user manual

Shenzhen Jos Technology Co., Ltd. 405 Universal garage door opener 2A5Z8-405 2A5Z8405 405

Instruction Manual for JOSLMMAX models including: 2A5Z8-405, 2A5Z8405, 405, Universal Garage Door Opener, Garage Door Opener, Door Opener, Opener

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 1 Pages, 322.94KB

Document DEVICE REPORTGetApplicationAttachment.html?id=8365013 
PREMIUM  INSTRUCTIONS REMOTE
5-BUTTON PREMIUM REMOTE TRANSMITTER
PROGRAMMING AND REMOTE TRANSMITTER OVERVIEW A ll remote transmitters must be programmed before they will operate the Gate Opener System so that the safety and security of your system is maintained

LED LIGHT
e 0 =Off  On=Flash,ng

©



Acti,ates Gate lo, Gat,2

LEARN BUTTON
To P,ogcam Addooal Remote

REMOTE A (TRAINING)
T r a n s E 1  t t  n g
1 *
g R e c g l n
REMOTE B (LEARNING)

NOTE REMOTES A & 8 MUST BE TOUCHING AND ORIENTED AS SHOWN TO PROGRAM REMOTE 8 FROM REMOTE A

2

 Pess & hold LEARN XMTR

button

on gate system

I It=otroller LED is

. controller :-0·

Gate alarm sounds and LEARN XMTR LED on system controller
I stay · =On
I:;:r alarm beeps or gate

I Places ate controller into Learn Remote mode for 10 seconds. NOTE-The gate system
controlrer will exit the Learn Remote mode afte10 seconds and return to normal opeation if there IS no valid remote transmitter signal ece,ved
I Programs this button into memoy

3 4 ILNEoAaRlNarmXMsoTuRnLdsE,D
on main controller is 0 =Off LED on remote is Q =Off
2 3

 Release the. or

LEARN XMTR LED go es O=Off

 I Pess and release the.or Transm,tter LED blinks on when

utton

button ,s depressed

The new transm;tter's ID has been saved ;nto the m emory of the ma;n system controller.

Test the transmitter button youust program_med. LED on transmitter turns on only when

but ton is depressed to indicate it is of this r emote button will cycle the

tgraatnesmas,tfto,nllogwssi:gOnaPl Etorf-aSteTOcoPn-trCoLllOerS. EE-aSchT

gPe-ss

OPEN. The transmitting

LED time

wisiallpbperoxaismhiantgelrya1Odlsyewcohnednstthoestarvaensbmatittteeryr

is transmitting. life

Maximum

ADD AN ADDITIONAL REMOTE TRANSMITTER TO CONTROL THE GATE

 I hs'd the .on
(Learning) for at least 3 seconds Remote LED is · =On or untilthe LEDgoes e =On

I Press & hold. 
on Remote A, the Teach,ng Remote.

LEDs.on both Teaching and
 Learning Remote
ae =Flashing

 i Press &release. r

n

Remote B, theLearning Remote

Remote LED goes O=Off

This process assumes that Remote A CTeach,ng Remote) is ALREADYcapable of contoll,ng the gate. This puts Remote B (Learning Remote) into Learning Mode Remote A (Teach,ng Remote) IS in Teach Mode, and Remote B (Learning Remote) IS in Learn Mode. Indicates that the Leaning Remote button (Remote B) pessed in this step is now programmed to operate the same gate as the Teach,ngRemote(RemoteA).

CLONE/ COPY BUTTON 1'S ID TO BUTTON 2'S (BUTTON 1 ALREADY CONTROLS THE GATE)

Pess & hold LEARN · button on Remote fo AT LEAST 3 seconds until the LED turns on

LED on Remote stays e=On

Places emote tansmitte into Learning mode

2

Release the LEARN Button ILED remains. =On

Remote is in Learning Mode

3

Press and Release Button 1

 LED should start (2shes a sec)

=Flashing Remote is sending button l's ID

4

Press and Release Button 2 LED should go O=Off

Button l's ID is accepted by button 2. Both buttons should now work the same gate.

CLONE/ COPY BUTTON 2'5 ID TO BUTTON 1'5 (BUTTON 2 ALREADY CONTROLS THE GATE)

Press & hold LEARN · button on Remote fo AT LEAST 3 seconds until the LED turns on

LED on Remote stays e=On

Places remote Iansmitte into Learning mode

2

Release the LEARN Button LED remains. =On

Remote is in Learning Mode

3

Press and Release Button 2

 LED should start
(2ashes a sec)

=Flashing Remote is sending button 2's ID

4

Press and Release Button 1 LED should go O=Off

Button 2's ID ;s accepted by button 1. Both buttons should now work the same gate

(HOLD OPEN) FUNCTION
Enabling this Mode through a remote transmitter sends a command/message to the gate controller to turn Mode function On or Off. The gate opener system will remain in Mode until the gate controller receives a signal to be disabled or the power button on the Control Box is cycled to the off poson. Once Mode has been disabled, all functions such as AUTOCLOSE will return to their previous operation

Tells the Remote tansmitte that you ae about to enter into Mode

2 IReem=oOtenLED is

This places the main system contoiler into Mde until you disable it or if you cycle the ON/_Off

switch on already at

the the

yi'mteit.syAsltl

em control box. Gate w,11 op remotes and other controls

en and emain open such as keypads are

at the full op ignored (but

en pos,t1on ,f not are acknowledged

with two beeps from gate system alarm) once the gate is at the open l,m,t

TO DISABLE MODE

 Press & hold on Remote LED on Remote goes
I unt;I the LED goes. =On e=On
Press & release.or . LED goes O=Off on R emote

T ells th e Remot e transmitt er that you are about to exit Mode
I This disables Mode on the main system controller and enables AUTOCLOSEt was peviously
enabled. Gate will close automatically if AUTOCLOSE os enabled

GATE SYSTEM CONTROLLER DIAGNOSTIC MODE
Diagnostic Mode function sends a command/message to the gate controller to activate diagnostics indicators (LEDs and/or alarm codes) on the gate controller. Refer to the gate opener manual for specific details about the indicators. To conserve the battery powe, the main controller indicators (LEDs and alarm) are turned off when gate is idled fo moe than 60 seconds (except foUL-325 re9uirement for entrapment protection). Enabling Diagnostic Mode will turn these indicators on for 5 minutes without the need to opeate the gate.

Pressing the Test button on the remote transmitter indicates the status of the gate system controller battery. It does not indicate the status of the CR2032 battery inside of the remote itself

l I I Press & release

LED goes O=Off

on Remote

GENERATING A NEW TRANSMITTING KEY CODE

Tells the Remote transm;tter that you are about to enter ;nto Test Mode The gate system controller wdl use the gate alarm to ,ndicate the gate status 1 Beep= Battery is good 2 Beeps= Battery is low

3 IReem=oOtenLED is

i Press &hold .AND
simultaneously for10 seconds on Remote until the LED go es e=On

LED on Remote go es e=On

 Release & AND

 I I Press & release . r

LED goes O=Off

on Remote

Tells the emote transmitter (Remote 8) that you ae going to geneate a new code. Step 2 & 3 must be completed within 5 seconds whole the LED os lot The remote button pressed ;n th;, step ;, now generat;ng a new code

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Related FCC IDs:

Search Any Device: