AP460C, AP460S6C, AP460S12C ExtremeWireless Access Points Quick Reference

AP460C access point, AP460C support

Extreme Networks

AP460C, AP460S6C, and AP460S12C Access Points Quick Reference Guide Mar 2021

AP460C, AP460S6C, and AP460S12C - Extreme Networks

AP460C, AP460S6C, AP460S12C ExtremeWireless Access ...

26 set 2022 — 4×4:4 data rates concurrently on the 2.4 GHz and 5 GHz radios, with a third ... AP460S6C, AP460S12C Access Points Installation Guide in the Extreme Networks.

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 2 Pages, 396.12KB

Document DEVICE REPORTAP460C QuickRef
ExtremeWireless 802.11ax AP460C, AP460S6C, AP460S12C Outdoor Access Points
AP460C, AP460S6C, AP460S12C Overview
AP460C, AP460S6C, and AP460S12C tri-radio 802.11ax access points are based on advanced radio technology and IP67 rated for harsh and extreme outdoor environments, with an extended temperature range. The tri-radio design delivers 802.11ax 2×2:2 and 4×4:4 data rates concurrently on the 2.4 GHz and 5 GHz radios, with a third radio as a dedicated dual-band sensor. The access point can be installed on an outdoor environment on a vertical or horizontal pole, or to a flat surface.
Note: The installation procedures covered in this document is applicable to all three access points and they are collectively addressed as AP460C.

The AP460C, AP460S6C, AP460S12C access points have the following features: · Radios:
­ Three 802.11a/b/g/n/ac/ax radios (one 4×4 radio, one 2×2 radio, and one 1×1 scanner radio)
­ One Bluetooth Low Energy (BLE) radio · Two RJ45 Ethernet ports (ETH0 and ETH1):
­ 100/1000/2500 Mbps auto-negotiation RJ45 Ethernet Power over Ethernet (PoE) port
­ 10/100/1000 Mbps auto-negotiation RJ45 Ethernet port · One micro USB console port · One reset button
Remove the waterproof screw cap to access the micro USB port and the reset button. · One standard USB port to connect beacons (iBeacon) and Internet of Things (IoT)
devices Remove the waterproof cap to access the standard USB port. · Antennas: ­ Three integrated single-band 5.1 GHz ­ 5.8 GHz omnidirectional antennas ­ Four integrated dual band 2.4 GHz ­ 2.5 GHz and 5.1 GHz ­ 5.8 GHz
omnidirectional antennas · Temperature:
­ Operating temperature: -40 °C to +60 °C (-40 °F to +140 °F) ­ Storage temperature: -40 °C to +70 °C (-40 °F to +158 °F) ­ Relative humidity: 0% to 95% (non-condensing)
Table 1 AP460C, AP460S6C, AP460S12C Power profile

AP460C, AP460S6C, AP460S12C

802.3af

802.3at

2.4G radio

2x2 (14 dBM)

2x2 (18 dBM)

5G radio Sensor radio BLE

2x2 (17 dBM) 2.4G and 5G (15 dBm) Enabled

4x4 (18 dBM) 2.4G and 5G (18 dBm) Enabled

USB

No

Yes

2.5G Ethernet

Yes

Yes

1G Ethernet

No

Yes

For detailed device and radio specifications, refer to the AP460C, AP460S6C, AP460S12C Data Sheet.
Figure 1 Front views of AP460C, AP460S6C, AP460S12C

Figure 2 AP460C access point hardware components

Table 2 Hardware ports on AP460C access point Callout Description

1

PoE - Ethernet 0

2 Status light

3 Ethernet 1

4 Built-in mounting brackets

5 USB port

6 Micro USB console and reset button

7 Ground

8 Air pressure vent

Status LED
The status light, located between the two Ethernet ports, conveys operational states for system power, firmware updates, Ethernet and wireless interface activity, and major alarms.
· Steady white: The device has successfully established a Control And Provisioning of Wireless Access Points (CAPWAP) connection to ExtremeCloud IQ and is operating normally.
· Slow-blinking white: The device has a CAPWAP connection to ExtremeCloud IQ, but is operating on 802.3af power instead of 802.3at power.
· Steady amber: The device is initializing, rebooting, or is running without a CAPWAP connection.
· Slow-blinking amber: The device has no CAPWAP connection to ExtremeCloud IQ, and is operating on 802.3af power instead of 802.3at power.
· Fast-blinking amber: The device is upgrading it's IQ Engine firmware. · Dark: power is off.
AP460C, AP460S6C, AP460S12C Box Contents
Ensure that the following items are available:
Table 3 Contents of the AP460C, AP460S6C, AP460S12C Box

Quantity Item

1

Read Me card

1

An access point you have ordered (AP460C or AP460S6C or AP460S12C)

Hardware bag containing:

1

· M4 ground screw · Split washer

· Lock washer

All optional brackets and accessories are sold separately. For detailed installation instructions about all mounting procedures, refer to the ExtremeWireless AP460C, AP460S6C, AP460S12C Access Points Installation Guide in the Extreme Networks Documentation Support site.
Install the Access Point
Electrical Hazard: Only qualified personnel must perform installation procedures.

Use these instructions as guidelines for mounting and connecting the AP460C, AP460S6C, AP460S12Caccess points easily and safely.
Install the Access Point on a Vertical Pole or a Horizontal Pole
Install the access point on a vertical or horizontal pole using the built-in access point bracket, two AH-ACC-STRP-MRN accessory, which is an outdoor access point stainless steel hose strap for 3 in. to 7 in. diameter poles.
Caution: Do not install the access point in freezers.
1 Thread the cable clamp straps through the access point rear slots. 2 Position and insert the cable clamp straps around the pole.
Note: Ensure that the access point top slots face the sky and the bottom slots face the ground.
Figure 3 Pole mount strap slots on the back of the access point

Callout 1 2 3

Description Pole mount cable clamp strap insert holes in the back of the access point Top slots on the rear of the access point facing the sky Bottom slots on the rear of the access point facing the ground

3 Using a slotted screwdriver, tighten the clamp screws to a minimum torque of 14 inlbs. until the access point is securely mounted onto the pole. As an added security measure, you can thread a safety strap through one of the cable clamp slots in addition to the cable clamps. Connect the other end of the strap to a secure object.
Note: The access point LAN glands must face down to eliminate water from entering the chassis.

Install the Access Point on a Flat Surface
Install the access point on a vertical or horizontal flat surface using the AH-ACC-BKT-ASM accessory.

Before beginning the mounting procedure, insert the four M5 bolts into the holes on the rear of the access point and torque the bolts to 16 in-lbs.
Figure 4 Wall mounting accessory M5 bolt holes

Callout 1

Description M5 bolt attachment holes

Note: If you are mounting the access point horizontally, ensure that the ports are facing down to reduce the chance of water entering the chassis.
1 Using the ASM wall accessory as a template, mark and drill four mounting holes on a flat surface.
Figure 5 ASM accessory wall mounting hole markings

2 Attach the ASM accessory to the wall by using four M5 shoulder mounting screws.
Note: The best practice is to use screw-in anchors with the mounting screws on a wood surface and concrete anchors on a concrete surface.
3 Insert the M5 shoulder mounting screws into the mounting holes. 4 Torque the M5 shoulder mounting screws to 25 in-lbs. 5 Remove the two locking screws on the accessory.
Note: The access point will not go onto the accessory if the locking screws are not removed.
6 Insert the M5 bolt heads on the access point into the large end of the accessory keyholes and slide the access point down until the bolts rest in the narrow end of the keyholes.
7 Tighten the locking screws on the ASM accessory to secure the access point. 8 Ground the access point.
Ground Connection
When you install the access point on an outdoor environment, you must provide protective grounding to prevent the access point from damages and failures. Safely ground the access point using the grounding hardware. The following hardware is required for ground connection: · An access point · One M4 ground screw · One star washer · One ground terminal · One ground wire
Note: The installer must provide the ground wire.
1 Strip the insulation off one end of the ground wire and attach the stripped wire to the ring terminal. Use a 10 AWG electrical wire.
2 Attach the ground wire ring terminal to the access point using the M4 ground screw assembly with the star washer. The star washer must be in contact with both the ring terminal and the access point.
Figure 6 Ground connection on the access point

Callout 1 2 3 4 5

Description Ground terminal edge area Ground terminal 10 AWG ground wire M4 screw Star washer

3 Tighten the screw to a torque of 12 in-lbs. 4 Connect the other end of the ground wire to an appropriate earthing location.
Note: For antenna specifications and installation information, refer to the Wi-Fi 6 (802.11ax) Antenna Specifications Guide.
Install the Weatherproof Ethernet Cable Housing
Use the waterproof Ethernet cable housing to ensure a weatherproof seal for the Ethernet cable. Install the waterproof Ethernet cable housing on the cable before connecting the RJ45 cable. 1 Remove the sealing nut, claw, and the 2-part seal from the main body of the
waterproof housing. Assemble the pieces around the Ethernet cable as shown in Figure 7.
Figure 7 Weatherproof Ethernet cable housing

Callout 1 2 3 4 5

Description Sealing nut Claw Seal Ethernet connector Main body

2 Insert the Ethernet cable through the sealing nut and the claw. 3 Take the seal apart, insert the cable between the two halves, and reassemble the seal. 4 Insert the seal into the claw. 5 Insert the Ethernet connector to the main access point body and into the connector
until the locking 6 tab clicks into place.Insert the seal and the claw into the main body. 7 Screw the sealing nut onto the threaded main body. 8 Tighten it to a torque of 12 in-lbs. 9 Connect the other end of the Ethernet cable to a PoE injector or a PoE-enabled
switch. For more information about external antenna gains, removal of RJ45 cable, and power specifications, refer to the ExtremeWireless AP460C, AP460S6C, AP460S12C Access Point Installation Guide.
Professional Installation Instruction
Installation personnel
This product is designed for specific application and needs to be installed by a qualified personnel who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.
Installation procedure
Refer to the ExtremeWireless AP460C, AP460S6C, AP460S12C Access Point Installation Guide.
Warning: Select the installation position and ensure that the final output power does not exceed the limit set forth in relevant rules. The violation of the rule could lead to serious federal penalty.

Instructions d'installation professionnelle
Installation
Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
Procedure d'installation Consulter le manuel d'utilisation ExtremeWireless AP460C, AP460S6C, AP460S12C Access Point Installation Guide.
Warning: Avertissement: Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales.

Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety and to prevent damage to the equipment.
Qualified Personnel: Electrical Hazard: Only qualified personnel must perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission grounding devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes.
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Warning: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 30 cm between the radiator and your body.
Country Code selection feature to be disabled for products marketed to the US/
CANADA.
Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Japan Voluntary Control Council for Interference (VCCI) Class B

Conformitè Europëenne (CE) Information
Warning: CE co-location MPE Statement: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

Selling Countries:

AT BE BG HR CY CZ DK

EE

FI

FR DE EL HU IE

IT

LV

LT LU MT NL PL

PT RO SK SI ES SE UK

CE Marking and European Area (EEA)
Warning: This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Other Countries
Brazil
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução n°. 242/2000 e atende aos requisitos técnicos aplicados. Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Para maiores informações, consulte o site da ANATEL ­ www.anatel.gov.br
Mexico Compliance Statement
La operacion de este equipo esta sujeta a las siguientes dos condiciones 1 es posible que este equipo o dispositivo no cause interferencia perjudicial y

2 este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.
The operation of this equipment is subject to the following two conditions: 1 It is possible that this equipment or device does not cause disruptive interference and 2 This equipment or device must accept any interference, including interference that
may cause undesired operation.
Industry Canada Notice
Warning: For indoor use only. Pour une utilisation en intérieur uniquement.
This device complies with ISED's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d' ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution: The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Caution: Avertissement: les dispositifs fonctionnant dans la bande 51505250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
This radio transmitter [IC: 4141B-AP460C, AP460S6C, AP460S12C] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed in ExtremeWireless AP460C, AP460S6C, AP460S12C Access Point Installation Guide, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le présent émetteur radio [IC: 4141B-AP460C, AP460S6C, AP460S12C] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne répertoriés dans le Guide d'installation des points d'accès sans fil extrêmes AP460C, AP460S6C, AP460S12C, avec le un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Taiwan Regulatory Statement
Taiwan Maximum Permissible Exposure (MPE) Warning AP460C
AP460S6C and AP460S12C (AP460SC series)
European Waste Electrical and Electronic Equipment (WEEE) Notice
In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE): 1 The symbol above indicates that separate collection of electrical and electronic
equipment is required.

2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately.
3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.
4 It is the users' responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Environmental Compliance at [email protected].
Declaration of Conformity in Languages of the European Community

English

Hereby, Extreme Networks declares that the radio equipment type (AP460C, AP460S6C, AP460S12C) is in compliance with Directive 2014/ 53/EU. For full text of the EU Declaration of Conformity, please contact Extreme Regulatory Compliance at [email protected]

Finnish

Täten Extreme Networks vakuuttaa, että Radio laite tyyppi (AP460C, AP460S6C, AP460S12C) on direktiivin 2014/53/EU mukainen.EU vaatimustenmukaisuusvakuutuksen täydellisestä tekstistä ota yhteyttä äärimmäisiin viranomais säädöksiin osoitteessa [email protected]

Dutch

Extreme Networks verklaart hierbij dat het type radioapparatuur (AP460C, AP460S6C, AP460S12C) in overeenstemming is met richtlijn 2014/53/EU.Voor de volledige tekst van de EU-conformiteitsverklaring u contact opnemen met extreme regelgeving op [email protected]

French

Par la présente, Extreme Networks déclare que le type d'équipement radio (AP460C, AP460S6C, AP460S12C) est conforme à la directive 2014/ 53/UE.Pour le texte intégral de la Déclaration de conformité de l'UE, veuillez communiquer avec Extreme Regulatory Compliance à [email protected]

Swedish

Härmed intygar Extreme Networks att radioutrustning typ (AP460C, AP460S6C, AP460S12C) överensstämmer med direktiv 2014/53/EU.För fullständig text av EU-försäkran om överensstämmelse, vänligen kontakta Extreme regelefterlevnad på [email protected]

Danish

Herved erklærer Extreme Networks, at radioudstyrs typen (AP460C, AP460S6C, AP460S12C) er i overensstemmelse med direktiv 2014/53/ EU.For den fulde ordlyd af EU-overensstemmelseserklæringen bedes du kontakte Extreme Regulatory Compliance på [email protected]

German

Dabei erklärt Extreme Networks, dass der Funkgerätetyp (AP460C, AP460S6C, AP460S12C) mit der Richtlinie 2014/53/EU im Einklang steht.Für den vollständigen Wortlaut der EU-Konformitätserklärung wenden Sie sich bitte an extreme Regulatory Compliance unter [email protected]

Greek

  ,         (AP460C, AP460S6C, AP460S12C)     2014/53/.       ,         [email protected]

Icelandic

Hérlendis, Extreme Networks, lýsa því yfir að útvarpsbúnaðargerðin (AP460C, AP460S6C, AP460S12C) sé í samræmi við tilskipun 2014/53/ ESB.Fyrir fullan texta í ESB yfirlýsingu um samræmi, vinsamlegast hafðu samband við Extreme Reglufylgni á [email protected]

Italian

Di conseguenza, Extreme Networks dichiara che il tipo di apparecchiature radio (AP460C, AP460S6C, AP460S12C) è conforme alla direttiva 2014/ 53/EU.Per il testo integrale della Dichiarazione di conformità dell'UE, contattare Extreme Regulatory Compliance presso [email protected]

Spanish

Por la presente, Extreme Networks declara que el tipo de equipo radioeléctrico (AP460C, AP460S6C, AP460S12C) cumple con la Directiva 2014/53/UE.Para obtener el texto completo de la Declaración de conformidad de la UE, póngase en contacto con Extreme Regulatory Compliance en [email protected]

Portuguese Por este meio, a Extreme Networks declara que o tipo de equipamento de rádio (AP460C, AP460S6C, AP460S12C) está em conformidade com a Diretiva 2014/53/UE.Para obter o texto integral da Declaração de Conformidade da UE, contacte o cumprimento regulamentar extremo em [email protected]

Malti

B ' dan, netwerks estremi, jiddikjara li t-tip ta ' tagmir tar-radju (AP460C, AP460S6C, AP460S12C) huwa konformi mad-Direttiva 2014/53/UE.Gattest si tad-dikjarazzjoni ta ' konformità tal-UE, jekk jogbok ikkuntattja lill-konformità regolatorja [email protected]

ExtremeWirelessTM Access Points
Quick Reference
AP460C, AP460S6C, AP460S12C
Notice Copyright © 2021 Extreme Networks, Inc. All Rights Reserved.
Legal Notices Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.
Trademarks Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see: www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, and Support For product support, including Documentation and Installation Videos, visit: www.extremenetworks.com/documentation
P/N 9036949-00 Rev AA


Adobe PDF Library 15.0

Search Any Device: