Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 4 Pages, 2.18MB
Document DEVICE REPORTFLC3 ROhousing IS0755 0id+ 3.5" round housing FLC3D | FLC3W LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING. ALL GRID LUMINAIRES MUST BE SECURED TO STRUCTURE ABOVE. - - non emergency thermally protected, non-ic optional bar hangers sold separately key power off power on FLC3D | FLC3W - emergency remote test switch, non-ic ic/cp attention level see additional instructions WALL WASH ORIENTATION WALL FLC3D | FLC3W FLC3D | FLC3W KEEP SHADED AREA FREE FROM OBSTRUCTION ABOVE CEILING SHORT CONE DNS SUPER SHORT CONE DSS 2.64" .50" 10.61" 10.61" TALL CONE 3.16" DNT .50" FOR ASTM E-283 AIR-TIGHT COMPLIANCE, SEAL IC HOUSING/ RO TRIM WITH SILICONE CAULKING BETWEEN THE EDGE OF THE COLLAR AND CEILING MATERIAL. SEAL ALL ADDITIONAL HOLES IN HOUSING WITH ALUMINUM TAPE. IS0761 REV. B Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 4 1 4 1/8" ceiling cutout GRID - 1/2" CONDUIT & CLIP (BY OTHERS) 2 X2 3 GRID - BAR HANGERS (SOLD SEPARATELY) 2 x2 3 4b multiple luminaires only 4 x4 4a x4 IS0761 REV. B Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 4 DRYWALL - BAR HANGERS WOOD STUDS 2a x4 2b x4 METAL STUDS 3 x4 4 5 minimum ceiling thickness: 1/2" maximum ceiling thickness: 1-1/2" EMERGENCY - REMOTE TEST SWITCH 1 2 Ø 4.125" make electrical connections ABOVE CEILING ACCESS REQUIRED 3 7.304" ± 0.25" 141 release test switch from bracket prior to installation 5.246 ± 0.58" 5 3.187 ± 0.58" Ø 0.75" 6 IS0761 REV. B adjust test switch until canopy is flush with ceiling BATTERY UNIT CONNECTOR INSIDE Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 4 171 SEE BATTERY MANUFACTURER INSTRUCTIONS DRIVER SERVICE EM- MOUNTING HEIGHT DO NOT MATE BATTERY UNIT CONNECTOR UNTIL INSTALLATION IS COMPLETE AND A.C. POWER IS SUPPLIED SEE BATTERY MANUFACTURER INSTRUCTIONS emergency maximum mounting height: DOWNLIGHT: 21.4' WALL WASH: 16.1' 1 2 TO PREVENT ELECTRICAL SHOCK, DISCONNECT ELECTRICAL SUPPLY BEFORE SERVICING Contractor is responsible for adequately reinforcing walls and/or ceilings to support fixture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS0761 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 4Adobe PDF Library 16.0.7 Adobe InDesign 17.3 (Macintosh)