49064 Dec17

cdoll

Instruction Manual P-60 / Sixty Special Poppers

P-60 / Sixty Special Poppers. Model No. 2085, 2656, 2086, 1866 ... Read and understand operator's manual and all other safety instructions.

Instruction Manual P-60 / Sixty Special Poppers - Gold Medal ...

Flavacol (Salt) Amount: Use small Flavacol scoop provided. Premeasure all ingredients (adjust as needed for desired taste), or for best results use Mega‐Pop ...

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 27 Pages, 3.23MB

Document DEVICE REPORT1866 2085 2086 2656 P-60 Sixty Special Poppers 49064
Instruction Manual
P-60 / Sixty Special Poppers
Model No. 2085, 2656, 2086, 1866

Model: 2085, 2656

Model: 2086, 1866

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
© 2017 Gold Medal Products Co.

Part No. 49064

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

SAFETY PRECAUTIONS

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.
008_051514

DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.
014_020416

WARNING
To avoid burns, DO NOT touch the kettle or any heated surface. DO NOT place or leave objects in contact with heated surfaces.

013_092414

WARNING
ALWAYS wear safety glasses when servicing this equipment.

010_010914

WARNING
No user serviceable parts inside. Refer servicing to qualified service personnel.
011_051514

WARNING
Read and understand operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Page 2

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

SAFETY PRECAUTIONS (continued)

WARNING
DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation.
012_010914

WARNING
This machine is NOT to be operated by minors.

007_010914

Note: Improvements are always being made to Gold Medal's equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal's Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only.

Page 3

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
2085: Sixty Special 6 oz. Popper, unit has a red dome. 2656: Ultra Sixty Special 6 oz. Popper unit equipped with a PowerOffTM Control feature,
heavy duty doors, and a red dome.
2086: P-60 6 oz. Popper; copper colored. 1866: P-60 6 oz. Popper unit equipped with a PowerOffTM Control feature; copper colored.
Items Included with this Unit

Aluminum Scoop Flavacol Measure

(PN 2071)

6.5 cc (PN 47678)

6 oz. Corn Measure (PN 49049)

Instruction Manual

Registration Warranty Card

Black Crutch Tip (PN 49123) one tip

Knob (PN 47120) Tee Bolt (PN 75267) (for Popper Doors)

Knob (PN 47120) Screw (PN 42227) (for Old Maid Pan)

Page 4

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to operation. Remove accessories and carefully remove kettle packed in cabinet interior.
2. Place unit on a sturdy, level base.
3. Unit has 4 glide feet preinstalled at the factory (see image below). Install a Black Crutch Tip on each foot. Firmly push crutch tip over glide until it covers glide entirely.
4. Tilt kettle and insert into hanger arms, then allow kettle to return naturally to an upright position (see image below).
5. Plug kettle lead into receptacle located on ceiling of cabinet interior. Align keyed or hook shaped prong with the correct opening, then push plug all the way in and twist or rotate to lock in place. To unplug, untwist kettle plug before attempting to pull from receptacle.
6. Door knobs are shipped in accessories pack. Install a door knob with tee bolt on each popper door; install knob with screw on old maid pan.
7. After setup, unit should be cleaned prior to use (see Care and Cleaning section).

Glide (pre-installed at the factory)
Black Crutch Tip
General images shown for reference only.

Kettle lead shown plugged into kettle receptacle.
Kettle shown mounted in hanger arms.

Page 5

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Electrical Requirements
The following power supply must be provided: 2085, 2086, 1866: 120 V~, 1220 W, 60 Hz 2656: 120 V~, 1300 W, 60 Hz

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.'s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.

CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Page 6

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

OPERATING INSTRUCTIONS
Controls and Their Functions
KETTLE HEAT SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the heating element in the kettle. The green switch light ON indicates there is power to the kettle heating element.
KETTLE MOTOR SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor. The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or un- popped) in the kettle.
LIGHTS/WARMER SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the interior cabinet light and corn pan heat element.

Kettle Heat Switch

Lights/Warmer

Kettle Motor Switch Switch

Label used on Models with PowerOff Control feature.

POWEROFF CONTROL (Model 2656 and 1866) The PowerOff Control feature will automatically turn the kettle heat off after 15 minutes of idle time (no popcorn popped). The PowerOff Control will prevent the heat element and thermostat from cycling OFF-ON if the Kettle Heat Switch is left on. This feature saves electrical power and extends the life of the kettle heating element and thermostat.
 When the Kettle Heat Switch is turned ON, and the kettle thermostat switches OFF, the PowerOff Control's 15 minute timer starts; the 15 minute timer resets each time a batch of popcorn is popped.
 The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate the kettle has been automatically turned OFF.
 To restart the kettle heating, cycle the Kettle Heat Switch OFF-ON.

Page 7

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Popping Corn Instructions
This section describes instructions for popping Salted Popcorn. The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in the kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers.
Popping Salted (Standard) Popcorn
Raw Popcorn Charge: Use corn measure provided (ex: for 6 oz. Kettle, use 6 oz. corn) Recommended Oil Volume: Oil volume is approx. 30% of corn amount (ex: for 6 oz. corn, use 2 oz. oil)
Flavacol (Salt) Amount: Use small Flavacol scoop provided
Premeasure all ingredients (adjust as needed for desired taste), or for best results use Mega-Pop® premeasured popcorn and oil pouch made for your kettle size.
1. Turn all switches ON. 2. To determine when kettle is ready to pop corn (about 4 minutes), test pop three
kernels of corn in one ounce (30 ml) of popping oil. When kernels pop, kettle is ready. 3. Lift kettle lid, pour in popcorn and Flavacol, then add oil; close lid. 4. When corn has finished popping, gently dump the popcorn.
Popping Tip: On final batch, turn Kettle Heat Switch OFF just as lids are forced open by the popping corn (kettle has plenty of heat to finish popping). This helps eliminate smoke/odor from any oil residue remaining in kettle.
5. When finished popping, turn KETTLE HEAT and KETTLE MOTOR switches OFF. NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN! Units with an auto kettle heat shut off feature will automatically shut kettle heat OFF after 15 min. of idle time (no popcorn popped). To restart heating, cycle the Heat Switch OFF-ON.

Page 8

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Care and Cleaning

DANGER
Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug the equipment before cleaning or servicing.
025_111616

WARNING
To avoid serious burns, DO NOT touch the kettle while it is hot!

028_082715

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product.
Note: It is extremely important to follow all of the cleaning procedures, otherwise parts damage and equipment failure will result. The warranty does not cover parts that are damaged due to improper cleaning.
Daily Kettle Cleaning Instructions
CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool at least 1 hour before attempting to clean. DO NOT use ice or water to cool down a hot kettle! Severe kettle damage will result!
1. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven cleaners or abrasive materials as they will damage the kettle.
2. Every night, mix Gold Medal's Heat'n Kleen solution (Item No. 2095), 2 tablespoons per gallon of water. It is not necessary to use the entire gallon at once; only use enough to fill the kettle 1/2 inch deep.
3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF. 4. Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the
inside of the kettle with a clean cloth. Make sure all of the solution goes into the bucket; do not spill any in the interior of the machine. For extra dirty kettles, the process may be repeated; or, after turning the kettle heat OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution into a bucket and wipe the inside of the kettle with a clean cloth. 5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result.

Page 9

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Daily Unit Cleaning Instructions
1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean. 2. Make sure to clean all pans/accessories in order to sanitize them before each use. 3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet. 4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine. 5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No. 2588) is recommended. Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588).

Page 10

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Troubleshooting

Issue
No Power to the Unit Kettle Does Not Heat
Long Popping Cycles (Longer than 4 minutes for Salt Popcorn)
Kettle Agitator Shaft not Rotating If the kettle agitator shaft is not rotating, DO NOT pop corn.

Possible Cause
A. No Power to the Unit A. Power to the Kettle B. Kettle Heat Switch C. PowerOff Control
D. Heating Element A. Low Voltage B. Inadequate Supply Lines
C. Inferior Corn
A. Kettle Motor Switch
B. Kettle Agitator Shaft/Stir Blade not rotating. (Unit must be OFF, unplugged and cool prior to checking or adjusting the agitator assembly.)

Solution
A. Make sure the unit's power cord is plugged in.
A. Make sure kettle lead-in cord is plugged in and twisted to lock into the kettle receptacle.
B. Have a qualified service person check the voltage to and from the Kettle Heat Switch; if switch is defective, replace it.
C. Units with the PowerOff Control feature, kettle heat will automatically shut OFF after 15 minutes of idle time (no popcorn popped). The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate the kettle has been automatically turned OFF.
To restart kettle heating, cycle the Heat Switch OFF-ON. Reference the Controls and Their Functions section of this manual.
D. Heating element in the kettle may be burned out. Check with a qualified service person for inspection/repair.
A. If the machine is operated on low voltage, this could cause the kettle not to reach the proper operating temperature. Check with a qualified electrician.
B. Inadequately sized electrical supply lines or use of extension cord, in addition to being a fire hazard, would also prevent the kettle from reaching the proper operating temperature. Check with a qualified electrician.
C. Inferior quality corn would result in longer popping cycles. Use only top quality hybrid popcorn from reputable suppliers. Even then, if you let your corn pick up moisture or dry out, your popping cycles will be slow.
A. Make sure the Kettle Motor Switch is ON. If the switch is ON, and the shaft is not rotating, the switch or motor may be faulty, contact qualified service personnel for inspection/repair.
B. Kettles with a FLOATING Stir Rod ­ lift the agitator weight and check the clearance between the shaft and the kettle bottom; it should be a minimum of 1/32" (thickness of a dime).
To make shaft adjustments, reference the Agitator Set Collar Adjustment section.

Page 11

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Agitator Set Collar Adjustment
The following instructions describe how to properly adjust set collars on an agitator assembly with a floating stir rod.
Agitator Assembly with a FLOATING Stir Rod

Steps to Adjust Set Collars

Gear Block

Step 1: Turn machine OFF, unplug unit, and allow it to cool completely before attempting to adjust the agitator height.

Needle Bearing (should set at least halfway into Gear Block)

Step 2: Loosen the set screw in each set collar Agitator's Spur Gear

to be adjusted.

(should set halfway up on

Drive Motor Spur Gear)

Step 3: With the kettle mounted in the popper,

Drive Motor Spur Gear

adjust the shaft so the Spur Gears are halfway

engaged, and the Needle Bearing is at least

halfway engaged in the gear block (reference

image at right).

Set Collar

DO NOT set spur gears at full gear contact; it

w/Set screw

can cause binding as the kettle is dumped.

Spur Gear Placement

Step 4: Snug tighten only, the set screw in set

collar above the crossbar to hold position. Then,

lift the agitator weight and check the clearance

between the shaft and the kettle bottom. If

there is adequate clearance, fully tighten the set

screw to secure set collar in place.

Step 5: Adjust clearance between the bottom of the crossbar and the lower set collar to 1/32" (thickness of a dime); then re-tighten set screw to secure in place (reference image).

Agitator Shaft

Step 6: Adjust set collar for agitator weight to

be between 3/16" to 1/4" above the agitator

weight. Once adjusted,

re-tighten set screw

to secure in place.

Adjust clearance to

thickness of a dime.

Agitator shown for general image reference only (lids not shown for clarity).

3/16" to 1/4" max.

Set Collar above Crossbar Crossbar
Lower Set Collar (below Crossbar) Set Collar (for Agitator Weight) Agitator Weight
Stir Rod

Page 12

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR.
027_010914

Page 13

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit. 3. When ordering, please include part number, part name, and quantity needed. 4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order. 5. Address all parts orders to:
Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: (800) 543-0862 (513) 769-7676
Fax: (800) 542-1496 (513) 769-8500
E-mail: [email protected] Web Page: gmpopcorn.com

Page 14

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Replacing Broken Glass
Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be obtained from a local glass shop, always purchase tempered glass.
GLASS DIMENSIONS (Height x Width x Thickness) Front Glass: 22 3/8" X 16 15/16" X 1/8" (1 Piece) Side Glass: 22 3/8" X 14 15/16" X 1/8" (2 Pieces)
1. Turn machine OFF, unplug unit and allow it to cool before attempting to replace glass. 2. Remove all loose pieces of glass (popper units: kettle may be removed to change glass). 3. Place a bungee (or large rubber band) around the unit to help hold the corner posts in
place, then remove dome. 4. Remove all rigid glass channels from around glass to be replaced, set channels aside
for reuse. Note: The rigid channels may be wedged in the corner posts or top and bottom glass
extrusions, and must be removed before new glass can be installed.
5. Carefully remove the rest of the broken glass. 6. Apply decals (if desired) to new glass panel. 7. Slide rigid glass channels over exposed sides and bottom of new glass panel. 8. Lift motor plate just enough to allow the new glass panel to slide into the corner posts
and down into the bottom glass extrusion. 9. Carefully lower the motor plate until the top glass extrusion secures glass in place. 10. Reinstall dome, and remove bungee (popper units: reinstall kettle if removed).

Page 15

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

6 oz. Kettle Assembly (56000) ­ Agitator Assembly View

Overall Kettle 56000 Agitator Assembly 56000

1 7

1

**Apply Loctite 246 to

8

bottom of set screws before installing.

2

8 9 10

6**

5

11

12

13*

15 16, 14

14 *See Parts List note.

See Kettle Bottom Assembly.

3 4

Complete Kettle Assembly

17

18

Complete Agitator Assembly (Includes Lids)

Item

Part Description

1 8-32 TALL ACORN NUT 2 8-32 X 1/2 PHIL PAN M/S 3 DUMP HANDLE RH 4 DUMP HANDLE KNOB 5 SPACER (for Dump Handle) 6** 8-32 X 1" SET SCREW 7 LID & AGITATOR ASSY (Complete Assembly) 8 KETTLE CROSSBAR ASSEMBLY 9 FRONT LID W/FORMED LIFTER 10 REAR KETTLE LID 11 AGITATOR BEARING HUB 12 NEEDLE BEARING
SPUR GEAR KIT (Includes 2 gears with set 13* screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.) 14 SET SCREW #10-32 X 3/16 15 AGITATOR SHAFT 16 SET COLLAR 5/16 ID 5/8 OD 17 STIR ROD 18 AGITATOR WEIGHT

Part Number 56000
47702 47141 49314 47110 49362 77933 59103 59102 49017 49016 43434 47106
47059K
41742 69710 46649 69714 69715

Page 16

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

6 oz. Kettle Assembly (56000) ­ Kettle Bottom Assembly

1 Kettle Bottom Assembly

987

Kettle Bottom Assembly 49472N Element View 56000

2
5
4 3
General image shown for reference.

Lock Nut View

6

Top Lock Nut - Fastens each thermostat and

ground. Install Lock Nut

with triangle in UP

position (as shown).

ONE TIME USE ONLY,

REPLACE NUT if

removed.

Thermostat

Welded Stud

Item

Part Description

1

KETTLE BOTTOM ASSEMBLY (includes parts listed below)

2 KETTLE SHELL

3 KETTLE LEAD ASSY

4 KETTLE GASKET

5 8 OZ. KETTLE/HEATER

6 8-32 TOP LOCK NUT (always replace if removed)

7 450°F THERMOSTAT (includes two 6-32 screws)

8 THERMOSTAT SHUNT BAR

9 525°F THERMOSTAT (includes two 6-32 screws)

Part Number 56000
56000W
49431 49328 49368 56006 67943 76089 47193 76702

Page 17

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Cabinet Exterior ­ Front View

2

3

4

5

1 See Kettle Assembly Section

2085-01-000
7, 8 6
For Glass Panels, see Replacing Glass section.

9, 10 11

Model 2085 shown for parts reference.

Item

Part Description

1 FRONT GLASS DECAL

2 8-32" X 5/8" TYPE 23 HX HD

3 TOP PAN (Dome)

4 GLASS EXTRUSION (Front Glass)

5 GLASS EXTRUSION (Side glass)

6

21 5/8" GLASS CHANNEL (used on sides of glass panels)

7

15" GLASS CHANNEL (used on top and bottom of side glass panels)

8

17" GLASS CHANNEL (used on top and bottom of front glass panel)

9 GLIDE

10 10-24 X 3/4 HEX HD

11 BLACK CRUTCH TIP

Part Number

2085, 2656 2086, 1866

49158

77506

49052

49052

49452

49769

74164

74164

49508

49508

49509

49509

49510

49510

49511
47328 41314 49123

49511
47328 41314 49123

Page 18

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Cabinet Exterior ­ Rear View

2085-01-000
**Complete Door Hardware Kit

(See next page for individual component breakdown).

1

2**

3
For Labels, see Safety Label Section.
4

* CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard.

5, 6 7

8 9*

Model 2085 shown for parts reference.

Item

Part Description

1 MAGNETIC CATCH 2** COMPLETE DOOR HARDWARE KIT 3 PLEXIGLASS DOOR 4 DROP PANEL 5 KNOB LID LIFT 6 8-32" X 3/8" PH PAN W/SEMS 7 OLD MAID PAN 8 #SR-6P3-4 STRAIN RELIEF 9* POWER SUPPLY CORD

Part Number

2085, 2086, 1866

2656

47561

47561

61380

61380

49395

49395HD

49145

49145

47120

47120

42227

42227

49100

49100

76026

76026

22038

22038

Page 19

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Door Hardware Kit 61380 ­ Individual Component Breakdown

1
2 4
3 5

6

7

8

9

Complete Door Hardware Kit (P/N 61380) (contains all parts shown above)

Item

Part Description

1 KNOB LID LIFT 2 TEE BOLT 3 8-32 X 5/16 SLOTTED HEX 4 8-32 X 3/8 PH PAN W/SEMS 5 ACORN NUT #8-32 6 MALE HINGE SHORT LEFT 7 FEMALE HINGE LEFT HAND 8 FEMALE HINGE RIGHT HAND 9 MALE HINGE SHORT RIGHT

Part Number
61380
47120 75267 49594 42227 47702 41349 61359 61373 41350

Page 20

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Cabinet Interior ­ Hanger Assembly
2656
1

For Labels, see Safety Label Section.

2

3

4

5 LED Light
6
7

* See Parts List note. 12 11 9*, 10
Data Plate
8

See Kettle Assembly section for Kettle parts breakdown.

Model 2656 shown for general parts reference only.

Item

Part Description

1 SMALL SWITCH BOX 2 SWITCH BOX LABEL 3 GREEN LIGHTED ROCKER SWITCH 4 DPST ROCKER SWITCH 5 LED REPLACEMENT NO PLATE 6 POWER SUPPLY 24VDC 20W 7 REAR HANGER ARM 8 FRONT HANGER ARM
SPUR GEAR KIT (Includes 2 gears with set 9 screws. Always replace Agitator Spur Gear and
Kettle Drive Motor Gear as a set.) 10 10-32" X 3/16" SET SCREW 11 GEAR BLOCK ASSEMBLY 12 15 AMP TWIST LOCK KETTLE RECPT

Part Number All Models
48501 48502 42798 42532 100544 55394 49009 49010
47059K
41742 67194 49330

Page 21

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Cabinet Interior ­ Corn Pan/Element View
2085 Shown

1
2 3, 4 3

8

7

General image shown for parts reference only.

6

5

See Safety Label Section.

Item

Part Description

1

WIRE DUCT (runs the entire length of the corner post)

2 BOTTOM CORN PAN

3 8-32 X 3/8 SLT. HWH M/S

4 8-32 HEX M/S NUT

5 CORNER COVER

6 CORNER COVER ­ COVER

7 STRIP HEAT ELEMENT 50W

8 STRIP HEATER BRACKET

Part Number All Models
49091
49506 42044 74149 49105 49104 49440 49425

Page 22

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Dome Interior ­ Electrical Components

1 LED Light
2 2A

2656
8

Model 2656 shown for general parts reference only.

3

4

7

5

6

PowerOff Control (Available on select

models only.)

Item

Part Description

1 LED REPLACEMENT NO PLATE 2 POWER SUPPLY 24VDC 20W 2A 20W POWER SUPPLY BRACKET 3 AUTO KETTLE POWEROFF CNTRL PCB 4 BRACKET, KETTLE POWEROFF CNTRL 5 6-32 X 3/8 PHIL PAN M/S 6 #6 INTERNAL TOOTH L/W 410SS 7 15 AMP TWIST LOCK KETTLE RECPT 8 120 VOLT KETTLE DRIVE MOTOR

Part Number

2085, 2086 2656, 1866

100544

100544

55394

55394

55414

55414

55402

55427

39000

39001

49330

49330

47038

47038

Page 23

gmpopcorn.com

P-60 / Sixty Special Poppers
Safety Labels
1
Unit Labels

Model No. 2085, 2656, 2086, 1866

2
3
4
5 On units with PowerOff Control feature only.

6
Kettle Lead-In Label
7
Power Cord Label

Item

Part Description

1 UNIVERSAL POPPER DECAL 2 LABEL UNPLUG TO CLEAN 3 MAIN GROUND LABEL 4 WARNING, SURFACE CONTACT 5 LABEL POWEROFF CNTRL 6 CONDUIT WARNING LABEL 7 WARNING LABEL CORD

Accessories

Part Number

2085, 2086 2656, 1866

41019

41019

76097

76097

42375

42375

87087

87087

55436

82840

82840

68720

68720

1

2

Item

Part Description

1 STAMPED ALUMINUM SCOOP 2 MEASURE 6.5 cc 3 MEASURE 6 oz.

3
Part Number
2071 47678 49049

Page 24

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Wiring Diagram
Model No. 2085, 2086

Page 25

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

Model No. 2656, 1866

Page 26

gmpopcorn.com

P-60 / Sixty Special Poppers

Model No. 2085, 2656, 2086, 1866

WARRANTY
WARRANTY
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.'s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for "Perishable Parts" on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co.
The term "Original Purchaser" as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.

10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com

Phone: (800) 543-0862 Fax: (800) 542-1496

(513) 769-7676

(513) 769-8500

© 2017 ­ The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent.

Page 27

gmpopcorn.com


Acrobat Distiller 10.0.0 (Windows)

Search Any Device: