Modular Approval Request (per DA 00-1407)
bvos
Modular Approval Request
Datalogic S.r.l. SIRIUS915 Radio module U4F-SIRIUS915 U4FSIRIUS915 sirius915
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 2 Pages, 72.72KB
Document DEVICE REPORTGetApplicationAttachment.html?id=7988882RF_734_05 FCC Modular Approval Request Page 1 of 3 28-12-2022 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) This modular transceiver is approved for use by the Grantee in its own products and not intended for sale. FCC ID: U4F-SIRIUS915 Items to be covered by Single modular transmitters. 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. Answer from applicant YES, see photo below 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. 3. The module must contain power supply regulation on the module 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). The radio module has buffered modulation/data inputs to ensure that the module complies with Part 15 requirements under conditions of excessive data rates or overmodulation YES, the module contains power supply regulator YES, the module has UFL connector 5.The module must demonstrate compliance in a stand-alone configuration. 6.The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748). YES, the module has been tested using a test board to supply the module and send test commands YES, see photo below 7.The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. 8.The module must comply with RF exposure requirements. YES, module has been tested according to FCC 15.247 regulation Module complies with the requirements of RF Exposure portable devices INTERNAL Datalogic Confidential RF_734_05 FCC Modular Approval Request Page 2 of 3 28-12-2022 Items to be covered by Split modular transmitters. 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. Answer from applicant 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Ruggero Cacioppo Date: November 18th 2024 Signature: INTERNAL Datalogic Confidential
Related FCC IDs:
- U4F-SIRIUS915 - Datalogic S.r.l. Radio module [-SIRIUS915] Microsoft Word for Microsoft 365