ST5（H2） 套装说明书v1.1
MOCREO ST5 WiFi Freezer Thermometer Alarm, Email Alert, App Notification, Data Logging Export, No Subscription Fee, Remote Temperature Sensor for Refrigerator, Freezer, Hot Tub (2 Pack)
ST5D-H2 User Manual (PDF) MOCREO MOCREO MOCREO,ST5,WiFi,Freezer,Thermometer,Alarm,,Email,Alert,,App,Notification,,Data,Logging,Export,,No,Subscription,Fee,,Remote,Temperature,Sensor,for,Refrigerator,,Freezer,,Hot,Tub,(2,Pack),,
User Manual (PDF)
MOCREO ST5 WiFi Freezer Thermometer Alarm, Email Alert, App Notification, Data Logging Export, No Subscription Fee, Remote Temperature Sensor for Refrigerator, Freezer, Hot Tub (2 Pack) : Home & Kitchen
User Manual for Mocreo models including: ST5D-H2 Wi-Fi Freezer Thermometer Alarm, ST5D-H2, Wi-Fi Freezer Thermometer Alarm, Freezer Thermometer Alarm, Thermometer Alarm, Alarm
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 1 Pages, 728.68KB
Document DEVICE REPORT91vX5dB MGLST5-H2 Temperature Sensors Kit User Manual Content Introduction ................................................................................... 2 What's in the Box .......................................................................... 3 Product Parameter........................................................................ 4 Power up the Hub ......................................................................... 6 Power Button Operation of the Hub.......................................... 7 Setup............................................................................................... 9 Installation...................................................................................... 17 Test the Effectve Distance............................................................ 18 How the System Works ................................................................ 19 Battery............................................................................................. 20 Calibration...................................................................................... 21 Configuration................................................................................. 22 Troubleshooting............................................................................ 23 Precautions for Use....................................................................... 26 FCC Statement ............................................................................... 27 Warranty......................................................................................... 29 Customer Service .......................................................................... 29 Disclaimer....................................................................................... 30 1 Introduction Welcome to the user manual for the ST5 Sensor, a device designed for monitoring temperature in a variety of settings. With its waterproof external probe, the ST5 Sensor can detect and record ambient temperature in real-time. Features: Detectable Temperature Range: -40°F ~ 257°F. Three Alarm Methods: E-Mail Alert, App Push Notification, Hub Beeping. The ST5 Sensor is suitable for a range of environments including refrigerators/freezers, hot tubs, fish tanks, pet cages and more. For example, if you are monitoring the temperature of a freezer, place the ST5 Sensor's data logger outside the freezer and place the probe inside to ensure reliable readings. 2 What's in the Box Hub (H2) x1 Micro USB Cable x1 Data Logger x2 4.9ft Probe Cable x2 Magic Sticker x2 3 Pin Clip x1 ST5 Temperature Sensors Kit User Manual User Manual x1 Product Parameter (1) ST5 Temperature Sensor 5V 1A Setup 3.5mm Indicator Light N/A Charging Port Pinhole Probe Port (Built in) Inductive Probe 3.5mm Male Plug Data Logger Specifications Sensor Probe Model Wireless Connection Communication Range Dimensions Weight (Including Probe) Battery (Rechargeable) Size of Stainless Steel Shell Cable Length Cable Cross Section Probe Measuring Rage Temperature Accuracy ST5 Bluetooth 131ft/40m (No Obstacles) 2.4 x 2.4 x 0.7 inch (L x W x H) 2.93 Ounces 3.7V 1800mAh Lithium Battery 6 mm in diameter 4.9ft 4mm x 1.3mm -40°F ~ 257°F (-40°C ~ 125°C) ±0.9°F (In the Range of 14°F to 185°F) 4 (2) Hub (H2) Plug Socket Power Button Indicator Light Specifications Model Weight Dimensions Input Output Wi-Fi Frequency Working Temperature Working Humidity H2 2.75 Ounces 3.46 x 1.48 x 2.05 inch (L x W x H) AC 100 ~ 240V 50/60Hz AC 100 ~ 240V 50/60Hz 10A 2.4 GHz 14°F ~ 50°F (-10°C ~ 40°C) 0 ~ 90%RH, No Condensation 5 LED Indicator Status Guides for Hub Indicator Light Purple Breathing Light Blue Breathing Light Red Breathing Light Red Flashing Light Status of Hub Normal Working Condition The Hub Is in Setup Mode Hub Is Not Connected to Wi-Fi An Alarm Event Is Triggered Sensor Models Compatible With H2 Hub ST5 Temperature Sensor ST6 Temp & Humidity Sensor SW2 Water Leak Sensor Power up the Hub Please plug the Hub into an outlet to power up the Hub, and it is recommended that the Hub be installed in a high, unobstructed location if possible to ensure stable signal transmission between the Hub and the Sensor. 6 The Socket on the Hub can be used to power other devices, please be careful not to overload, the maximum output current supported by the socket is 10A. Current 10A 1 2 Power Button Operation of the Hub 1. Short press 1s and then release. Control the switch of the socket, press to turn ON/OFF the power. When the Hub beeps because the Sensor triggers an alarm, a short press of the power button will temporarily turn off the Hub beep. Please note that in this case the function of controlling the socket switch will no longer be available. 7 2. Press and hold for 5s until the Hub indicator turns blue breathing light and release. At this point the Hub enters Setup Mode, which is required when adding the Hub via the App. If the Hub is already connected to the network and working properly, performing this operation again will put the Hub into Setup mode and the Hub will be disconnected from the network. 3. Press and hold for 15s until the Hub indicator turns red blinking light and release. This operation will reset the Hub to restore the factory settings, the previous configuration will be cleared and the network will need to be configured from scratch. The H2 Hub only support BLE Sensor (Refer to Page 6), after Hub reset, there is no need to re-add BLE Sensors, when Hub is reconfigured and added, BLE Sensor will be back online automatically. 8 Setup 1 Download MOCREO App Search "MOCREO Sensor" on Google Play/App Store or scan the QR Code below to download the MOCREO Sensor App and register a MOCREO account on the App (MOCREO will send you a confirmation Email, click on the confirmation to complete the registration). Google Play App Store MOCREO App 9 2 Setup Tutorial Please scan the QR code below to watch the setup turorial. 3 Turn on the Bluetooth Make sure the Bluetooth is ON during the whole setup process. For Android, please also enable GPS and agree to grant location permissions. 10 4 Add the Hub Open the MOCREO App, log into your MOCREO account. Tap the [+] Button at the upper right of the MOCREO Home Page to add a Hub. Note: The H2 Hub only support Wi-Fi connectivity. MOCREO Sensor No Hub linked yet? Click here to link a new one Select Product Hub Hub 11 5 Set the Hub Into Setup Mode Press and hold the power button of the Hub for 5s until the Hub indicator light turns blue. Enter Setup Mode Scanning Devices 5s Hub indicator light is blue? Continue Preparing to set up your device Scanning devices... Connected over BLE Read model/version OK Scanned 2.4GHz Wi-Fi APs 6 Select the Wi-Fi and Enter the Wi-Fi Password Select the Wi-Fi SSID you want to connect to and enter the Wi-Fi password, support 2.4GHz Wi-Fi Only. When "Congrats! Hub setup successfully!" appears on the page, it means the Hub is successfully added. Wi-Fi List Rescan Wi-Fi List xxxxxxxxxxx xxxxxxxxxxx xxxxxxxxxxx ...... Signal 71% Signal64% Signal55% Can't find your Wi-Fi? Click here The device connects to 2.4GHz WLAN only Wi-Fi Info Encryption Encrypted Wi-Fi SSID xxxxxxxxxxxxxxx Password Input the Wi-Fi password Connect Wi-Fi Connected Preparing to set up your device Connect the device to Wi-Fi AP Register the device to the cloud server Link the device to your account Waiting to sync device information Congrats! Hub setup successfully! Return To Homepage 12 13 7 Sensor Joins the Hub Tap the [+] Button at the upper right of the MOCREO Home Page and select Temp Sensor - ST5. Select Product No paired sensor? Click here. Temp Sensor - ST5 Note: Please make sure the Bluetooth of your mobile device (Smart phone/Tablet) is enabled during the whole setup process. The Bluetooth and GPS can be turned off after the Sensor setup is complete. 14 8 Select the Hub Select the Hub Unnamed MC90380C629088 9 Poke the Sensor Poke the Sensor pinhole with a pin for 1s and release, then the indicator light of Sensor will flash (Please complete this operation within 60 seconds, and you can add up to 10 Sensors at a time). 1s 15 10 Add the Sensor Select the Sensor you want to add and click on the "Add Button" (Up to 10 devices can be added at atime). When the appears on the Sensor card, it means the Sensor is successfully added. Please wait until all Sensors status to become complete. Add Devices 000030 Mac:30:AE:A4:00:00:30 000034 Mac:30:AE:A4:00:00:34 Add Add Devices 000030 Mac:30:AE:A4:00:00:30 000034 Mac:30:AE:A4:00:00:34 Home Installation 1. Please place the Hub at a relatively high position. The suggested distance between the Hub and Sensor is within 131ft (No obstacles, signal value stronger than 20% is ideal). 2. Please make sure the Sensor probe was inserted firmly (Note: ST5 probe is waterproof but the Sensor Data Logger is not). 3. Paste the Data Logger on the outside of refrigerator and place the probe inside. Test the Effectve Distance Place the paired ST5 Sensor in the location you want to monitor. The suggested distance between the Hub and Sensor is within 67ft-82ft (Household environment). Poke the Sensor pinhole for 1s and release. After 20~30 seconds, Tap the corresponding Sensor card on the App to reach the Sensor Settings Page and view the signal value, signal value stronger than 20% is ideal. 16 17 18 How the System Works The ST5 Sensors use Bluetooth to communicate with the Hub. Therefore, the distance are limited to a Bluetooth range centered on the Hub (e.g., around the house). This range is affected by distance and obstacles such as walls, windows, water, radio interference, etc. In short, longer distances and more obstacles mean weaker signals. The H2 Hub uses a Wi-Fi (2.4GHz only) to transmit data from the MOCREO Sensors in range to the Internet. A cellular hotspot with Wi-Fi capability can also be used to provide Internet access. Then, the MOCREO App can be used to view your device data from anywhere in the world. 19 Battery The ST5 Sensor built- in 1800mAh rechargeable lithium battery. The battery can last up to 2 years before it needs to be charged again. Please charge the Sensor with a Micro USB Cable and a 5V 1A power adapter. The battery percentage can be checked on the App: Sensor Settings Page>Battery Level (Please do not check the battery level while the device is charging). When charging, the red indicator light will stay on and when the red indicator light goes off it means charging is complete. Low battery alert will be triggered when the battery is below 10% (Including Email alerts and APP notification). 20 Calibration When the Sensor was taken to or from the refrigerator/ freezer, the ST5 Sensor will spend some time calibrating the reading, and it would take about 20 minutes for the ST5 to measure to proper ambient temperature. The ST5 has a built-in USA-made DS18B20 chip, which is a strictly calibrated industrial-grade chip and is more accurate than ordinary consumer chips. Calibration is usually not required, if you need information about the chip, please check the FAQ. Calibration is only used to correct for small variations of ±0.9°F (±0.5°C). If you find larger differences than this during calibration, which indicates a problem with the calibration process of your Sensor, please contact MOCREO Customer Service. 21 Configuration }Name the Sensor~Tap Sensor Card > Button on the Upper Right > Alias Name > Save }Name the Hub~Tap Button on the Upper Left > Hubs > Click Button on the Hub Card > Name > Save }Alert~Tap Button on the Upper Left > Alerts > Set Alert Model > Save }Export Data~Tap Sensor Card > Button on the Upper Right > Export Historical Data > Choose Time Period > Export 22 Troubleshooting 1. Hub offline/unable to access the Internet. a. Please check whether the Hub is online. Open the App and click [Menu], then click [Hubs] to check the color of your Hub card. If the Hub card is gray, it means the Hub is offline. If the Hub card is green, it means the Hub is online. b. Please check that the indicator light of the Hub is on. If not, make sure the device is properly connected and powered. If the indicator light is red, it means that the current network is disconnected/network is not good. You can try moving the Hub closer to the router or restarting the Hub to restore the network connection. 23 2. Sensor Failed to Add? a. The App can't scan the Sensor in the Sensor setup process. Please make sure your phone is within 15ft from the Sensor. Please check whether ST5 Sensor has entered setup mode (Poke Sensor for 1s, blue LED will flashing, which means the Sensor enters Setup mode). Please do not turn off the Bluetooth and network on your phone (Android needs to open the GPS and authorize the positioning permission). b. When adding a Sensor, the App scanned Sensor but did not add successfully Click "Retry Button" on the page to re-add. If the Sensor still can't be added, please contact MOCREO Support for help. 24 Note: a. To improve wireless stability, it is recommended: Install the Sensor as close to the Hub as possible. It's better if the Hub and the Sensor are in sight. Reduce the obstacles between the Hub and the Sensor. The Hub and Sensor should be placed far away from wate to avoid signal interference. Stay away from high power equipment, flammable and explosive materials. b. Precautions about the Sensor placement environment. The Data Logger is non-waterproof, please avoid water submerging and extreme temperature. The working temperature range of the Sensor is from -40°F to +257°F (-40°C to +125°C). When exceeding this range, the data monitored might be inaccurate or the Sensor might be damaged. The battery is rechargeable. It can be charged with the micro USB cable equipped. But the battery is not removable. 25 Precautions for Use To ensure the normal use of the product, please pay attention to the following situations: It is recommended to install the Hub in a high place. Do not expose the Device to high temperatures, humidity, or dusty environments. Do not place the Device near flammable materials. Do not put heavy objects on the Device or use it as a support. Children should not use the Device without adult supervision. 26 FCC Statement FCC ID (Sensor) : 2A36D-ST4 FCC ID (Hub) : 2A36D-H1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 27 These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 28 Warranty MOCREO products enjoy a 12-Month limited warranty (Start from the date when customer receives the product), which applies only to hardware components of the device that are not subject to accident, misuse, neglect, fire, or other external causes, alterations, repair. Customer Service https://mocreo.com/doc/manual/support/faq.html +1 (530) 988-8608 [email protected] MOCREO Sensor Search [ MOCREO Sensor ] on YouTube to watch the setup video tutorials. 29 Disclaimer The contents about how to use the product and the App guidance are only for reference, please refer to the actual situation for specific application. If there is something differs from the instruction during using the product, please contact MOCREO Support for updates. This product is for detecting and monitoring only, MOCREO is not responsible for any property damage or other consequences of the use of this product. (v1.1) 30
FAQ — MOCREO 0.1.0 documentation