EMC TRF Template

eie

GSM Test Report

Benton Technology Co., Ltd L10 Tablet PC 2AZVY-L10 2AZVYL10 l10

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 46 Pages, 3.48MB

Document DEVICE REPORTGetApplicationAttachment.html?id=6421717
Page 1 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

FCC TEST REPORT FOR
Benton Technology Co., Ltd Tablet PC
Test Model: L10 Additional Model No.: D10A, P30H, B10K, M40, V30, P100A

Prepared for Address
Prepared by Address
Tel Fax Web Mail

: Benton Technology Co., Ltd : 101-501 East Block Building#1, Fuye Road No.4, Guanhu Street,
Longhua District, Shenzhen Guangdong, China.
: Shenzhen LCS Compliance Testing Laboratory Ltd. : 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park
Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China : (+86)755-82591330 : (+86)755-82591332 : www.LCS-cert.com : [email protected]

Date of receipt of test sample Number of tested samples Sample No. Serial number Date of Test Date of Report

: February 27, 2023 :2  A022023062-1, A022023062-2 : Prototype : February 27, 2023 ~ March 06, 2023 : March 07, 2023

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 2 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

FCC TEST REPORT

FCC Part 22 /Part 24

Report Reference No........................ : FCC ID.................................................. : Date of Issue.......................................:

LCSA022023062EG 2AZVY-L10 March 07, 2023

Testing Laboratory Name................: Shenzhen LCS Compliance Testing Laboratory Ltd.

Address................................................. :

101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China

Applicant's name............................... : Benton Technology Co., Ltd

Address................................................. : 101-501 East Block Building#1, Fuye Road No.4, Guanhu Street, Longhua District, Shenzhen Guangdong, China.

Test specification.............................. :

Standard................................................: FCC Part 22: Public Mobile Services FCC Part 24: Personal Communication Services
Test Report Form No ......................... : LCSEMC-1.0
TRF Originator......................................: Shenzhen LCS Compliance Testing Laboratory Ltd.
Master TRF........................................... : Dated 2011-03
Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.
Test item description........................: Tablet PC

Trade Mark............................................: PRITOM

Test Model............................................ : Ratings...................................................:
Hardware version.................................:

L10
Input: 5V 3A For AC Adapter Input: 100-240V~, 50/60Hz, 0.4A max Adapter Output: 5V 2A DC 3.8V by Rechargeable Li-ion Battery, 8000mAh
/

Software version ................................. : /

Frequency.............................................. GSM 850MHz; PCS 1900MHz

Result.....................................................: PASS

Compiled by:

Supervised by:

Approved by:

Diamond Lu/ Administrator

Cary Luo/ Technique principal

Gavin Liang/ Manager

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 3 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

TEST REPORT

Test Report No. :

LCSA022023062EG

March 07, 2023
______________________________________________________________________________________________
Date of issue

EUT........................................ : Tablet PC Test Model........................... : L10

Applicant............................... Address..................................
Telephone.............................. Fax.........................................

: Benton Technology Co., Ltd : 101-501 East Block Building#1, Fuye Road No.4, Guanhu Street,
Longhua District, Shenzhen Guangdong, China. :/ :/

Manufacturer........................ Address...................................
Telephone.............................. Fax.........................................

: Benton Technology Co., Ltd : 101-501 East Block Building#1, Fuye Road No.4, Guanhu Street,
Longhua District, Shenzhen Guangdong, China.
:/
:/

Factory.................................. Address..................................
Telephone.............................. Fax.........................................

: Benton Technology Co., Ltd : 101-501 East Block Building#1, Fuye Road No.4, Guanhu Street,
Longhua District, Shenzhen Guangdong, China. :/ :/

Test Result:

PASS

The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 4 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Report Version 000

Revison History

Issue Date March 07, 2023

Revision Content Initial Issue

Revised By ---

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 5 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Contents

1

T E S T S T A N D A R D S ....................................................................................................................... 6

2

S U M M A R Y ........................................................................................................................................... 7

2.1

Product Description

7

2.2

Equipment under Test

9

2.3

Short description of the Equipment under Test (EUT)

10

2.4

Internal Identification of AE used during the test

10

2.5

Normal Accessory setting

10

2.6

Test Sample

10

2.7

EUT configuration

10

2.8

Related Submittal(s) / Grant (s)

10

2.9

Modifications

10

2.10 General Test Conditions/Configurations

11

3

T E S T E N V I R O N M E N T ............................................................................................................... 1 2

3.1

Address of the test laboratory

12

3.2

Test Facility

12

3.3

Environmental conditions

12

3.4

Test Description

13

3.5

Equipments Used during the Test

14

3.6

Measurement uncertainty

15

4

T E S T C O N D I T I O N S A N D R E S U L T S ................................................................................ 1 6

4.1

Output Power

16

4.2

Radiated Spurious Emssion

20

4.3

Occupied Bandwidth and Emission Bandwidth

24

4.4

Band Edge Complicance

27

4.5

Spurious Emission on Antenna Port

30

4.6

Frequency Stability Test

40

4.7

Peak-to-Average Ratio (PAR)

43

5

T E S T S E T U P P H O T O G R A P H S O F E U T .........................................................................4 6

6

E X T E R I O R P H O T O G R A P H S O F T H E E U T ...................................................................4 6

7

I N T E R I O R P H O T O G R A P H S O F T H E E U T .................................................................... 4 6

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 6 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

1 TEST STANDARDS
The tests were performed according to following standards:
FCC Part 22 (10-1-16 Edition): Cellular Radiotelephone Service. FCC Part 24(10-1-16 Edition): Broadband PCS. ANSI/TIA-603-E-2016: Land Mobile FM or PM Communications Equipment Measurement and Performance Standards. 47 CFR FCC Part 15 Subpart B: Unintentional Radiators. FCC Part 2: Frequency Allocations And Radio Treaty Matters: General Rules And Regulations. ANSI C63.4:2014: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. ANSI C63.26-2015: Compliance Testing of Transmitters Used in Licensed Radio Services. FCC KDB971168 D01 Power Meas License Digital Systems v03r01.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 7 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

2 SUMMARY

2.1 Product Description

The Benton Technology Co., Ltd's Model: L10 or the "EUT" as referred to in this report; more general information as follows, for more details, refer to the user's manual of the EUT.

EUT

: Tablet PC

Test Model

: L10

Additional Model No. : D10A, P30H, B10K, M40, V30, P100A

Model Declaration Power Supply
Hardware Version

: PCB board, structure and internal of these model(s) are the same, So no additional models were tested
: Input: 5V 3A For AC Adapter Input: 100-240V~, 50/60Hz, 0.4A max
Adapter Output: 5V 2A DC 3.8V by Rechargeable Li-ion Battery, 8000mAh :/

Software Version

:/

Bluetooth

:

Frequency Range

: 2402MHz~2480MHz

Channel Number Channel Spacing Modulation Type Bluetooth Version

: 79 channels for Bluetooth V5.0 (DSS) 40 channels for Bluetooth V5.0 (DTS)
: 1MHz for Bluetooth V5.0 (DSS) 2MHz for Bluetooth V5.0 (DTS)
: GFSK, /4-DQPSK, 8-DPSK for Bluetooth V5.0(DSS) GFSK for Bluetooth V5.0 (DTS)
: V5.0

Antenna Description : PIFA Antenna, 2.17dBi(Max.)

WIFI(2.4G Band)

:

Frequency Range

: 2412MHz~2462MHz

Channel Spacing

: 5MHz

Channel Number Modulation Type
Antenna Description

: 11 Channels for 20MHz bandwidth (2412~2462MHz) 7 Channels for 40MHz bandwidth (2422~2452MHz)
: IEEE 802.11b: DSSS (CCK, DQPSK, DBPSK) IEEE 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11n: OFDM (64QAM, 16QAM, QPSK, BPSK)
: PIFA Antenna, 2.17dBi(Max.)

5.2G WLAN

:

Frequency Range

: 5180MHz~5240MHz

Channel Number Modulation Type Antenna Description

: 4 channels for 20MHz bandwidth(5180MHz~5240MHz) 2 channels for 40MHz bandwidth(5190MHz~5230MHz) 1 channels for 80MHz bandwidth(5210MHz)
: IEEE 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11n: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11ac: OFDM (256QAM, 64QAM, 16QAM, QPSK, BPSK)
: PIFA Antenna, 1.96dBi(Max.)

5.8G WLAN

:

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 8 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Frequency Range Channel Number
Modulation Type
Antenna Description 2G Support Band Release Version GPRS Class EGPRS Class Type Of Modulation Antenna Description
3G Support Band
Release Version Type Of Modulation Antenna Description LTE Support Band
LTE Release Version Type Of Modulation Antenna Description
Power Class GPS function

: 5745MHz~5825MHz

: 5 channels for 20MHz bandwidth(5745MHz~5825MHz) 2 channels for 40MHz bandwidth(5755MHz~5795MHz) 1 channels for 80MHz bandwidth(5775MHz)
: IEEE 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11n: OFDM (64QAM, 16QAM, QPSK, BPSK) IEEE 802.11ac: OFDM (256QAM, 64QAM, 16QAM, QPSK, BPSK)
: PIFA Antenna, 2.81dBi(Max.)

:

: GSM 900 (EU-Band) GSM 850 (U.S.-Band)
: R99

DCS 1800 (EU-Band) PCS 1900 (U.S.-Band)

: Class 12

: Class 12

: GMSK for GSM/GPRS; GMSK/8PSK for EGPRS

: PIFA Antenna 0.7dBi (max.) For GSM 850 0.5dBi (max.) For PCS 1900
:

: WCDMA Band II (U.S.-Band) WCDMA Band V (U.S.-Band) WCDMA Band IV (U.S.-Band) WCDMA Band I (EU-Band) WCDMA Band VIII (EU-Band)
: R8

: QPSK, 16QAM

: PIFA Antenna 0.7dBi (max.) For WCDMA Band V
:

: E-UTRA Band 1(Non U.S.-Band) E-UTRA Band 3(Non U.S.-Band) E-UTRA Band 5(U.S.-Band) E-UTRA Band 7(U.S.-Band) E-UTRA Band 8(Non U.S.-Band) E-UTRA Band 20(Non U.S.-Band) E-UTRA Band 38(U.S.-Band) E-UTRA Band 40(Non U.S.-Band) E-UTRA Band 41(U.S.-Band)
: R8

: QPSK/16QAM

: PIFA Antenna 0.7dBi (max.) For E-UTRA Band 5 1.3dBi (max.) For E-UTRA Band 7 1.3dBi (max.) For E-UTRA Band 38 1.3dBi (max.) For E-UTRA Band 41
: Class 3

: Support and only RX

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 9 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

FM function
Extreme temp. Tolerance Extreme vol. Limits

: Support and only RX : -30°C to +50°C : 3.4VDC to 4.2VDC (nominal: 3.8VDC)

2.2 Equipment under Test
Power supply system utilised
Power supply voltage

:  120V / 60 Hz

 115V / 60Hz

 12 V DC

 24 V DC

 Other (specified in blank below) 3.8V DC

Test frequency list Test Mode GSM850 Test Mode PCS1900

TX/RX TX RX
TX/RX TX RX

Low(L) Channel 128 824.2 MHz Channel 128 869.2 MHz
Low(L) Channel 512 1850.2 MHz Channel 512 1930.2 MHz

RF Channel Middle (M) Channel 190 836.6 MHz Channel 190 881.6 MHz RF Channel Middle (M) Channel 661 1880.0 MHz Channel 661 1960.0 MHz

High (H) Channel 251 848.8 MHz Channel 251 893.8 MHz
High (H) Channel 810 1909.8 MHz Channel 810 1989.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 10 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

2.3 Short description of the Equipment under Test (EUT) 2.3.1 General Description

L10 is subscriber equipment in the BT/BLE/2.4GWIFI/5.2GWIFI/5.8GWIFI/GSM/WCDMA/LTE/GPS/FM system. GSM/GPRS/EGPRS frequency band is Band II//V. The HSPA/UMTS frequency band is Band V. LTE frequency band is band 5/7/38/41.The HSPA/UMTS frequency Band V test data included in this report. The L10 implements such functions as RF signal receiving/transmitting, GSM/GPRS/EGPRS/ HSPA/UMTS/LTE protocol processing, video MMS service and etc. Externally it provides SIM card interface.

2.4 Internal Identification of AE used during the test

AE ID* AE1 AE2

Description Rechargeable Li-Polymer Battery Switching Adapter

AE2 Adapter Model: FX2U-050200U For AC Adapter Input: 100-240V~, 50/60Hz, 0.4A max
Adapter Output: 5V 2A

2.5 Normal Accessory setting

Fully charged battery was used during the test.

2.6 Test Sample

The application provides 2 samples to meet requirement;

Sample Number

Description

Sample 1(A022023062-1)

Engineer sample ­ continuous transmit

Sample 2(A022023062-2)

Normal sample ­ Intermittent transmit

2.7 EUT configuration
The following peripheral devices and interface cables were connected during the measurement:

 - supplied by the manufacturer

 - supplied by the lab

 Power Cable  Multimeter

Length (m) : /

Shield :

/

Detachable : /

Manufacturer : /

Model No. :

/

2.8 Related Submittal(s) / Grant (s)
This submittal(s) (test report) is intended for FCC ID: 2AZVY-L10 filing to comply with FCC Part 22 and Part 24 Rules.

2.9 Modifications
No modifications were implemented to meet testing criteria.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 11 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

2.10 General Test Conditions/Configurations 2.10.1 Test Modes

NOTE: The test mode(s) are selected according to relevant radio technology specifications.

Test Mode GSM/TM1 GSM/TM2 GSM/TM3

Test Modes Description GSM system, GSM, GMSK modulation GSM system, GPRS, GMSK modulation GSM system, EDGE, GMSK, 8PSK modulation

Note: 1. As GSM and GPRS with the same emission designator, test result recorded in this report at the worst case
GSM/TM1 only after exploratory scan.

2.10.2 Test Environment

Environment Parameter Relative Humidity Temperature
Voltage

Selected Values During Tests

Ambient

TN

Ambient

VL

DC 3.4V

VN

DC 3.8V

VH

DC 4.2V

NOTE: VL=lower extreme test voltage VN=nominal voltage VH=upper extreme test voltage TN=normal temperature

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 12 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

3 TEST ENVIRONMENT
3.1 Address of the test laboratory
Shenzhen LCS Compliance Testing Laboratory Ltd
101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China The sites are constructed in conformance with the requirements of ANSI C63.4 (2014) and CISPR Publication 22.
3.2 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
NVLAP Accreditation Code is 600167-0. FCC Designation Number is CN5024. CAB identifier is CN0071. CNAS Registration Number is L4595. Test Firm Registration Number: 254912

3.3 Environmental conditions
During the measurement the environmental conditions were within the listed ranges:

Temperature:

15-35 ° C

Humidity:

30-60 %

Atmospheric pressure:

950-1050mbar

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 13 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

3.4 Test Description 3.4.1 Cellular Band (824-849MHz paired with 869-894MHz)

Test Item

FCC Rule No.

Requirements

Verdict

Effective(Isotropic) Radiated Output Power

§2.1046, §22.913

FCC: ERP  7W.

Pass

Modulation Characteristics

§2.1047

Digital modulation

N/A

Bandwidth

§2.1049

OBW: No limit. EBW: No limit.

Pass

Band Edges Compliance

§2.1051, §22.917

-13dBm/1%*EBW, in 1MHz bands immediately outside and adjacent to
The frequency block.

Pass

Spurious Emission at Antenna Terminals

§2.1051, §22.917

 -13dBm/100kHz, from 9kHz to 10th harmonics but outside authorized operating frequency ranges.

Pass

Field Strength of Spurious Radiation

§2.1053, §22.917

 -13dBm/100kHz.

Pass

Frequency Stability

§2.1055, §22.355

 ±2.5ppm.

Pass

Peak-Average Ratio

§22.913

FCC:Limit13dB

N/A

Receiver Spurious Emissions

N/A

--

Pass

NOTE 1: For the verdict, the "N/A" denotes "not applicable", the "N/T" de notes "not tested".

3.4.2 PCS Band (1850-1910MHz paired with 1930-1990MHz)

Test Item

FCC Rule No.

Requirements

Verdict

Effective(Isotropic) Radiated Output Power

§2.1046, §24.232

EIRP  2W

Pass

Peak-Average Ratio

§2.1046, §24.232

13dB

Pass

Modulation Characteristics

§2.1047

Digital modulation

N/A

Bandwidth

§2.1049

OBW: No limit. EBW: No limit.

Pass

Band Edges Compliance

§2.1051, §24.238

 -13dBm/1%*EBW, In 1MHz bands immediately outside and adjacent to The frequency block.

Pass

Spurious Emission at Antenna Terminals

§2.1051, §24.238

-13dBm/1MHz, from 9kHz to10th harmonics but outside authorized Operating frequency ranges.

Pass

Field Strength of Spurious Radiation

§2.1053, §24.238

 -13dBm/1MHz.

Pass

Frequency Stability

§2.1055, §24.235

 ±2.5ppm.

Pass

Peak-Average Ratio

§24.232

FCC:Limit13dB

Pass

Receiver Spurious Emissions

N/A

--

Pass

NOTE 1: For the verdict, the "N/A" denotes "not applicable", the "N/T" de notes "not tested".

Remark: The measurement uncertainty is not included in the test result.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 14 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

3.5
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Equipments Used during the Test

Equipment Power Meter Power Sensor Power Sensor LTE Test Software RF Control Unit MXA Signal Analyzer WIDEBAND RADIO COMMUNICATION TESTER DC Power Supply EMI Test Software 3m Semi Anechoic Chamber Positioning Controller

Manufacturer R&S R&S R&S
Tonscend Tonscend
Agilent
R&S
Agilent AUDIX SIDT FRANKONIA Max-Full

Active Loop Antenna

SCHWARZBECK

By-log Antenna

SCHWARZBECK

Horn Antenna

SCHWARZBECK

Broadband Horn Antenna Broadband Preamplifier
EMI Test Receiver RS SPECTRUM ANALYZER

SCHWARZBECK SCHWARZBECK
R&S R&S

Broadband Preamplifier

/

6dB Attenuator
3dB Attenuator Temperature & Humidity
Chamber EMI Test Software RADIO COMMUNICATION
TESTER

/
/ GUANGZHOU
GOGNWEN Farad
R&S

Model No. NRVS
NRV-Z81 NRV-Z32 JS1120-1 JS0806-1 N9020A
CMW 500
E3642A E3
SAC-3M MF7802BS
FMZB 1519B VULB9163 BBHA 9120D BBHA 9170 BBV9719 ESR 7 FSP40
BP01M18G 100W/6dB 2N-3dB
GDS-100
EZ
CMU 200

Serial No. 100444 100458 10057 N/A
158060009 MY51250905
103818 N/A /
03CH03-HY MF780208586
00005 9163-470 9120D-1925
791 9719-025 101181 100503 P190501 1172040
/ 70932
/ 105988

Cal Date 2022-06-16 2022-06-16 2022-06-16
N/A 2022-10-29 2022-10-29 2022-06-16 2022-10-29
N/A 2022-06-16
N/A 2021-08-29 2021-09-12 2021-09-05 2021-08-29 2022-06-16 2022-06-16 2022-10-29 2022-06-16 2022-06-16 2022-10-29 2022-10-06
N/A 2022-11-15

Due Date 2023-06-15 2023-06-15 2023-06-15
N/A 2023-10-28 2023-10-28 2023-06-15 2023-10-28
N/A 2023-06-15
N/A 2024-08-28 2024-09-11 2024-09-04 2024-08-28 2023-06-15 2023-06-15 2023-10-28 2023-06-15 2023-06-15 2023-10-28 2023-10-05
N/A 2023-11-14

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 15 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

3.6 Measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to ETSI TR 100 028 " Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics" and is documented in the Shenzhen LCS Compliance Testing Laboratory Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device.

Hereafter the best measurement capability for Shenzhen LCS Compliance Testing Laboratory Ltd. is reported:

Test
Radiated Emission Radiated Emission Radiated Emission Conducted Disturbance Conducted Power Spurious RF Conducted Emission Band Edge Compliance of RF Emission Occuiped Bandwidth

Range
30~1000MHz 1~18GHz 18-40GHz
0.15~30MHz 9KHz~18GHz 9KHz~40GHz 9KHz~40GHz 9KHz~40GHz

Measurement Uncertainty
3.10 dB 3.80 dB 3.90 dB 1.63 dB 0.61 dB 1.22 dB 1.22 dB
-

Notes
(1) (1) (1) (1) (1) (1) (1) (1)

This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=1.96.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 16 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4 TEST CONDITIONS AND RESULTS
4.1 Output Power
TEST APPLICABLE
During the process of testing, the EUT was controlled via R&S Digital Radio Communication tester (CMU200) to ensure max power transmission and proper modulation. This result contains output power and EIRP measurements for the EUT. In all cases, output power is within the specified limits.
4.1.1 Conducted Output Power
TEST CONFIGURATION

TEST PROCEDURE

Conducted Power Measurement: a) Place the EUT on a bench and set it in transmitting mode. b) Connect a low loss RF cable from the antenna port to a CMU200 by an Att. c) EUT Communicate with CMU200 then selects a channel for testing. d) Add a correction factor to the display CMU200, and then test.

TEST RESULTS

GSM 850

GPRS (GMSK)
EDGE (8PSK)

GSM

1TX slot 2TX slot 3TX slot 4TX slot 1TX slot 2TX slot 3TX slot 4TX slot

Burst Average Conducted power (dBm)

Channel/Frequency(MHz)

128/824.2

190/836.6

251/848.8

32.69

32.69

32.66

32.52

32.56

32.49

30.96

30.97

30.93

29.49

29.53

29.48

27.96

27.99

27.99

26.00

25.97

25.98

24.47

24.52

24.46

23.01

23.01

22.95

21.50

21.48

21.47

PCS 1900

GPRS (GMSK)
EDGE (8PSK)

GSM

1TX slot 2TX slot 3TX slot 4TX slot 1TX slot 2TX slot
3TX slot
4TX slot

Burst Average Conducted power (dBm)

Channel/Frequency(MHz)

512/1850.2

661/1880

810/1909.8

29.67

29.67

29.67

29.49 27.96 26.48 24.95

29.54 27.98 26.48 24.97

29.52 27.95 26.45 24.93

25.49

25.49

25.47

23.95

24.00

23.95

22.45

22.48

22.46

20.98

21.00

20.94

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 17 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.1.2 Radiated Output Power
TEST DESCRIPTION
This is the test for the maximum radiated power from the EUT. Per rule Part 24.232(c) specifies, "Mobile/portable stations are limited to 2 watts e.i.r.p. Peak power" and 24.232(e) specifies that "Peak transmit power must be measured over any interval of continuous transmission using instrumentation calibrated in terms of an rms-equivalent voltage." Per rule Part 22.913(a) specifies " The ERP of mobile transmitters and auxiliary test transmitters must not exceed 7 Watts."
TEST CONFIGURATION

TEST PROCEDURE
1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission measurements. The height of receiving antenna is 1.50 m. Detected emissions were maximized at each frequency by rotating the EUT through 360° and adjusting the receiving antenna polarization. The radiated emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured with peak detector.
2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver.
3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set Test Receiver or Spectrum RBW=1MHz,VBW=3MHz, And the maximum value of the receiver should be recorded as (Pr).
4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 18 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization. 5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the Amplifier Gain (PAg) should be recorded after test. The measurement results are obtained as described below: Power(EIRP)=PMea+ PAg - Pcl + Ga 6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and known input power. 7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi.

TEST LIMIT

According to 22.913(a), 24.232(c) , the ERP should be not exceed following table limits:

GSM850(GPRS850,EDGE850)

Function

Power Step

Burst Peak ERP (dBm)

GSM

5

FCC: 38.45dBm (7W)

GPRS

3

FCC: 38.45dBm (7W)

EDGE

8

FCC: 38.45dBm (7W)

Function GSM GPRS EDGE

PCS1900(GPRS1900,EDGE1900) Power Step 0 3 2

Burst Peak EIRP (dBm) 33.01dBm (2W) 33.01dBm (2W) 33.01dBm (2W)

TEST RESULTS

Remark: 1. We were tested all Configuration refer 3GPP TS151 010. 2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi) 3. ERP = EIRP ­ 2.15dBi as EIRP by subtracting the gain of the dipole. 4. Margin = Emission Level - Limit 5. We tested the worst-case records for H and V directions, and only the worst-case records for V direction
were recorded in the report.

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 19 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

GSM/TM1/GSM850

Frequency PMea (MHz) (dBm)

824.20 836.60 848.80

-7.04 -6.95 -7.06

Pcl (dB)

Ga Antenna Gain(dB)

Correction (dB)

3.45

8.45

2.15

3.49

8.45

2.15

3.55

8.36

2.15

PAg (dB)
33.79 33.85 33.88

Burst Average
ERP (dBm)
29.60 29.71 29.48

Limit (dBm)
38.45 38.45 38.45

Margin (dB)

Polarization

-8.85

V

-8.74

V

-8.97

V

GSM/TM3/EDGE850

Frequency PMea (MHz) (dBm)

824.20 836.60 848.80

-12.08 -12.07 -12.03

Pcl (dB)

Ga Antenna Gain(dB)

Correction (dB)

3.45

8.45

2.15

3.49

8.45

2.15

3.55

8.36

2.15

PAg (dB)
33.79 33.85 33.88

Burst Average
ERP (dBm)
24.56 24.59 24.51

Limit (dBm)
38.45 38.45 38.45

Margin (dB)

Polarization

-13.89

V

-13.86

V

-13.94

V

GSM/TM1/PCS1900

Frequency (MHz)

PMea (dBm)

1850.20 1880.00 1909.80

-12.01 -11.97 -11.92

Pcl (dB)

Ga Antenna Gain(dB)

PAg (dB)

4.03

8.38

35.51

4.08

8.33

35.56

4.14

8.26

35.63

Burst Average
EIRP (dBm)
27.85 27.84 27.83

Limit (dBm)
33.01 33.01 33.01

Margin (dB)
-5.16 -5.17 -5.18

Polarization
V V V

GSM/TM3/EDGE1900

Frequency (MHz)

PMea (dBm)

1850.20 1880.00 1909.80

-17.03 -17.00 -16.97

Pcl (dB)

Ga Antenna Gain(dB)

PAg (dB)

Burst Average
EIRP (dBm)

Limit (dBm)

Margin (dB)

Polarization

4.03

8.38

35.51

22.83

33.01

-10.18

V

4.08

8.33

35.56

22.81

33.01

-10.20

V

4.14

8.26

35.63

22.78

33.01

-10.23

V

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 20 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.2 Radiated Spurious Emssion
TEST APPLICABLE
According to the TIA/EIA 603D:2010 and FCC Part 2.1033 test method, The Receiver or Spectrum was scanned from lowest frequency frequency generated within the equipment to the 10th harmonic of the highest frequency generated within the equipment, which is the transmitted carrier that can be as high as 1910 MHz. The resolution bandwidth is set as outlined in Part 24.238, Part 22.917, RSS-132 §5.5 and RSS-133 §6.5. The spectrum is scanned with the mobile station transmitting at carrier frequencies that pertain to low, mid and high channels of PCS1900 and GSM850.
TEST CONFIGURATION

TEST PROCEDURE
1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission measurements. The height of receiving antenna is 1.50 m. Detected emissions were maximized at each frequency by rotating the EUT through 360° and adjusting the receiving antenna polarization. The radiated emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured with peak detector.
2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT. The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading of the spectrum analyzer or receiver.
3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set Test Receiver or Spectrum RBW=1MHz,VBW=3MHz, And the maximum value of the receiver should be recorded as (Pr).
4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the frequency band of interest is connected to the substitution antenna with a cable that has been constructed to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the substitution antenna, and adjust the level of the signal generator output until the value of the receiver reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be performed by rotating the test item and adjusting the receiving antenna polarization.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 21 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

5. A amplifier should be connected to the Signal Source output port. And the cable should be connect between

the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain (Ga) and the

Amplifier Gain (PAg) should be recorded after test.

The measurement results are obtained as described below:

Power(EIRP)=PMea+ PAg - Pcl + Ga

6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and

known input power.

7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.

8. In order to make sure test results more clearly,we set frequency range and sweep time for difference

frequency range as follows table:

Working Frequency

Subrange (GHz)

RBW

VBW

Sweep time (s)

0.00009~0.15

1KHz

3KHz

30

0.00015~0.03

10KHz

30KHz

10

0.03~1

100KHz

300KHz

10

TM1/GSM 850

1~2

1 MHz

3 MHz

2

2~5

1 MHz

3 MHz

3

5~8

1 MHz

3 MHz

3

8~10

1 MHz

3 MHz

3

0.00009~0.15

1KHz

3KHz

30

0.00015~0.03

10KHz

30KHz

10

0.03~1

100KHz

300KHz

10

1~2

1 MHz

3 MHz

2

TM1/PCS 1900

2~5 5~8

1 MHz 1 MHz

3 MHz 3 MHz

3 3

8~11

1 MHz

3 MHz

3

11~14

1 MHz

3 MHz

3

14~18

1 MHz

3 MHz

3

18~20

1 MHz

3 MHz

2

TEST LIMITS

According to 24.238 and 22.917 specify that the power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log (P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0 dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the specification from relative to absolute terms is carried out.

Frequency TM1/GSM 850
TM1/PCS 1900

Channel Low
Middle High Low Middle High

Frequency Range 9KHz -10GHz 9KHz -10GHz 9KHz -10GHz 9KHz -20GHz 9KHz -20GHz 9KHz -20GHz

Verdict PASS PASS PASS PASS PASS PASS

TEST RESULTS

Remark: 1. We were tested all refer 3GPP TS151 010. 2. EIRP=PMea(dBm)-Pcl(dB) +Ga(dBi) 3. We were not recorded other points as values lower than limits. 4. Margin = EIRP - Limit

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 22 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

GSM/TM1/GSM850_ Low Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

1648.40 -43.43

3.86

2472.60 -44.22

4.29

1648.40 -39.75

3.86

2472.60 -41.66

4.29

Diatance
3.00 3.00 3.00 3.00

Ga Antenna Gain(dB)
8.56 6.98 8.56 6.98

GSM/TM1/GSM850_ Middle Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

1673.20 -42.10

3.9

3.00

2509.80 -46.55

4.32

3.00

1673.20 -37.51

3.9

3.00

2509.80 -43.05

4.32

3.00

Ga Antenna Gain(dB)
8.58 6.8 8.58 6.8

GSM/TM1/GSM850_ High Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

1697.60 -46.84

3.91

3.00

2546.40 -49.80

4.32

3.00

1697.60 -43.54

3.91

3.00

2546.40 -44.78

4.32

3.00

Ga Antenna Gain(dB)
9.06 6.65 9.06 6.65

GSM/TM3/EDGE850_ Low Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

1648.40 -45.26

3.86

3.00

2472.60 -46.29

4.29

3.00

1648.40 -41.66

3.86

3.00

2472.60 -44.22

4.29

3.00

Ga Antenna Gain(dB)
8.56 6.98 8.56 6.98

GSM/TM3/EDGE850_ Middle Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

1673.20 -43.99

3.9

3.00

2509.80 -48.43

4.32

3.00

1673.20 -39.31

3.9

3.00

2509.80 -45.07

4.32

3.00

Ga Antenna Gain(dB)
8.58 6.8 8.58 6.8

GSM/TM3/EDGE850_ High Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

1697.60 -49.04

3.91

3.00

2546.40 -51.75

4.32

3.00

1697.60 -45.31

3.91

3.00

2546.40 -47.08

4.32

3.00

Ga Antenna Gain(dB)
9.06 6.65 9.06 6.65

Peak EIRP (dBm) -38.73 -41.53 -35.05 -38.97
Peak EIRP (dBm) -37.42 -44.07 -32.83 -40.57
Peak EIRP (dBm) -41.69 -47.47 -38.39 -42.45
Peak EIRP (dBm) -40.56 -43.60 -36.96 -41.53
Peak EIRP (dBm) -39.31 -45.95 -34.63 -42.59
Peak EIRP (dBm) -43.89 -49.42 -40.16 -44.75

Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00

Margin (dB)
-25.73 -28.53 -22.05 -25.97

Polarization
H H V V

Margin (dB)
-24.42 -31.07 -19.83 -27.57

Polarization
H H V V

Margin (dB)
-28.69 -34.47 -25.39 -29.45

Polarization
H H V V

Margin (dB)
-27.56 -30.60 -23.96 -28.53

Polarization
H H V V

Margin (dB)
-26.31 -32.95 -21.63 -29.59

Polarization
H H V V

Margin (dB)
-30.89 -36.42 -27.16 -31.75

Polarization
H H V V

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 23 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

GSM/TM1/PCS1900_ Low Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3700.40 -45.46

5.26

3.00

5550.60 -46.37

6.11

3.00

3700.40 -41.42

5.26

3.00

5550.60 -43.82

6.11

3.00

Ga Antenna Gain(dB)
9.88 11.36 9.88 11.36

GSM/TM1/PCS1900_ Middle Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3760.00 -44.16

5.32

3.00

5640.00 -48.15

6.19

3.00

3760.00 -39.58

5.32

3.00

5640.00 -44.66

6.19

3.00

Ga Antenna Gain(dB)
10.03 11.41 10.03 11.41

GSM/TM1/PCS1900_ High Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3819.60 -49.23

5.36

3.00

5729.40 -51.66

6.24

3.00

3819.60 -45.12

5.36

3.00

5729.40 -47.31

6.24

3.00

Ga Antenna Gain(dB)
9.62 11.46 9.62 11.46

GSM/TM3/EDGE1900_ Low Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3700.40 -46.92

5.26

3.00

5550.60 -48.04

6.11

3.00

3700.40 -43.75

5.26

3.00

5550.60 -46.27

6.11

3.00

Ga Antenna Gain(dB)
9.88 11.36 9.88 11.36

GSM/TM3/EDGE1900_ Middle Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3760.00 -46.04

5.32

3.00

5640.00 -50.60

6.19

3.00

3760.00 -41.49

5.32

3.00

5640.00 -47.39

6.19

3.00

Ga Antenna Gain(dB)
10.03 11.41 10.03 11.41

GSM/TM3/EDGE1900_ High Channel

Frequency (MHz)

PMea (dBm)

Pcl (dB)

Diatance

3819.60 -50.86

5.36

3.00

5729.40 -53.28

6.24

3.00

3819.60 -47.55

5.36

3.00

5729.40 -49.35

6.24

3.00

Ga Antenna Gain(dB)
9.62 11.46 9.62 11.46

Peak EIRP (dBm) -40.84 -41.12 -36.80 -38.57
Peak EIRP (dBm) -39.45 -42.93 -34.87 -39.44
Peak EIRP (dBm) -44.97 -46.44 -40.86 -42.09
Peak EIRP (dBm) -42.30 -42.79 -39.13 -41.02
Peak EIRP (dBm) -41.33 -45.38 -36.78 -42.17
Peak EIRP (dBm) -46.60 -48.06 -43.29 -44.13

Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00
Limit (dBm) -13.00 -13.00 -13.00 -13.00

Margin (dB)
-27.84 -28.12 -23.80 -25.57

Polarization
H H V V

Margin (dB)
-26.45 -29.93 -21.87 -26.44

Polarization
H H V V

Margin (dB)
-31.97 -33.44 -27.86 -29.09

Polarization
H H V V

Margin (dB)
-29.30 -29.79 -26.13 -28.02

Polarization
H H V V

Margin (dB)
-28.33 -32.38 -23.78 -29.17

Polarization
H H V V

Margin (dB)
-33.60 -35.06 -30.29 -31.13

Polarization
H H V V

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 24 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.3 Occupied Bandwidth and Emission Bandwidth
TEST APPLICABLE
Similar to conducted emissions; occupied bandwidth measurements are only provided for selected frequencies in order to reduce the amount of submitted data. Data were taken at the extreme and mid frequencies of PCS1900 band and GSM850 band. The table below lists the measured 99% Bandwidth and -26dBc Bandwidth.
TEST CONFIGURATION

TEST PROCEDURE

1. The EUT was set up for the max output power with pseudo random data modulation; 2. The Occupied bandwidth and Emission Bandwidth were measured with Spectrum AnalyzerN9020A; 3. Set RBW=5.1KHz,VBW=15KHz,Span=1MHz,SWT=Auto; 4. Set SPA Max hold and View, Set 99% Occupied Bandwidth/ Set -26dBc Occupied Bandwidth 5. These measurements were done at 3 frequencies, 1850.20 MHz, 1880.00 MHz and 1909.80 MHz for
PCS1900 band; 824.20MHz, 836.60 MHz and 848.80 MHz for GSM850 band. (Low, middle and high of operational frequency range).

TEST RESULTS

Test Mode
GSM/TM1 /GSM850
GSM/TM3 /EDGE850
GSM/TM1 /PCS1900
GSM/TM3 /EDGE1900

Channel
128 190 251 128 190 251 512 661 810 512 661 810

Frequency (MHz)
824.2 836.6 848.8 824.2 836.6 848.8 1850.2 1880.0 1909.8 1850.2 1880.0 1909.8

Occupied Bandwidth (99% BW)
(KHz) 242.35 241.20 241.99 250.66 247.01 242.40 242.43 243.65 243.99 251.45 245.88 249.03

Emission Bandwidth (-26 dBc BW)
(KHz) 299.1 302.6 307.9 302.5 312.2 310.3 301.0 298.9 307.8 306.7 305.5 315.6

Verdict
PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS

Remark: 1. Test results including cable loss; 2. Please refer to following plots;

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 25 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Occupied Bandwidth and Emission Bandwidth

GSM/TM1/GSM850

GSM/TM3/EDGE850

Channel 128 / 824.2 MHz

Channel 128 / 824.2 MHz

Channel 190 / 836.6 MHz

Channel 190 / 836.6 MHz

Channel 251 / 848.8 MHz

Channel 251 / 848.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 26 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Occupied Bandwidth and Emission Bandwidth

GSM/TM1/PCS1900

GSM/TM3/ EDGE1900

Channel 512 / 1850.2 MHz

Channel 512 / 1850.2 MHz

Channel 661 / 1880.0MHz

Channel 661 / 1880.0MHz

Channel 810 / 1909.8 MHz

Channel 810 / 1909.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 27 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.4 Band Edge Complicance
TEST APPLICABLE During the process of testing, the EUT was controlled via Digital Radio Communication tester (CMU200) to ensure max power transmission and proper modulation. TEST CONFIGURATION

TEST PROCEDURE

1. The EUT was set up for the max output power with pseudo random data modulation; 2. The power was measured with Spectrum Analyzer N9020A; 3. Set RBW=5.1KHz,VBW=15KHz,Span=2MHz,SWT=Auto, Dector: RMS; 1. These measurements were done at 2 frequencies, 1850.20 MHz and 1909.80 MHz for PCS1900 band;
824.20 MHz and 848.80 MHz for GSM850 band. (bottom and top of operational frequency range).

TEST RESULTS

Test Mode
GSM/TM1/GSM850 GSM/TM3/EDGE850 GSM/TM1/PCS1900 GSM/TM3/EDGE1900

Channel
128 251 128 251 512 810 512 810

Frequency (MHz)
824.2 848.8 824.2 848.8 1850.2 1909.8 1850.2 1909.8

Band Edg Compliance
(dBm) <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm

Limits (dBm)
-13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm

Verdict
PASS PASS PASS PASS

Remark: 1. Test results including cable loss; 2. Please refer to following plots;

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 28 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Band-edge Compliance

GSM/TM1/GSM850

GSM/TM3/EDGE850

Channel 128 / 824.2 MHz

Channel 128 / 824.2 MHz

Channel 251 / 848.8 MHz

Channel 251 / 848.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 29 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Band-edge Compliance

GSM/TM1/PCS1900

GSM/TM3/EDGE1900

Channel 512 / 1850.2 MHz

Channel 512 / 1850.2 MHz

Channel 810 / 1909.8 MHz

Channel 810 / 1909.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 30 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.5 Spurious Emission on Antenna Port
TEST APPLICABLE
The following steps outline the procedure used to measure the conducted emissions from the EUT. 1. Determine frequency range for measurements: From CFR 2.1057 and RSS-GEN the spectrum should be
investigated from the lowest radio frequency generated in the equipment up to at least the 10th harmonic of the carrier frequency. For the equipment of PCS1900 band, this equates to a frequency range of 9 KHz to 20 GHz, data taken from 30 MHz to 20 GHz. For GSM850, this equates to a frequency range of 9 KHz to 9 GHz,data taken from 30 MHz to 9 GHz. 2. The sweep time is set automatically by instrument itself. That should be the optimal sweep time for the span and the RBW. If the sweep time is too short, that is sweep is too fast, the sweep result is not accurate; if the sweep time is too long, that is sweep is too low, some frequency components may be lost. The instrument will give an optimal sweep time according the selected span and RBW. 3. The procedure to get the conducted spurious emission is as follows: The trace mode is set to MaxHold to get the highest signal at each frequency; Wait 25 seconds; Get the result. 4. Determine EUT transmit frequencies: below outlines the band edge frequencies pertinent to conducted emissions testing.
TEST CONFIGURATION

TEST PROCEDURE
1. The EUT was set up for the max output power with pseudo random data modulation; 2. The power was measured with Spectrum Analyzer N9020A; 3. These measurements were done at 3 frequencies, 1850.20 MHz, 1880.00 MHz and 1909.80 MHz for
PCS1900 band; 824.20 MHz, 836.60 MHz and 848.80 MHz for GSM850 band. (Low, middle and high of operational frequency range).
TEST LIMIT
Part 24.238, Part 22.917 specify that the power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log (P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0 dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the specification from relative to absolute terms is carried out.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 31 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

TEST RESULTS

Test Mode GSM/TM1/GSM850 GSM/TM3/EDGE850 GSM/TM1/PCS1900 GSM/TM3/EDGE1900

Channel
128 190 251 128 190 251 512 661 810 512 661 810

Frequency (MHz)
824.2 836.6 848.8 824.2 836.6 848.8 1850.2 1880.0 1909.8 1850.2 1880.0 1909.8

Spurious RF Conducted Emission
(dBm) <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm <-13dBm

Limits (dBm)
-13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm

Remark: 1. Test results including cable loss; 2. Please refer to following plots; 3. Not reorded test plots from 9 KHz to 30 MHz as emission levels 20dB lower than emission limit;

Verdict PASS PASS PASS PASS

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 32 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port

GSM/TM1/GSM850

GSM/TM3/EDGE850

Channel 128 / 824.2 MHz

Channel 128 / 824.2 MHz

30 MHz ­ 1000 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 9 GHz Channel 190 / 836.6 MHz

1 GHz ­ 9 GHz Channel 190 / 836.6 MHz

30 MHz ­ 1000 MHz

30 MHz ­ 1000 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 33 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port

GSM/TM1/GSM850

GSM/TM3/EDGE850

Channel 190 / 836.6 MHz

Channel 190 / 836.6 MHz

1 GHz ­ 9 GHz Channel 251 / 848.8 MHz

1 GHz ­ 9 GHz Channel 251 / 848.8 MHz

30 MHz ­ 1000 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 9 GHz

1 GHz ­ 9 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 34 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM1/PCS1900
Channel 512 / 1850.2 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 35 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM1/PCS1900
Channel 661 / 1880 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 36 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM1/PCS1900
Channel 810 / 1909.8 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 37 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM3/EDGE1900
Channel 512 / 1850.2 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 38 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM3/EDGE1900
Channel 661 / 1880 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 39 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Spurious Emssion on Antenna Port GSM/TM3/EDGE1900
Channel 810 / 1909.8 MHz

30 MHz ­ 1000 MHz

1 GHz ­ 10 GHz

10 GHz ­ 20 GHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 40 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.6 Frequency Stability Test
TEST APPLICABLE
1. According to FCC Part 2 Section 2.1055 (a)(1), the frequency stability shall be measured with variation of ambient temperature from -30 to +50 centigrade.
2. According to FCC Part 2 Section 2.1055 (E) (2), for battery powered equipment, the frequency stability shall be measured with reducing primary supply voltage to the battery operating end point, which is specified by the manufacture.
3. Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried voltage equipment and the end voltage point was 3.3V.
TEST PROCEDURE
In order to measure the carrier frequency under the condition of AFC lock, it is necessary to make measurements with the EUT in a "call mode". This is accomplished with the use of R&S CMU200 DIGITAL RADIO COMMUNICATION TESTER.
1. Measure the carrier frequency at room temperature; 2. Subject the EUT to overnight soak at -30; 3. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on middle
channel of PCS 1900 and GSM850, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self-warming; 4. Repeat the above measurements at 10 increments from -30 to +50. Allow at least 0.5 hours at each temperature, unpowered, before making measurements; 5. Remeasure carrier frequency at room temperature with nominal voltage. Vary supply voltage from minimum voltage to maximum voltage, in 0.1Volt increments remeasuring carrier frequency at each voltage. Pause at nominal voltage for 0.5 hours unpowered, to allow any self-heating to stabilize, before continuing; 6. Subject the EUT to overnight soak at +50; 7. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on the centre channel, measure the carrier frequency. These measurements should be made within 2 minutes of Powering up the EUT, to prevent significant self-warming; 8. Repeat the above measurements at 10 increments from +50 to -30. Allow at least 0.5 hours at each temperature, unpowered, before making measurements; 9. At all temperature levels hold the temperature to +/- 0.5 during the measurement procedure;
TEST CONFIGURATION

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 41 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

TEST LIMITS

For Hand carried battery powered equipment According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability. The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section 2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the manufacturer. This transceiver is specified to operate with an input voltage of between 3.3VDC and 4.35VDC, with a nominal voltage of 3.8DC. Operation above or below these voltage limits is prohibited by transceiver software in order to prevent improper operation as well as to protect components from overstress. These voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these voltage limits are to be used.

For equipment powered by primary supply voltage According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability. The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment.

TEST RESULTS

DC Power
VL VN VH VN VN VN VN VN VN VN VN VN

Temperature ()
25 25 25 -30 -20 -10 0 10 20 30 40 50

GSM/TM1/GSM850

Frequency

Frequency

error(Hz)

error(ppm)

6

0.007

-37

-0.045

3

0.004

-36

-0.044

39

0.047

-38

-0.046

-14

-0.017

31

0.038

-1

-0.001

-50

-0.061

-46

-0.056

-26

-0.032

Limit (ppm)
2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50

Verdict
PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS

DC Power
VL VN VH VN VN VN VN VN VN VN VN VN

Temperature ()
25 25 25 -30 -20 -10 0 10 20 30 40 50

GSM/TM3/EDGE850

Frequency

Frequency

error(Hz)

error(ppm)

6

0.007

37

0.045

-40

-0.049

45

0.055

6

0.007

-23

-0.028

50

0.061

36

0.044

-5

-0.006

17

0.021

-44

-0.053

39

0.047

Limit (ppm)
2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50

Verdict
PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 42 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

DC Power
VL VN VH VN VN VN VN VN VN VN VN VN
DC Power
VL VN VH VN VN VN VN VN VN VN VN VN

Temperature () 25 25 25 -30 -20 -10 0 10 20 30 40 50
Temperature () 25 25 25 -30 -20 -10 0 10 20 30 40 50

GSM/TM1/PCS1900

Frequency

Frequency

error(Hz)

error(ppm)

47

0.025

-12

-0.006

-1

-0.001

-36

-0.019

24

0.013

17

0.009

1

0.001

-30

-0.016

-8

-0.004

-29

-0.015

26

0.014

-13

-0.007

GSM/TM3/EDGE1900

Frequency

Frequency

error(Hz)

error(ppm)

9

0.005

-33

-0.018

14

0.007

-46

-0.024

-39

-0.021

24

0.013

33

0.018

-43

-0.023

-31

-0.016

4

0.002

45

0.024

22

0.012

Limit (ppm) 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50
Limit (ppm) 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50 2.50

Verdict
PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS
Verdict
PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS PASS

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 43 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

4.7 Peak-to-Average Ratio (PAR)
LIMIT The Peak-to-Average Ratio (PAR) of the transmission may not exceed 13 dB. TEST CONFIGURATION

TEST PROCEDURE
Use spectrum to measure the total peak power and record as PPk. Use spectrum to measure the total average power and record as PAvg. Both the peak and average power levels must be expressed in the same logarithmic units (e.g., dBm). Determine the PAPR from: PAPR (dB) = PPk (dBm) - PAvg (dBm). Record the maximum PAPR level associated with a probability of 0.1%.

TEST RESULTS Test Mode
GSM/TM1/GSM850 GSM/TM3/EDGE850 GSM/TM1/PCS1900 GSM/TM3/EDGE1900

Channel
128 190 251 128 190 251 512 661 810 512 661 810

Frequency (MHz) 824.2 836.6 848.8 824.2 836.6 848.8 1850.20 1880.00 1909.80 1850.20 1880.00 1909.80

PAPR Value (dB) 2.63 2.62 2.62 5.40 5.38 5.42 2.65 2.67 2.67 5.30 5.22 5.36

Limits (dB) 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0

Verdict PASS PASS PASS PASS

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 44 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Peak-to-Average Ratio (PAR)

GSM/TM1/GSM850

GSM/TM3/EDGE850

Channel 128 / 824.2 MHz

Channel 128 / 824.2 MHz

Channel 190 / 836.6 MHz

Channel 190 / 836.6 MHz

Channel 251 / 848.8 MHz

Channel 251 / 848.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 45 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

Peak-to-Average Ratio (PAR)

GSM/TM1/PCS1900

GSM/TM3/EDGE1900

Channel 512 / 1850.2 MHz

Channel 512 / 1850.2 MHz

Channel 661 / 1880 MHz

Channel 661 / 1880 MHz

Channel 810 / 1909.8 MHz

Channel 810 / 1909.8 MHz

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity

Page 46 of 46

FCC ID: 2AZVY-L10

Report No.: LCSA022023062EG

5 TEST SETUP PHOTOGRAPHS OF EUT
Please refer to separated files for Test Setup Photos of the EUT.
6 EXTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for External Photos of the EUT.
7 INTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for Internal Photos of the EUT.

----------------THE END OF TEST REPORT---------------

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: [email protected] | Web: www.lcs-cert.com Scan code to check authenticity



Related FCC IDs:

Search Any Device: