Users Manual

Shantou Chenghai District Beihanhan Toy Factory YJ9901 2BHFO-YJ9901 2BHFOYJ9901 yj9901

Instruction Manual for Beihanhan Toy Factory models including: 2BHFO-YJ9901, 2BHFOYJ9901, YJ9901 Remote Control Car, YJ9901, Remote Control Car, Control Car, Car

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 2 Pages, 77.51KB

Document DEVICE REPORTGetApplicationAttachment.html?id=7464338 
Instruction manual
Any problems with the product
Note: p ease contact custome r s rvice (p lease do not bad rev iews
1.Remove the batteries timely if not use . 2. Input current and voltage: 4.2V/500 mA. 3.Play under adult's supervision. 4.Do not charge the battery for too long.
( Approx 30 min-1 hour for fully charge)
5 . Keep the battery in a cool and dry place .
Avoid storage in direct sunlight or near sources of heat
TROUBLESHOOTING:
Q:Not working or Stop working. A:1.Check if turn on the powerswitch.
(On the bottom of the car)
2.Take the battery out of the car and charge it for 30 minutes at least for the first time use.
3.Make sure the batteries you installed to the remote controller are brand new.
4.Check if there are some obstacles between the vehicle and remote controller.
(Signal would be interfered by appliances or WIFI). 5.Check if the light on the
remote controller is on whenpress the button. If not, please contact us to geta replacement controller

Battery lnstallation
power switch

Remote Controller 2x1.5V AA Batteries
How to Operate:

car 1xLl-ion Cell

1.Install 2*1.5V AA batteries to remote controller. 2.Connect the battery joint to the car's power joint.
Put the battery into the case and screw the battery cover. 3.Turn on the power switch of the car 4.Control the direction of this vehicle with remote controller.
Note:

1.Make sure to install the batteries in correct positive(+) and negative(-) polarities.
2.Screw the battery cover before use. 3.Rechargeable battery is recommend
How to Charge the Batteries

1.Connect the battery joint to the cable's joint. 2.Plug the USB port of the cable to your computer
to charge the battery. (4.2V / 500mA)

Package Include:

Remote Control Car X 1

LI-ion Cell

X2

Charge Cable

X1

Remote Controller X1

Mini Screw Driver X1

User Manual

X1

Us charging port is compatible with Power bank, Laptop and computers. (4.2V / 500mA)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

References

Related FCC IDs:

Search Any Device: