Test Report

Continental Conair Limited FS2000AT 14 Channel Family Radio Service LBBFS2000AT LBBFS2000AT fs2000at

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 54 Pages, 88.63KB

Document DEVICE REPORTGetApplicationAttachment.html?id=162706
Continental Conair Limited
Application For
Certification (FCC ID: LBBFS2000AT)
July 17, 2001

WO# 0104907 WL/Sandy July 17, 2001

·

The test results reported in this report shall refer only to the sample actually tested and shall not refer or be deemed a refer to bulk from which such a sample may be said to have

been obtained.

·

This report shall not be reproduced except in full without prior authorization from Intertek Testing Services Hong Kong Limited

·

For Terms And Conditions of the services, it can be provided upon request.

Intertek Testing Services Hong Kong Ltd.
2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487

INTERTEK TESTING SERVICES SUMMARY OF CONTENTS LIST OF EXHIBITS

EXHIBIT 1: EXHIBIT 2: EXHIBIT 3: EXHIBIT 4: EXHIBIT 5: EXHIBIT 6: EXHIBIT 7: EXHIBIT 8: EXHIBIT 9: EXHIBIT 10: EXHIBIT 11: EXHIBIT 12: EXHIBIT 13:

General Description System Test Configuration RF Power Output Modulation Characteristics Occupied Bandwidth Spurious Emission Frequency Stability Technical Specifications Product Labelling Photographs Instruction Manual Tune Up Procedure Part List

FCC ID: LBBFS2000AT i

INTERTEK TESTING SERVICES

MEASUREMENT/TECHNICAL REPORT

Application

:

Trade Name/Model No :

Date

:

Continental Conair Limited Southwestern Bell Freedom Phone FS2000 Southwestern Bell Freedom Phone FS2000T Southwestern Bell Freedom Phone FS870 July 17, 2001

This report concerns (check one:)Original Grant X

Class II Change

Equipment Type: Family Radio Service, FRS

Deferred grant requested per 47 CFR 0.457(d)(1)(ii)?

Yes

If yes, defer until:

Company Name agrees to notify the Commission by: date

No X date

of the intended date of announcement of the product so that the grant can be issued on that date.

Report prepared by:

Wilson Loke Intertek Testing Services. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Phone: 852-2173-8575 Fax: 852-2745-8306

FCC ID: LBBFS2000AT ii

INTERTEK TESTING SERVICES
Table of Contents
1.0 General Description ................................................................................................................ 2 1.1 Product Description ............................................................................................................ 2 1.2 Ralated Submittal(s) Grants ................................................................................................ 3 1.3 Test Methodology ............................................................................................................... 3 1.4 Test Facility......................................................................................................................... 3
2.0 System Test Configuration...................................................................................................... 5 2.1 Justification ......................................................................................................................... 5 2.2 EUT Exercising Software.................................................................................................... 6 2.3 Special Accessories ............................................................................................................. 6 2.4 Equipment Modification ..................................................................................................... 6
3.0 RF Output Power (Section 95.639(d)) ................................................................................... 8 4.0 Modulation Characteristics (Section 95.637(a))................................................................. 12
4.1 Modulation Frequiency Response ..................................................................................... 14 4.2 Modulation Limiting Characteristic................................................................................... 16 5.0 Occupied Bandwidth (Section 95.633(c).............................................................................. 17
6.0 Spurious Emission (Section 95.635(b)) ................................................................................ 20 6.1 Field Strength of Spurious Radiation ................................................................................ 21
7.0 Frequency Stanility (Section 95.627)................................................................................... 27 7.1 Frequency Tolerance......................................................................................................... 28 7.2 Temperature Extreme Condition....................................................................................... 30 7.3 Voltage Extreme Condition ............................................................................................... 33
8.0 Technical Specifications........................................................................................................ 36 9.0 Product Labelling.................................................................................................................. 40 10.0 Equipment Photographs ..................................................................................................... 43 11.0 Instruction Mannal.............................................................................................................. 45 12.0 Tune Up Procedure ............................................................................................................. 47 13.0 Part List................................................................................................................................ 49
FCC ID: LBBFS2000AT iii

INTERTEK TESTING SERVICES
List of attached file

Exhibit type Operation Description Test Report Test Report Test Report Test Report Block Diagram Schematics ID Label/Location User Manual Test Report Test Setup Photo Internal Photo External Photo Test Report Test Report

File Description Technical Description Bandwidth Plot Modulation Frequency Response Modulation Limit Characteristic Spurious Emission Block Diagram Circuit Diagram Label Artwork and Location User Manual Test Report Radiated Emission Internal Photo External Photo Tune Up Procedure Part List

Filename descri.pdf bw.pdf mfr.pdf mlc.pdf spurious.pdf block.pdf circuit.pdf label.pdf manual.pdf report.doc radiated1.jpg to radiated2.jpg iphoto1.jpg to iphoto3.jpg ophoto1.jpg to ophoto2.jpg tuneup.pdf partlist.pdf

FCC ID: LBBFS2000AT iv

INTERTEK TESTING SERVICES EXHIBIT 1
GENERAL DESCRIPTION
FCC ID: LBBFS2000AT 1

INTERTEK TESTING SERVICES
1.0 General Description 1.1 Product Description
The Equipment Under Test (EUT) is a 14-Channel FRS operating at 462.5625 to 467.7125MHz. The EUT is powered by 6V batteries (4 x 1.5V "AAA" battery or 1 pack 4.8V 350mAh Ni-Cd battery). The input current to the EUT at 6.0V d.c. is 160mA. Transmitter Portion i) Type of Emission: 5K7F3E ii) Frequency Range: 462.5625 to 467.7125MHz iii) Maximum Power Rating: 0.44W The brief circuit description is saved with filename: descri.pdf
FCC ID: LBBFS2000AT 2

INTERTEK TESTING SERVICES
1.2 Related Submittal(s) Grants This is an Application for Certification of the transmitter portion of a FRS Transceiver. The receiver section of the FRS Transceiver is subject to verification process.
1.3 Test Methodology Radiated emission measurements were performed according to the procedures in ANSI C63.4 (1992). All measurement were performed in Open Area Test Sites. Preliminary scans were performed in the Open Area Test Sites only to determine worst case modes. For each scan, the procedure of maximizing emissions in Appendices D and E were followed. All Radiated tests were performed at an antenna the EUT distance of 3 meters, unless stated otherwise in the "Justification Section" of this Application.
1.4 Test Facility The open area test site and conducted measurement facility used to collect the emission data is located at Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. The test facility and site measurement data have been fully placed on file with the FCC.
FCC ID: LBBFS2000AT 3

INTERTEK TESTING SERVICES EXHIBIT 2
SYSTEM TEST CONFIGURATION
FCC ID: LBBFS2000AT 4

INTERTEK TESTING SERVICES
2.0 System Test Configuration 2.1 Justification
The device was configured for testing in a typical fashion (as a customer would normally use it). The device was placed on a turntable, which enabled the engineer to maximize emissions through its placement in the three orthogonal axes. When the radiated emissions are measured. The device was powered by 4 x fully charged 1.5V "AAA" battery or 1 pack 4.8V 350mAh Ni-Cd battery. The frequency range from 30 MHz to 10th harmonics was searched for spurious emissions from the device. Only those emissions reported were detected. All other emissions were at least 20 dB below the applicable limits.
FCC ID: LBBFS2000AT 5

INTERTEK TESTING SERVICES
2.2 EUT Exercising Software There was no special software to exercise the device. Once the unit is powered on, a signal is transmitted.
2.3 Special Accessories A special headset is provided by client for compliance of this device.
2.4 Equipment Modification Any modification installed previous to testing by Continental Conair Limited will be incorporated in each production model sold/leased in the United States. No modification were installed by Intertek Testing Services.
Confirmed by: Wilson Loke Manager Intertek Testing Services Agent for Continental Conair Limited

July 17, 2001

Signature Date

FCC ID: LBBFS2000AT 6

INTERTEK TESTING SERVICES EXHIBIT 3
RF POWER OUTPUT
FCC ID: LBBFS2000AT 7

INTERTEK TESTING SERVICES

3.0 RF Power Output (Section 2.1046(a))

A. Equipment Used
Equipment Biconical Antenna Test receiver RF Filter Tuned Dipole Antenna Signal Generator

Brand Name CDI Rohde & Schwarz Tailithic CDI Maconi

Model No. B300 ESVS30 3VF Robert Antenna 4 2024

B. Testing Procedure

1. On a test site, the EUT shall be placed at 1.5m height on a turn table, and in the position closest to normal use as declared by the applicant.

2. The test antenna shall be oriented initially for vertical polarisation located 3m from EUT to correspond to the frequency of the transmitter.

3. The output of the test antenna shall be connected to the measuring receiver and the quasi-peak detector is used for the measurement.

4. The transmitter shall be switched on, if possible, without modulation and the measuring receiver shall be tuned to the frequency of the transmitter under test.

5. The test antenna shall be raised and lowered through the specified range of height until a maximum signal level is detected by the measuring receiver.

FCC ID: LBBFS2000AT 8

INTERTEK TESTING SERVICES
6. The transmitter shall then the rotated through 360° in the horizontal plane, until the maximum signal level is detected by the measuring receiver.
7. The test antenna shall be raised and lowered again through the specified range of height until a maximum signal level is detected by the measuring receiver.
8. The maximum signal level detected by the measuring receiver shall be noted. 9. The transmitter shall be replaced by a tuned dipole (substitution antenna). 10. The substitution antenna shall be orientated for vertical polarisation and the length
of the substitution antenna shall be adjusted to correspond to the frequency of the transmitter. 11. The substitution antenna shall be connected to a calibrated signal generator. 12. If necessary, the input attenuator setting of the measuring receiver shall be adjusted in order to increase the sensitivity of the measuring receiver. 13. The test antenna shall be raised and lowered through the specified range of height to ensure that the maximum signal is received. 14. The input signal to the substitution antenna shall be adjusted to the level that produces a level detected by the measuring received, that is equal to the level noted while the transmitter radiated power was measured, corrected for the change of input attenuator setting of the measuring receiver. 15. The input level to the substitution antenna shall be recorded as power level in dBm, corrected for any change of input attenuator setting of the measuring receiver. 16. The measurement shall be repeated with the test antenna and the substitution antenna orientated for horizontal polarisation. 17. The measure of the effective radiated power is the larger of the two levels recorded, at the input to the substitution antenna, corrected for gain of the substitution antenna if necessary.
FCC ID: LBBFS2000AT 9

INTERTEK TESTING SERVICES

Table 1

Continental Conair Limited Southwestern Bell Freedom Phone FS2000

Transmission Power

Channel
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Frequency (M H z)
462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 467.6625 467.6875 467.7125

Effectived Radiated Pow er(W ) 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44 0.44

Lim it (W ) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

M argin (W ) -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06 -0.06

Notes: Negative sign in the margin column shows the value below limits.

Test Engineer: Ben W. K. Ho FCC ID: LBBFS2000AT

Date of Test: May 23, 2001 10

INTERTEK TESTING SERVICES EXHIBIT 4
MODULATION CHARACTERISTICS
FCC ID: LBBFS2000AT 11

INTERTEK TESTING SERVICES
4.0 Modulation Characteristics In order to satisfy the 95.637(a) requirement, Modulation Frequency Response and Modulation Limit Characteristics are attached in Exhibit 4.1 & 4.2. Plots for each tests are saved with filename: mfr.pdf and mlc.pdf
FCC ID: LBBFS2000AT 12

INTERTEK TESTING SERVICES
4.1 Modulation Frequency Response A. Test Equipment

Equipment Audio Signal Generator dB meter 20 dB RF Load Modulation Meter

Brand Name Leader Leader Bird Marconi Instrument

Model No. LFG-1300S LMV-182A 8304-200-N 2945

B. Testing Procedure 1) Set-up the test equipment in the following configuration:

Modulation

EUT

20dB Load

Meter

Audio Signal Generator

dB Meter

2) Set the audio signal generator frequency to the sound pressure level 97.0dBSPL at the microphone of the EUT.
3) The frequency of the audio signal generator is changed form 300Hz to 5kHz. 4) Record the frequency deviation.

FCC ID: LBBFS2000AT 13

INTERTEK TESTING SERVICES

C. Test Result

Table 2

Continental Conair Limited Southwestern Bell Freedom Phone FS2000

Modulation Frequency Response

Test Channel : 4 Input level = 97.0dBSPL
M odulation Frequency (H z) 200 300 400 500 600 700 800 900 1000 1250 1500 1750 2000 2250 2500 2750 3000 3125 3250 3500 4000 5000

M odulation index (% ) 0.40 0.80 2.85 3.12 3.13 2.94 2.63 2.19 1.94 1.40 1.08 0.87 0.70 0.56 0.44
0.33
0.24 0.20 0.15 0.13 0.08 0.03

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 14

INTERTEK TESTING SERVICES
4.2 Modulation Limiting Characteristics (Section 2.1047(b)) A. Test Equipment

Equipment Audio Signal Generator 20 dB RF Load Modulation Meter

Brand Name Leader Bird Marconi

Model No. LFG-1300S 8304-200-N 2950

B. Testing Procedure

1) Set-up the test equipment in the following configuration:

Modulation

EUT

20dB Load

Meter

Audio Signal Generator
2) Set the frequency of the audio signal generator to 500Hz and adjust the level from 47dBSPL to 127dBSPL.
3) Record the maximum value of plus or minus peak frequency deviation. 4) Repeat the above procedure with frequency 1000Hz, 2500Hz & 3125Hz.

FCC ID: LBBFS2000AT 15

INTERTEK TESTING SERVICES
C. Test Result

Table 3
Continental Conair Limited Southwestern Bell Freedom Phone FS2000
Modulation Limiting Characteristics

Test Channel : 4

M odulation Input
(dBSPL) 47 57 67 77 87 97 107 117 127 137

Peak Frequency Deviation (kH z)
at500H z 0.09 0.11 0.21 0.54 1.60 2.28 2.40 2.45 2.42 2.41

Peak Frequency Deviation (kH z)
at1000H z 0.09 0.15 0.36 1.04 1.94 2.04 2.03 2.01 2.01 2.03

Peak Frequency Deviation (kH z)
at2500H z 0.10 0.17 0.41 1.00 1.11 1.10 1.08 1.06 1.07 1.11

Peak Frequency Deviation (kH z)
at3125H z 0.08 0.10 0.16 0.38 0.63 0.64 0.64 0.67 0.67 0.67

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 16

INTERTEK TESTING SERVICES EXHIBIT 5
OCCUPIED BANDWIDTH
FCC ID: LBBFS2000AT 17

INTERTEK TESTING SERVICES
5.0 Occupied Bandwidth (Section 95.633(c)) A. Test Equipment

Equipment Audio Signal Generator dB meter 20 dB RF Load Spectrum Analyzer

Brand Name Leader Leader Bird Hewlett Packard

Model No. LFG-1300S LMV-182A 8304-200-N 8951EM

B. Testing Procedure

1) Set-up the test equipment in the following configuration:

Spectrum

EUT

20dB Load

Analyzer

Audio Signal Generator

dB Meter

2) Set the level of audio signal generator to obtain 16 dB greater than required for 50% modulation.
3) The occupied bandwidth is measured with the spectrum analyzer set at 5kHz/div scan and 10dB/div.
C. Test Result
The occupied Bandwidth is measured to be 5.7 kHz.
For the electronic filing, the bandwidth plot is saved with filename: bw.pdf

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 18

INTERTEK TESTING SERVICES EXHIBIT 6
SPURIOUS EMISSION
FCC ID: LBBFS2000AT 19

INTERTEK TESTING SERVICES
6.0 Spurious Emission (Section 95.635) In order to satisfy the 95.635 requirement, the spurious emission from the EUT are measured and shown in the Exhibit 6.1.
FCC ID: LBBFS2000AT 20

INTERTEK TESTING SERVICES
6.1 Field Strength of Spurious Radiation (Section 95.635) A. Test Equipment

Equipment Antenna Test receiver RF Filter

Brand Name CDI Rohde & Schwarz Tailithic

Model No. B100,B200,B300, Horn ESVS30 3VF

B. Testing Procedure
Radiated emission measurements were performed according to the procedures in ANSI C63.4(1992). All measurements were performed in Open Area Test Sites located at Roof Top of Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong.

FCC ID: LBBFS2000AT 21

INTERTEK TESTING SERVICES
C. Radiated Emission Configuration Photograph Worst Case Radiated Emission
For electronic filing, the radiated emission configurations photograph is saved with filename: radiated1.jpg and radiated2.jpg
FCC ID: LBBFS2000AT 22

C. Test Result

INTERTEK TESTING SERVICES

Continental Conair Limited Southwestern Bell Freedom Phone FS2000
Table 4(a)
1. Unwanted emission from CARRIER ±6.25kHz to Carrier ± 31.25kHz (Refer to the plots which is saved with filename: spurious.pdf)

Region CARRIER ± 6.25kHz to ± 12.5kHz CARRIER ± 12.5kHz to ± 31.25kHz

Unwanted emission

Channel 4

Channel 11

<25dB

<25dB

<35dB

<35dB

FCC ID: LBBFS2000AT 23

INTERTEK TESTING SERVICES

Table 4(b): Channel 4

O rientation
H V V V H H H

Frequency (M H z)
925.228 1387.903 1850.533 2313.173 2775.803 3238.417 3701.031

Reading
(dBµV)
41.7 70.3 76.4 69.7 65.1 60.8 60.6

Pre- Antenna Am p Factor (dB) (dB)
16 22.8 34 24.2 34 26.5 34 29.1 34 29.1 34 31.4 34 32.8

Calculated Calculated

Net

Lim it

at 3m

at3m *

(dBµV/m ) (dBµV/m )

48.5

82.2

60.5

82.2

68.9

82.2

64.8

82.2

60.2

82.2

58.2

82.2

59.4

82.2

M argin (dB)
-33.7 -21.7 -13.3 -17.4 -22.0 -24.0 -22.8

Remark: 1. Quasi-peak data for emission below 1000MHz. 2. `-` sign in margin column shows the value below the limits. 3. Any emissions and any other harmonics which are attenuated more than 20dB below the permissible value need not be recorded. 4. Horn Antenna and average detector is used for emission over 1000MHz. * Calculated limit = 10 log10 (TP(W)) - 43 - 10 log10 (TP) = -43dBW = 82.2dBµV/m at 3m

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 24

INTERTEK TESTING SERVICES

Table 4(b): Channel 11

O rientation
H V V V H H H

Frequency (M H z)
935.228 1402.841 1870.456 2338.050 2805.654 3273.268 3740.882

Reading
(dBµV)
42.8 70.4 76.2 69.8 65.2 61.5 60.7

Pre- Antenna Am p Factor (dB) (dB)
16 22.8 34 24.2 34 26.5 34 29.1 34 29.1 34 31.4 34 32.8

Calculated Calculated

Net

Lim it

at 3m

at3m *

(dBµV/m ) (dBµV/m )

49.6

82.2

60.6

82.2

68.7

82.2

64.9

82.2

60.3

82.2

58.9

82.2

59.5

82.2

M argin (dB)
-32.6 -21.6 -13.5 -17.3 -21.9 -23.3 -22.7

Remark: 1. Quasi-peak data for emission below 1000MHz. 2. `-` sign in margin column shows the value below the limits. 3. Any emissions and any other harmonics which are attenuated more than 20dB below the permissible value need not be recorded. 4. Horn Antenna and average detector is used for emission over 1000MHz. * Calculated limit = 10 log10 (TP(W)) - 43 - 10 log10 (TP) = -43dBW = 82.2dBµV/m at 3m

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 25

INTERTEK TESTING SERVICES EXHIBIT 7
FREQUENCY STABILITY
FCC ID: LBBFS2000AT 26

INTERTEK TESTING SERVICES
7.0 Frequency Stability The frequency tolerance was tested in normal condition & over extreme ambient conditions with respect to voltage and temperature variation.
FCC ID: LBBFS2000AT 27

INTERTEK TESTING SERVICES
7.1 Frequency Tolerance (Section 95.625) A. Test Equipment

Equipment Regulated Power Supply 20 dB RF Load Frequency Counter

Brand Name PAD Bird Phillips

Model No. 30-35L 8304-200-N PM6668

B. Testing Procedure 1) Set-up the test equipment in the following configuration:

Frequency

EUT

20dB Load

Counter

2) Measure all transmit channel frequencies in MHz.

FCC ID: LBBFS2000AT 28

INTERTEK TESTING SERVICES
C. Test Result

Table 5

Continental Conair Limited Southwestern Bell Freedom Phone FS2000

Frequency Tolerance

Channel
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Frequency (M H z)
462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 467.6625 467.6875 467.7125

M easured Frequency (M H z)
462.56192 462.58691 462.61191 462.63690 462.66189 462.68689 462.71189 467.56188 467.58688 467.61180 467.63696 467.66194 467.68693 467.71192

Tolerance (% )
0.000125 0.000128 0.000128 0.000130 0.000132 0.000132 0.000132 0.000133 0.000133 0.000150 0.000115 0.000120 0.000122 0.000124

FCC ID: LBBFS2000AT 29

INTERTEK TESTING SERVICES
7.2 Frequency Stability - Temperature (Section 2.1055) A. Test Equipment

Equipment 20 dB RF Load Frequency Counter

Brand Name Bird Phillips

Model No. 8304-200-N PM6668

B. Testing Procedure

1) Set-up the test equipment in the following configuration:

Temperature Chamber

Frequency

EUT

20dB Load

Counter

2) Set the Temperature Chamber to -20°C and stabilize the EUT temperature for one hour. Set transmitter ON for two minutes.
3) Measure the channel frequency of channel 4, 11 in MHz. 4) Turn the EUT OFF 5) Repeat the above procedure from -20°C to 50°C with 10°C increment.

FCC ID: LBBFS2000AT 30

INTERTEK TESTING SERVICES
C. Test Result

Table 6(a)
Continental Conair Limited Southwestern Bell Freedom Phone FS2000
Frequency Deviation with Temperature Variation

Channel : 4

Tem perature (°C ) A ssigned Frequency

(M H z)

-20

462.6375

-10

462.6375

0

462.6375

10

462.6375

20

462.6375

30

462.6375

40

462.6375

50

462.6375

M easured Frequency (M H z)
462.63786 462.63742 462.63727 462.63740 462.63690 462.63707 462.63698 462.63722

% D eviation
-0.000078 0.000017 0.000050 0.000022 0.000130 0.000093 0.000112 0.000061

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 31

INTERTEK TESTING SERVICES
C. Test Result

Table 6(b)
Continental Conair Limited Southwestern Bell Freedom Phone FS2000
Frequency Deviation with Temperature Variation

Channel : 4

Tem perature (°C ) A ssigned Frequency

(M H z)

-20

467.6375

-10

467.6375

0

467.6375

10

467.6375

20

467.6375

30

467.6375

40

467.6375

50

467.6375

M easured Frequency (M H z)
467.63779 467.63766 467.63726 467.63744 467.63696 467.63705 467.63701 467.63716

% D eviation
-0.000062 -0.000034 0.000051 0.000013 0.000115 0.000096 0.000105 0.000073

Test Engineer: Ben W. K. Ho

Date of Test: May 23, 2001

FCC ID: LBBFS2000AT 32

INTERTEK TESTING SERVICES
7.3 Frequency Stability - Voltage (Section 2.995) A. Test Equipment

Equipment Regulated Power Supply 20 dB RF Load Voltage meter Frequency Counter

Brand Name PAD Bird Fluke Phillips

Model No. 30-35L 8304-200-N 87 PM6668

B. Testing Procedure 1) Set-up the test equipment in the following configuration:

Regulated Power Supply

Frequency

EUT

20dB Load

Counter

Voltmeter
2) Vary the level of regulated power supply to the manufacturer specified battery end point of the EUT.
3) Measure the channel frequency from channel 1 to 14 in MHz.

FCC ID: LBBFS2000AT 33

INTERTEK TESTING SERVICES

C. Test Result

Table 7

Continental Conair Limited Southwestern Bell Freedom Phone FS2000

Frequency Deviation with Voltage Variation

The manufacturer specified battery end point 4.4V

Channel
4 11

Frequency (M H z)
462.6375 467.6375

M easured Frequency (M H z)
462.63698 467.63696

Tolerance (% )
-0.000112 -0.000115

FCC ID: LBBFS2000AT 34

INTERTEK TESTING SERVICES EXHIBIT 8
TECHNICAL SPECIFICATIONS
FCC ID: LBBFS2000AT 35

INTERTEK TESTING SERVICES
8.0 Technical Specifications
FCC ID: LBBFS2000AT 36

INTERTEK TESTING SERVICES
8.1 Block Diagram For electronic filing, the block diagram of the FRS is saved with filename: block.pdf Figure 8.1 Block Diagram
FCC ID: LBBFS2000AT 37

INTERTEK TESTING SERVICES
8.2 Schematic Diagram For electronic filing, the schematic diagram of the FRS is saved with filename: circuit.pdf Figure 8.2 Schematic Diagram
FCC ID: LBBFS2000AT 38

INTERTEK TESTING SERVICES EXHIBIT 9
PRODUCT LABELLING
FCC ID: LBBFS2000AT 39

INTERTEK TESTING SERVICES
9.0 Product Labelling
FCC ID: LBBFS2000AT 40

INTERTEK TESTING SERVICES
9.1 Label Artwork & Location Figure 9.1 Label Artwork & Location
An engineering drawing of the label which will be permanently affixed to the unit. For electronic filing, the label artwork & location are saved with filename: label.pdf
FCC ID: LBBFS2000AT 41

INTERTEK TESTING SERVICES EXHIBIT 10
PHOTOGRAPHS
FCC ID: LBBFS2000AT 42

INTERTEK TESTING SERVICES
10.0 Equipment Photographs For electronic filing, photographs of the tested EUT are saved with filename: ophoto1.jpg to ophoto2.jpg for external photo and iphoto1.jpg to iphoto3.jpg for internal photo.
FCC ID: LBBFS2000AT 43

INTERTEK TESTING SERVICES EXHIBIT 11
INSTRUCTION MANUAL
FCC ID: LBBFS2000AT 44

INTERTEK TESTING SERVICES
11.0 Instruction Manual This manual will be provided to the end-user with each unit sold/leased in the United States. For electronic filing, a preliminary copy of the Instruction Manual is saved with filename: manual.pdf
FCC ID: LBBFS2000AT 45

INTERTEK TESTING SERVICES EXHIBIT 12
TUNE UP PROCEDURE
FCC ID: LBBFS2000AT 46

INTERTEK TESTING SERVICES
12.0 Tune Up Procedure For electronic filing, a preliminary copy of the Tune Up Procedure is saved with filename: tuneup.pdf
FCC ID: LBBFS2000AT 47

INTERTEK TESTING SERVICES EXHIBIT 13 PART LIST
FCC ID: LBBFS2000AT 48

INTERTEK TESTING SERVICES
13.0 Part List For electronic filing, a preliminary copy of the Part List is saved with filename: partlist.pdf
FCC ID: LBBFS2000AT 49



Related FCC IDs:

Search Any Device: