Hank Yan
Test report
Dongguan Wangpeng Hardware Products Co., Ltd. A18 Portable Wireless Charger For Apple Watch 2BOJS-A18 2BOJSA18 a18
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 25 Pages, 1.88MB
Document DEVICE REPORTGetApplicationAttachment.html?id=8197053Test Report Report No. Date of issue Applicant Product Model(s) FCC ID : MTi250321005-0102E1 : 2025-04-02 : Dongguan Wangpeng Hardware Products Co., Ltd : Portable Wireless Charger For Apple Watch : A18 : 2BOJS-A18 Shenzhen Microtest Co., Ltd. Tel:0755-88850135-1439 Mobile: 131-4343-1439Wechat same number Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 1 of 25 TEST REPORT Report No.: MTi250321005-0102E1 Table of contents 1 General Description ..................................................................................................................... 4 1.1 Description of the EUT ........................................................................................................ 4 1.2 Description of test modes.................................................................................................... 4 1.3 Environmental Conditions ................................................................................................... 5 1.4 Description of support units ................................................................................................ 5 1.5 Measurement uncertainty.................................................................................................... 5 2 Summary of Test Result .............................................................................................................. 6 3 Test Facilities and accreditations ............................................................................................... 7 3.1 Test laboratory..................................................................................................................... 7 4 List of test equipment .................................................................................................................. 8 5 Evaluation Results (Evaluation) ................................................................................................. 9 5.1 Antenna requirement........................................................................................................... 9 6 Radio Spectrum Matter Test Results (RF) ............................................................................... 10 6.1 Conducted Emission at AC power line.............................................................................. 10 6.2 20dB Occupied Bandwidth................................................................................................ 13 6.3 Emissions in frequency bands (below 30MHz)................................................................. 16 6.4 Emissions in frequency bands (30MHz - 1GHz)............................................................... 19 Photographs of the test setup ......................................................................................................... 23 Photographs of the EUT ................................................................................................................... 24 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 2 of 25 TEST REPORT Report No.: MTi250321005-0102E1 Test Result Certification Applicant Dongguan Wangpeng Hardware Products Co., Ltd Applicant Address 102, 1st Floor, Building A3, Qihua Industrial Zone, Fenggang Town, Dongguan City Manufacturer Dongguan Wangpeng Hardware Products Co., Ltd Manufacturer Address 102, 1st Floor, Building A3, Qihua Industrial Zone, Fenggang Town, Dongguan City Product description Product name Portable Wireless Charger For Apple Watch Trademark ZIKUREL, iWpeng Model name A18 Series Model(s) N/A Standards 47 CFR Part 15C Test Method ANSI C63.10-2013 Testing Information Date of test 2025-03-24 to 2025-03-26 Test result Pass Prepared by: James Qin Reviewed by: David Lee Approved by: Lewis Lian Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 3 of 25 TEST REPORT 1 General Description Report No.: MTi250321005-0102E1 1.1 Description of the EUT Product name: Portable Wireless Charger For Apple Watch Model name: A18 Series Model(s): N/A Model difference: Electrical rating: Accessories: Hardware version: N/A Input: DC 5V/ 2A Output: 3W Capacity: 2000mAh(3.7V/ 7.4Wh) Cable: Type-c to Type-c cable: 100cm A08-D Software version: 0D58 Test sample(s) number: MTi250321005-01-R001 RF specification Operating frequency range: Modulation type: 300-360kHz ASK 1.2 Description of test modes No. Emission test modes Mode1 Wireless output Watch(3W) Mode2 stand by Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 4 of 25 TEST REPORT Report No.: MTi250321005-0102E1 1.3 Environmental Conditions During the measurement the environmental conditions were within the listed ranges: Temperature: Humidity: Atmospheric pressure: 15°C ~ 35°C 20% RH ~ 75% RH 98 kPa ~ 101 kPa 1.4 Description of support units Support equipment list Description HUAWEI QUICK CHARGE Watch Model HW-200200ZP1 iWatch SE Serial No. JN67LSN7N03451 FH7PP6BAG91J6 Manufacturer HUAWEI Apple Support cable list Description Length (m) From To / / / / 1.5 Measurement uncertainty Measurement Uncertainty Conducted emissions (AMN 150kHz~30MHz) Occupied channel bandwidth Radiated spurious emissions (9kHz~30MHz) Radiated spurious emissions (30MHz~1GHz) Temperature Humidity ±3.1dB ±3 % ±4.3dB ±4.7dB ±1 °C ± 5 % This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 5 of 25 TEST REPORT 2 Summary of Test Result Report No.: MTi250321005-0102E1 No. Item 1 Antenna requirement 2 Conducted Emission at AC power line Standard 47 CFR Part 15C 47 CFR Part 15C 3 20dB Occupied Bandwidth 47 CFR Part 15C 4 Emissions in frequency bands (below 30MHz) 5 Emissions in frequency bands (30MHz - 1GHz) 47 CFR Part 15C 47 CFR Part 15C Requirement 47 CFR Part 15.203 47 CFR Part 15.207(a) 47 CFR Part 15.215(c) 47 CFR Part 15.209 Result Pass Pass Pass Pass 47 CFR Part 15.209 Pass Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 6 of 25 TEST REPORT 3 Test Facilities and accreditations Report No.: MTi250321005-0102E1 3.1 Test laboratory Test laboratory: Test site location: Telephone: Shenzhen Microtest Co., Ltd. 101, No.7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China (86-755)88850135 Fax: (86-755)88850136 CNAS Registration No.: CNAS L5868 FCC Registration No.: 448573 IC Registration No.: 21760 CABID: CN0093 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 7 of 25 TEST REPORT 4 List of test equipment Report No.: MTi250321005-0102E1 No. Equipment Manufacturer Model Serial No. Cal. date Cal. Due Conducted Emission at AC power line 1 EMI Test Receiver Rohde&schwarz ESCI3 101368 2025-03- 2026-03- 13 12 2 Artificial mains network Schwarzbeck NSLK 8127 183 2025-03- 2026-03- 18 17 3 Artificial Mains Network Rohde & Schwarz ESH2-Z5 100263 2025-03- 2026-03- 18 17 20dB Occupied Bandwidth 1 Wideband Radio Communication Tester Rohde&schwarz 2 ESG Series Analog Ssignal Generator Agilent 3 PXA Signal Analyzer Agilent 4 Synthesized Sweeper Agilent 5 MXA Signal Analyzer Agilent 6 RF Control Unit Tonscend 7 Band Reject Filter Group 8 ESG Vector Signal Generator 9 DC Power Supply Tonscend Agilent Agilent CMW500 E4421B N9030A 83752A N9020A JS0806-1 JS0806-F N5182A E3632A 149155 GB400512 40 MY513502 96 3610A019 57 MY501434 83 19D80601 52 19D80601 60 MY501437 62 MY400276 95 2025-0318 2025-0314 2025-0314 2025-0318 2025-0318 2025-0318 2025-0318 2025-0314 2025-0318 2026-0317 2026-0313 2026-0313 2026-0317 2026-0317 2026-0317 2026-0317 2026-0313 2026-0317 Emissions in frequency bands (below 30MHz) 1 EMI Test Receiver Rohde&schwarz ESCI7 101166 2025-03- 2026-03- 14 13 2 Active Loop Antenna Schwarzbeck FMZB 1519 B 00066 2024-03- 2026-03- 23 22 3 Amplifier Hewlett-Packard 8447F 3113A0618 2025-03- 2026-03- 4 18 17 Emissions in frequency bands (30MHz - 1GHz) 1 EMI Test Receiver Rohde&schwarz ESCI7 101166 2025-03- 2026-03- 14 13 2 TRILOG Broadband Antenna schwarabeck VULB 9163 9163-1338 2023-06-11 2025-0610 3 Active Loop Antenna Schwarzbeck FMZB 1519 B 00066 2024-03- 2026-03- 23 22 4 Amplifier Hewlett-Packard 8447F 3113A0618 2025-03- 2026-03- 4 18 17 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 8 of 25 TEST REPORT 5 Evaluation Results (Evaluation) Report No.: MTi250321005-0102E1 5.1 Antenna requirement Test Requirement: Refer to 47 CFR Part 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 5.1.1 Conclusion: The antenna of the EUT is permanently attached. The EUT complies with the requirement of FCC PART 15.203. Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 9 of 25 TEST REPORT Report No.: MTi250321005-0102E1 6 Radio Spectrum Matter Test Results (RF) 6.1 Conducted Emission at AC power line Test Requirement: Test Limit: Test Method: Procedure: Except as shown in paragraphs (b)and (c)of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table, as measured using a 50 H/50 ohms line impedance stabilization network (LISN). Frequency of emission (MHz) 0.15-0.5 0.5-5 5-30 Conducted limit (dBV) Quasi-peak Average 66 to 56* 56 to 46* 56 46 60 50 *Decreases with the logarithm of the frequency. ANSI C63.10-2013 section 6.2 Refer to ANSI C63.10-2013 section 6.2, standard test method for ac power-line conducted emissions from unlicensed wireless devices 6.1.1 E.U.T. Operation: Operating Environment: Temperature: 23.8 °C Humidity: 62 % Atmospheric Pressure: 100 kPa Pre test mode: Mode1, Mode2 Final test mode: All of the listed pre-test mode were tested, only the data of the worst mode (Mode1) is recorded in the report 6.1.2 Test Setup Diagram: Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 10 of 25 6.1.3 Test Data: Mode1 / Line: Line TEST REPORT Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 11 of 25 Mode1 / Line: Neutral TEST REPORT Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 12 of 25 TEST REPORT 6.2 20dB Occupied Bandwidth Report No.: MTi250321005-0102E1 Test Requirement: Test Limit: 47 CFR Part 15.215(c) Refer to 47 CFR 15.215(c), intentional radiators operating under the alternative provisions to the general emission limits, as contained in §§ 15.217 through 15.257 and in subpart E of this part, must be designed to ensure that the 20 dB bandwidth of the emission, or whatever bandwidth may otherwise be specified in the specific rule section under which the equipment operates, is contained within the frequency band designated in the rule section under which the equipment is operated. Test Method: Procedure: ANSI C63.10-2013, section 6.9.2 a) The spectrum analyzer center frequency is set to the nominal EUT channel center frequency. The span range for the EMI receiver or spectrum analyzer shall be between two times and five times the OBW. b) The nominal IF filter bandwidth (3 dB RBW) shall be in the range of 1% to 5% of the OBW and video bandwidth (VBW) shall be approximately three times RBW, unless otherwise specified by the applicable requirement. c) Set the reference level of the instrument as required, keeping the signal from exceeding the maximum input mixer level for linear operation. In general, the peak of the spectral envelope shall be more than [10 log (OBW/RBW)] below the reference level. Specific guidance is given in 4.1.5.2. d) Steps a) through c) might require iteration to adjust within the specified tolerances. e) The dynamic range of the instrument at the selected RBW shall be more than 10 dB below the target "-xx dB down" requirement; that is, if the requirement calls for measuring the -20 dB OBW, the instrument noise floor at the selected RBW shall be at least 30 dB below the reference value. f) Set detection mode to peak and trace mode to max hold. g) Determine the reference value: Set the EUT to transmit an unmodulated carrier or modulated signal, as applicable. Allow the trace to stabilize. Set the spectrum analyzer marker to the highest level of the displayed trace (this is the reference value). h) Determine the "-xx dB down amplitude" using [(reference value) - xx]. Alternatively, this calculation may be made by using the markerdelta function of the instrument. i) If the reference value is determined by an unmodulated carrier, then turn the EUT modulation ON, and either clear the existing trace or start a new trace on the spectrum analyzer and allow the new trace to stabilize. Otherwise, the trace from step g) shall be used for step j). j) Place two markers, one at the lowest frequency and the other at the highest frequency of the envelope of the spectral display, such that each marker is at or slightly below the "-xx dB down amplitude" determined in step h). If a marker is below this "-xx dB down amplitude" value, then it shall be as close as possible to this value. The occupied bandwidth is the frequency difference between the two markers. Alternatively, set a marker at the lowest frequency of the envelope of the spectral display, such that the marker is at or slightly below the "-xx dB down amplitude" determined in step h). Reset the Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 13 of 25 TEST REPORT Report No.: MTi250321005-0102E1 marker-delta function and move the marker to the other side of the emission until the delta marker amplitude is at the same level as the reference marker amplitude. The marker-delta frequency reading at this point is the specified emission bandwidth. k) The occupied bandwidth shall be reported by providing plot(s) of the measuring instrument display; the plot axes and the scale units per division shall be clearly labeled. Tabular data may be reported in addition to the plot(s). 6.2.1 E.U.T. Operation: Operating Environment: Temperature: 25.3 °C Humidity: 56 % Atmospheric Pressure: 101 kPa Pre test mode: Final test mode: Mode1, Mode2 All of the listed pre-test mode were tested, only the data of the worst mode (Mode1) is recorded in the report 6.2.2 Test Setup Diagram: Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 14 of 25 6.2.3 Test Data: TEST REPORT Report No.: MTi250321005-0102E1 Note: Because the measured signal is CW-like, adjusting the RBW per C63.10 would not be practical since measurement bandwidth will always follow the RBW. The RBW is set to 300 Hz to perform the occupied bandwidth test. Frequency kHz 329.05 20 dB occupied bandwidth Hz 966 99% occupied bandwidth Hz 881 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 15 of 25 TEST REPORT 6.3 Emissions in frequency bands (below 30MHz) Report No.: MTi250321005-0102E1 Test Requirement: Test Limit: Test Method: Procedure: 47 CFR Part 15.209 Frequency (MHz) 0.009-0.490 0.490-1.705 1.705-30.0 30-88 88-216 216-960 Above 960 Field strength (microvolts/meter) 2400/F(kHz) 24000/F(kHz) 30 100 ** 150 ** 200 ** 500 Measuremen t distance (meters) 300 30 30 3 3 3 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470806 MHz. However, operation within these frequency bands is permitted under other sections of this part, e.g., §§ 15.231 and 15.241. In the emission table above, the tighter limit applies at the band edges. The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 990 kHz, 110490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. As shown in § 15.35(b), for frequencies above 1000 MHz, the field strength limits in paragraphs (a)and (b)of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b)of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. ANSI C63.10-2013 section 6.4 ANSI C63.10-2013 section 6.4 6.3.1 E.U.T. Operation: Operating Environment: Temperature: 22.5 °C Humidity: 58 % Atmospheric Pressure: 101 kPa Pre test mode: Final test mode: Mode1, Mode2 All of the listed pre-test mode were tested, only the data of the worst mode (Mode1) is recorded in the report 6.3.2 Test Setup Diagram: Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 16 of 25 TEST REPORT 6.3.3 Test Data: Mode1 / EUT direction: X axis Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 17 of 25 TEST REPORT Mode1 / EUT direction: X axis Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 18 of 25 TEST REPORT 6.4 Emissions in frequency bands (30MHz - 1GHz) Report No.: MTi250321005-0102E1 Test Requirement: Test Limit: Test Method: Procedure: 47 CFR Part 15.209 Frequency (MHz) 0.009-0.490 0.490-1.705 1.705-30.0 30-88 88-216 216-960 Above 960 Field strength (microvolts/meter) 2400/F(kHz) 24000/F(kHz) 30 100 ** 150 ** 200 ** 500 Measuremen t distance (meters) 300 30 30 3 3 3 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470806 MHz. However, operation within these frequency bands is permitted under other sections of this part, e.g., §§ 15.231 and 15.241. In the emission table above, the tighter limit applies at the band edges. The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 990 kHz, 110490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. As shown in § 15.35(b), for frequencies above 1000 MHz, the field strength limits in paragraphs (a)and (b)of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b)of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. ANSI C63.10-2013 section 6.5 ANSI C63.10-2013 section 6.5 6.4.1 E.U.T. Operation: Operating Environment: Temperature: 22.5 °C Humidity: 58 % Atmospheric Pressure: 101 kPa Pre test mode: Mode1, Mode2 Final test mode: All of the listed pre-test mode were tested, only the data of the worst mode (Mode1) is recorded in the report Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 19 of 25 6.4.2 Test Setup Diagram: TEST REPORT Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 20 of 25 TEST REPORT 6.4.3 Test Data: Mode1 / Polarization: Horizontal Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 21 of 25 Mode1 / Polarization: Vertical TEST REPORT Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 22 of 25 TEST REPORT Photographs of the test setup Refer to Appendix - Test Setup Photos Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 23 of 25 TEST REPORT Photographs of the EUT Refer to Appendix - EUT Photos Report No.: MTi250321005-0102E1 Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 24 of 25 TEST REPORT Report No.: MTi250321005-0102E1 Statement 1. This report is invalid without the seal and signature of the laboratory. 2. The test results of this report are only responsible for the samples submitted.Client shall be responsible for representativeness of the sample and authenticity of the material. 3. The report shall not be partially reproduced without the written consent of the Laboratory. 4. This report is invalid if transferred, altered or tampered with in any form without authorization. 5. The observations or tests with special mark fall outside the scope of accreditation, and are only used for purpose of commission, research, training, internal quality control etc. 6. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. ****** END OF REPORT ****** Tel: 0755-88850135-1439 Mobile: 131-4343-1439 (Wechat same number) Web: http://www.mtitest.cn E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong,China Q/MTI-QP-12-FE038 Ver./Rev.A1 Page 25 of 25
Related FCC IDs:
- 2BOJS-A18 - Dongguan Wangpeng Hardware Products Co., Ltd. Portable Wireless Charger For Apple Watch [-A18] Microsoft Word 2016