS and AOS-S switches via AirWave, refer to the AirWave Switch Configuration Guide. 8 AirWave 8.3.0.1 | Supported Infrastructure Devices n AirWave does not support MSM APs running in autonomous mode. n Informal testing shows that AirWave supports some devices running more recent versions of firmware, but full support for these later versions is not guaranteed. Table 6: HPE Device Support Model MSM310 and MSM310R MSM313 and MSM313R MSM317 MSM318 MSM320 and MSM320R MSM323 and MSM323R MSM325 MSM335 MSM410 MSM417* MSM422 MSM425* MSM430 MSM460 MSM466 and 466R MSM525* MSM527* MSM560* MSM710 Controller MSM720 Controller MSM730 Controller MSM750 Controller MSM760 Controller MSM765 Controller Firmware Validated Up To 6.5.1.0 6.5.10 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 6.5.1.0 AirWave 8.3.0.1 | Supported Infrastructure Devices 9 Model ProCurve 420 ProCurve 530 ProCurve 2626-PWR 830 Unified Wired-WLAN Switch* 850 Unified Wired-WLAN Switch* 870 Unified Wired-WLAN Switch* HPE WESM controllers & APs xl HPE WESM controllers & APs zl HPE 1405 Switch Series HPE 1420 Switch Series HPE 1620 Switch Series HPE 1820 Switch Series HPE 1850 Switch Series HPE 1910 Switch Series HPE 1920 Switch Series HPE 1950 Switch Series HPE 3100 Switch Series HPE 3600 Switch Series HPE 5120 Switch Series HPE 5130 Switch Series HPE 5140 EI Switch Series HPE 5140 HI Switch Series HPE 5500 Switch Series HPE 5510 HI Switch Series HPE 5520 HI Switch Series HPE 5700 Switch Series HPE 5710 Switch Series HPE 5800 Switch Series 10 Firmware Validated Up To 2.0.38 - 2.2.5 WA.01.16-WA.02.19 H.10.35 (ROM H.08.02) 5.20.109 (Release 2607P39) 5.20.109 (Release 2607P39) 5.20.109 (Release 2607P39) WS.01.05 WS.02.19 WT.01.03 WT.01.28 ** ** ** ** ** ** ** 2220P02 (Comware 7) 2220P02 (Comware 7) 2220P02 (Comware 7) 2220P02 (Comware 5) 2220P02 (Comware 7) 2220P02 (Comware 7) 2220P02 (Comware 7) 2220P02 (Comware 5) ** 2220P02 (Comware 7) ** 7.1.070 (Release 2612P08) ** AirWave 8.3.0.1 | Supported Infrastructure Devices Model Firmware Validated Up To HPE 5820 Switch Series 1810P13 (Comware 7) HPE 5900 Switch Series 2220P02 (Comware 7) HPE 5945 Switch Series 7.1.070 (Release 6555P01) HPE 7500 Switch Series 2220P02 (Comware 7) HPE 7500X Switch Series 2220P02 (Comware 7) HPE 7900 Switch Series ** HPE 10500 Switch Series 2220P02 (Comware 7) HPE 12900E Switch Series ** * Not supported in VisualRF. **Limited testing done. Contact Technical Support for help with any issues. High Availability Support AirWave 8.2 introduces support for pairs of HP Unified Wired-WLAN (UWW) devices operating in HA mode. AirWave monitors the status of each controller. After AirWave detects that a failover occurred and the APs failed over to the backup controller, AirWave displays the current status of the APs. Monitoring Support AirWave provides monitoring through SNMP polling with the OIDS listed in the following table. Table 7: Monitoring Support Model SNMP Object ID SysOID HPE 7502 Switch 1.3.6.1.4.1.25506.11.1.1 .1.3.6.1.4.1.25506.11.1.269 HPE 7503S Switch 1.3.6.1.4.1.25506.11.1.2 .1.3.6.1.4.1.25506.11.1.268 HPE 7503 Switch 1.3.6.1.4.1.25506.11.1.3 .1.3.6.1.4.1.25506.11.1.270 HPE 7506 Switch 1.3.6.1.4.1.25506.11.1.4 .1.3.6.1.4.1.25506.11.1.267 HPE 7506-V Switch 1.3.6.1.4.1.25506.11.1.5 .1.3.6.1.4.1.25506.11.1.264 HPE 7510 Switch 1.3.6.1.4.1.25506.11.1.6 .1.3.6.1.4.1.25506.11.1.271 HPE 9505 Switch 1.3.6.1.4.1.25506.11.1.39 .1.3.6.1.4.1.25506.11.1.266 HPE 9508-V Switch 1.3.6.1.4.1.25506.11.1.40 .1.3.6.1.4.1.25506.11.1.265 HPE 9508 Switch 1.3.6.1.4.1.25506.11.1.41 .1.3.6.1.4.1.25506.11.1.272 HPE 9512 Switch 1.3.6.1.4.1.25506.11.1.43 .1.3.6.1.4.1.25506.11.1.144 HPE 10504 Switch 1.3.6.1.4.1.25506.11.1.86 .1.3.6.1.4.1.25506.11.1.229 HPE 10508 Switch 1.3.6.1.4.1.25506.11.1.87 .1.3.6.1.4.1.25506.11.1.230 AirWave 8.3.0.1 | Supported Infrastructure Devices 11 Model HPE 10508-V Switch HPE 10512 Switch HPE Switches HPE Routers HPE Wireless HPE Security HPE (3Com) S7503E-M HPE (3Com) S7502 HPE (3Com) S7502E HPE (3Com) S7502ESX HPE (3Com) S7503 HPE (3Com) S7503E HPE (3Com) S7503E-S HPE (3Com) S7503X HPE (3Com) S7503X-G HPE (3Com) S7504EXS HPE (3Com) S7506 HPE (3Com) S7506E HPE (3Com) S7506E-S HPE (3Com) S7506E-V HPE (3Com) S7506E-X HPE (3Com) S7506X-G HPE (3Com) S7506X-R HPE (3Com) S7508E-X HPE (3Com) S7510E HPE (3Com) S7510E-X HPE (3Com) S7510X HPE FlexNetwork 5130 HI Switch Series SNMP Object ID 1.3.6.1.4.1.25506.11.1.88 1.3.6.1.4.1.25506.11.1.89 *.25506.11.1 * *.25506.11.2 * *.25506.11.3* *.25506.11.4 * 1.3.6.1.4.1.25506.1.1504 1.3.6.1.4.1.25506.1.52 1.3.6.1.4.1.25506.1.207 1.3.6.1.4.1.25506.1.1309 1.3.6.1.4.1.25506.1.53 1.3.6.1.4.1.25506.1.208 1.3.6.1.4.1.25506.1.370 1.3.6.1.4.1.25506.1.1560 1.3.6.1.4.1.25506.1.1836 1.3.6.1.4.1.25506.1.1308 1.3.6.1.4.1.25506.1.54 1.3.6.1.4.1.25506.1.209 1.3.6.1.4.1.25506.1.469 1.3.6.1.4.1.25506.1.210 1.3.6.1.4.1.25506.1.1306 1.3.6.1.4.1.25506.1.1837 1.3.6.1.4.1.25506.1.55 1.3.6.1.4.1.25506.1.636 1.3.6.1.4.1.25506.1.159 1.3.6.1.4.1.25506.1.1307 1.3.6.1.4.1.25506.1.1562 1.3.6.1.4.1.25506.11.1. (184 185 186 187 188 189 190 191 192 193 194 195 SysOID .1.3.6.1.4.1.25506.11.1.145 .1.3.6.1.4.1.25506.11.1.231 .1.3.6.1.4.1.25506.11.1.232 NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA 12 AirWave 8.3.0.1 | Supported Infrastructure Devices Model HPE FlexNetwork 5140 EI Switch Series HPE FlexNetwork 5140 HI Switch Series HPE FlexNetwork 5520 HI Switch Series HPE FlexNetwork 5600 HI Switch Series HPE FlexNetwork 7500X Switch Series SNMP Object ID 196 197 198 199 200 201 202 203 208 209 210 211 244) NA SysOID NA NA NA NA NA NA NA 1.3.6.1.4.1.25506.11.1.(1 2 3 4 5 6 256) NA Configuration and configuration backup features are not supported in the above listed devices. Limited testing is done with simulated devices. HPE ProCurve HPE ProCurve switches have the following additional support through AirWave: n Automated discovery through SNMP n Model & software version identification Other Third-Party Vendor Devices AirWave supports the following monitoring features for other third party devices: n User monitoring data such as connection time, user name, SSID, and bandwidth n Network monitoring data, including real-time and historical bandwidth and user count metrics n Rogue detection and classification using AirWavecustomizable rules n VisualRF heatmaps and user/rogue location n Reports n Triggers and alerts In some cases, you can do basic configuration and firmware upgrades, as well as discover third-party controller and APs. Cisco® Devices AirWave supports Cisco devices that are running the latest verified firmware versions and have not reached the end of life milestone. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not validated. Cisco Autonomous Access Points AirWave provides monitoring, management, and software upgrade support for the devices listed in Table 8. AirWave 8.3.0.1 | Supported Infrastructure Devices 13 Table 8: Supported Cisco Autonomous Access Points Model Validated up to 350 Series IOS 12.3(11)JA and IOS 12.4(21a)JA1 Access Points 702 Series IOS: 15.3(3)JD Access Points 801 Series Integrated Access Points IOS 12.4(25d)JA2 and IOS 15.(22)JB 819 Series Integrated Service Routers IOS 15.6.3M5 860 Series IOS 12.4(15)XZ, 12.4(20)T Access Points 881 Series IOS 12.4(21a)JA1 Access Points 881W Series IOS 12.4(21a)JA1 and IOS 15.0(1)M7 Access Points 881GW Series Access Points IOS 12.4(21a)JA1 and IOS 15.1(4)M3 891 Series IOS 12.4(21a)JA1 and IOS 15.0(1)M7 Access Points 1040 Series IOS 12.4(21a)JA1 Access Points 1100 Series IOS 12.4(21a)JA1 Access Points 1110 Series IOS 12.4(21a)JA1 and IOS 12.3(11)JA Access Points 1130 Series IOS 12.4(21a)JA1 Access Points 1140 Series IOS 12.4(21a)JA1 and IOS 12.3(11)JA Access Points 1200 Series IOS 12.4(21a)JA1 and IOS 12.3(11)JA Access Points 1210 Series IOS 12.4(21a)JA1 Access Points 1230 Series IOS 12.4(21a)JA1 Access Points 14 AirWave 8.3.0.1 | Supported Infrastructure Devices Model Validated up to 1240 Series IOS 12.4(21a)JA1 Access Points 1250 Series IOS 12.4(21a)JA1 Access Points 1260 Series IOS 12.4(21a)JA1 Access Points 1300/1400 Series Bridges IOS 12.4(21a)JA1 1700 Series IOS 10.2.111.0 (IOS: 15.3(3)JN3) Access Points 1941W Series IOS 15.2(3)T Access Points 2700 Series IOS 10.2.111.0 (IOS: 15.3(3)JN3) Access Points Cisco Wireless Controllers and Access Points AirWave supports monitoring, RAPIDS, device discovery, and VisualRF for these devices, as well as configuration, firmware identification, AMP upgrade, and client monitoring-diagnostics for wireless controllers. Table 9 lists the Cisco wireless controllers and access point platforms that are supported in this release. Table 9: Supported Cisco Wireless Controllers and Access Points Model Validated up to 1040 Series Access Points 8.3.102.0 1130 Series Access Points 7.6.110.0 (Bootloader: 7.0.116.0) 1140 Series Access Points 8.3.102.0 1200 Series Access Points 8.3.102.0 1550 Series Access Points 8.3.102.0 1600 Series Access Points 8.3.102.0 1700 Series Access Points 8.3.102.0 1800 Series Access Points 8.3.102.0 AirWave 8.3.0.1 | Supported Infrastructure Devices 15 Model Validated up to 2600 Series Access Points 8.3.102.0 2700 Series Access Points 8.3.102.0 2802 Series Access Points 8.5.110.0 3500 Series Access Points 8.3.102.0 3600 Series Access Points 8.3.102.0 3700 Series Access Points 8.3.102.0 3800 Series Access Points 8.3.102.0 2100 Series Wireless Controllers 7.0.235.0 (Bootloader: 7.0.235.0) 2500 Series Wireless Controllers 8.3.102.0 4400 Series Wireless Controllers 7.0.235.0 (Bootloader: 7.0.235.0) Aironet 4800 Series Bridges (pre-VxWorks, monitoring only) 8.65_2 5508 Wireless Controllers 8.5.110.0 5520 Wireless Controllers 8.1.131.0 5760 Wireless Controllers 3.2.0 Flex 7500 Controllers 8.3.102.0 8510 Controllers 8.5.110.0 3504 Wireless Controllers 8.10.130.0 (Bootloader: 8.5.103.0) Catalyst 9800-40 16.12.4a Series 16 AirWave 8.3.0.1 | Supported Infrastructure Devices Model Cisco Catalyst 9800-80 Cisco Catalyst 9800-CL Wireless Controller for Private Cloud Cisco Catalyst 9800-L-C Cisco Catalyst 9120 AXI Cisco Catalyst 9120 AXE Cisco Catalyst 9130 AXI Cisco Catalyst 9130 AXE Cisco Catalyst 9105 AXW Validated up to Limited testing done with simulator. Limited testing done with simulator. Limited testing done with simulator. 8.10.151.0 8.10.151.0 Limited testing done with simulator. Limited testing done with simulator. Limited testing done with simulator. Cisco Mobility Services Engine and 500 Series Access Points are not supported. The RLAN feature is not supported for Cisco Catalyst 9105 AXW. Cisco Switches AirWave supports automated discovery through SNMP, model and firmware version identification, and displays CDP neighbor information and extended port error statistics for the Cisco switches listed in Table 10. Table 10: Supported Cisco Switches Model Validated up to C9800-L-F-K9 16.12.3 Catalyst 9400 Series Swtiches 16.06.03 Catalyst 2900 Series Switches (monitoring only) 15.0(2)SE11 Catalyst 3650 Series Switches 03.06.06E Catalyst 3750 Series Switches 12.2(55)SE11 Catalyst 3850 Series Switches 03.06.06E Industrial Ethernet 4000 Series Switches 15.2(4)EA5 AirWave 8.3.0.1 | Supported Infrastructure Devices 17 AirWave doesn't update the upstream device information for access points connected to Cisco switches when Cisco switches are polled when using SNMPv3. Cisco has restricted access to the BRIDGE-MIB when using SNMPv3. When you access a Cisco switch using SNMPv3, APs connected to that switch may not be able to show upstream device info. As a workaround to this issue, add SNMPv3 bridge commands to the Cisco switches in order to expose VLAN values for the MIB polled by UDT. If there are devices on a switch, add the following command for each VLAN-#: snmp-server group <GroupName> v3 priv context You may need to append views to the command, as follows: snmp-server group <GroupName> v3 priv context <VLAN-#> read <ViewName> Use the match prefix parameter to all existing VLANs: n snmp-server group <GroupName> v3 priv context vlan- match prefix n snmp-server group <GroupName> v3 priv context vlan- match prefix access Juniper® Devices The following Juniper controllers and APs are supported for monitoring, configuration, and software upgrades. The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.3.0.1. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed. Table 11: Supported Juniper Access Points and Wireless LAN Controllers Model Validated up to WLA321 9.1.0.6.0 Access Points WLA322 9.1.0.6.0 Access Points WLA522 9.1.0.6.0 Access Points WLA532 9.1.0.6.0 Access Points WLA632 9.1.0.6.0 Access Points WLC100 Wireless LAN Controllers 9.1.0.6.0 WLC2 Wireless LAN Controllers 9.1.0.6.0 WLC2800 Wireless LAN Controllers 9.1.0.6.0 18 AirWave 8.3.0.1 | Supported Infrastructure Devices Model Validated up to WLC8 Wireless LAN Controllers 9.1.0.6.0 WLC800 Wireless LAN Controllers 9.1.0.6.0 WLC880 Wireless LAN Controllers 9.1.0.6.0 WLC JunosV Wireless LAN Controllers 9.1.0.6.0 Juniper Switch 12.3R6.6 Juniper® Juniper switches have the following additional support through AirWave: n Automated discovery through SNMP n Model & software version identification n Rogue AP detection is supported using the Q-BRIDGE MIB Meru® Devices The following Meru controllers and APs are now supported in VisualRF. The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.3.0.1. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed. Table 12: Meru Device Support Model Validated up to AP302 6.1.1-25 AP320i 6.1.1-25 AP332i 6.1.1-25 AP433i 6.1.1-25 AP433is 6.1.1-25 AP822e 6.1.1-25 AP822i 6.1.1-25 AP832e 6.1.1-25 AirWave 8.3.0.1 | Supported Infrastructure Devices 19 Model Validated up to AP832i 6.1.1-25 RS4000 6.1.1-25 MC1000* 3.6.1-49 MC1550 6.1.1-25 MC3000* 3.6.1-49 MC3200 6.1.1-25 MC4200 6.1.1-25 MC5000* 3.6.1-49 FWC-200D 3.6.1-49 FWC-500D 3.6.1-49 *This version of AirWave supports monitoring for these devices. VisualRF support for the for the AP433i, AP433e, AP433is, AP822i, and AP822e is not included in this release of AirWave. Motorola® Devices The following Motorola (formerly Symbol) controllers and autonomous APs are supported for monitoring, configuration, and software upgrades. The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.3.0.1. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed. Table 13: Motorola Autonomous AP, Wireless LAN Controller, and AP Support Model Validated up to AP621 5.4.2.0-030R AP622 5.4.2.0-030R AP650 5.4.2.0-030R AP5131 5.4.2.0-030R AP5181 5.4.2.0-030R AP6521* 5.4.2.0-030R AP6522* 5.4.2.0-030R 20 AirWave 8.3.0.1 | Supported Infrastructure Devices Model Validated up to AP6532* 5.7.0.0-057R AP7131 5.4.2.0-030R AP7161 5.4.2.0-030R AP7532 5.8.1.0-012R NX9600 5.8.6.0-011R RFS4000 5.4.2.0-030R RFS6000 5.4.2.0-030R RFS7000 5.4.2.0-030R WS2000 2.4.5 WS5100 3.3.4 Wing5 RFS controllers 5.4.2.0-030R * These AP and controller models may require adjustments to the AirWave SNMP timeouts to compensate for known SNMP issues on these devices. Other Third-Party Devices with Monitoring Support This version of AirWave supports monitoring for a variety of devices with software versions listed in the table below. The firmware versions listed in the table below represents the latest firmware version verified as fully supported by AirWave 8.3.0.1. Informal testing shows that AirWave supports devices running more recent versions of firmware, but full support for these later versions is not guaranteed. Table 14: Other Supported Devices Device Validated up to Arista DCS-7504N and DCS7280SRAM-48C6 switches 4.21.7M BelAir 200 main.2005.03.29 Brocade ICX switches 08.0.20T211 and 08.0.30aT213 Ericsson APM-210 Access Point Modules 6.4.4.0-sp Proxim AP-600/700 2.0 4.0.2 Proxim AP 2000/4000 2.0 4.0.2 AirWave 8.3.0.1 | Supported Infrastructure Devices 21 Device Validated up to Proxim Tsunami MP.11 QB 2.3.0 4.0.0 954-x, 2454-x, 4954-x, 5054-x Siemens SCALANCE W1750D 6.5.0.0 - 4.3.0 Siemens SCALANCE XC208G 4.1 switches Siemens SCALANCE XR500 switches 6.1.3 Siemens SCALANCE XR300 switches 3.2.1 Symbol 3021 04.01-23 04.02-19 Symbol 4121 and 4131 3.51-20 3.95-04 Symbol 5131/5181 1.1.0.0.045R 2.5.0.0 Trapeze MXR-2, MXR-8, MXR20, MXR-2xx, MX-400, MP-3x2, and MP-422 5.0.12.2 7.0.5.6 Tropos 3/4/5210/5320/9422/9532 5.1.4.7 6.6.1.3 Other Switches Some switches have additional support in AirWave: Alcatel-Lucent OmniSwitchTM (6250 and 6450) n Automated discovery through SNMP n Model & software version identification n Stack information n Firmware version 6.6.1.859.R01 Brocade n Automated discovery through SNMP n Model & software version identification n Firmware version 08.0.20T211 and 08.0.30aT213 n Stacking Force10 n Model & software version identification n Firmware version 8.4.2.9 Siemens Ruggedcom n Zero Packet Loss Technology n Robust and Reliable 22 AirWave 8.3.0.1 | Supported Infrastructure Devices n Model & software version identification AirWave 8.2.12.1 supports the following Siemens Ruggedcom models: Layer 2 Rack Switches n RSG2100 n RSG2100P n RST2228 n RST2228P Layer 2 Compact Switches n RS900GP n RSG920P n RSG908C n RSG910C n RSG907R n RSG909R n RST916P n RST916C Layer 3 Multi-service Platform RX 1500/1501/1510/1511/1512/1524/1536 RX 5000 Layer 3 Edge Router RX1400 Firmware Version Boot n v4.3.0 n ROS v5.4.2 n ROX v2.13.3 Only limited testing has been performed on Seimens Ruggedcom devices. Terminology Change As part of advancing HPE's commitment to racial justice, we are taking a much-needed step in overhauling HPE engineering terminology to reflect our belief system of diversity and inclusion. Some legacy products and publications may continue to include terminology that seemingly evokes bias against specific groups of people. Such content is not representative of our HPE culture and moving forward, Aruba will replace racially insensitive terms and instead use the following new language: Usage Campus Access Points + Controllers Old Language Master-Slave New Language Conductor-Member AirWave 8.3.0.1 | Supported Infrastructure Devices 23 Usage Instant Access Points Switch Stack Wireless LAN Controller Firewall Configuration Types of Hackers Old Language Master-Slave Master-Slave Mobility Master Blacklist, Whitelist Black Hat, White Hat New Language Conductor-Member Conductor-Member Mobility Conductor Denylist, Allowlist Unethical, Ethical 24 AirWave 8.3.0.1 | Supported Infrastructure Devices Contacting Support Main Site arubanetworks.com Support Site asp.arubanetworks.com Airheads Social Forums and Knowledge community.arubanetworks.com Base North American Telephone 1-800-943-4526 (Toll Free) 1-408-754-1200 International Telephone arubanetworks.com/support-services/contact-support/ Software Licensing Site lms.arubanetworks.com End-of-life Information arubanetworks.com/support-services/end-of-life/ Security Incident Response Team (SIRT) Site: arubanetworks.com/support-services/security-bulletins/ Email: [email protected] © Copyright 2023 Hewlett Packard Enterprise Development LP 25 www.arubanetworks.com 6280 America Center Drive San Jose, CA 95002 Phone: 1-800-WIFI-LAN (+800-943-4526) Fax 408.752.0626 AirWave 8.3.0.1 | Supported Infrastructure Devicesmadbuild