Built-in U-shaped Micro-photosensor PM-64 Series INSTRUCTION MANUAL

MJEC-PM64 No.0055-49V

Panasonic Industrial Devices SUNX Co., Ltd.

Built-in U-shaped Micro-photosensor PM-64 Series ...

Thank you very much for purchasing Panasonic products. Read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product.

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 1 Pages, 838.17KB

Document DEVICE REPORTmn pm 64 instruction pidsx en
INSTRUCTION MANUAL
Built-in U-shaped Micro-photosensor PM-64 Series
MJEC-PM64 No.0055-49V
Thank you very much for purchasing Panasonic products. Read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference.
WARNING
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country.
Since protection circuit against output short-circuit or reverse polarity connection is not incorporated, make sure to wire correctly. Also, ensure to insulate the unused output wire. Take care that wrong wiring will damage the sensor.

1 I/O CIRCUIT DIAGRAM
NPN output type Color code of optional connector attached cable

(Brown) +V

Main circuit

Internal circuit

(Black) Output 1

Load Load +

(White) Output 2 50mA max.

-

5 to 24V DC ±10%

(Blue) 0V

50mA max.

Users' circuit

* Output operation Output 1: Light-ON Output 2: Dark-ON

PNP output type Color code of optional connector attached cable

Main circuit

(Brown) +V

50mA max.

(Black) Output 1 50mA max.

+ 5 to 24V DC

(White) Output 2 Load Load - ±10%

Internal circuit

(Blue) 0V Users' circuit

* Output operation Output 1: Light-ON Output 2: Dark-ON

Note: PNP output type is not available for the PM-T64W type.

2 CAUTIONS
This product has been developed / produced for industrial use only.
Since the sensor is intended for use inside machines, no special countermeasures have been taken against extraneous light. Please take care that extraneous light is not directly incident on the beam receiving section.
If the sensor is used in a place having excessive dust, periodically clean the emitting and receiving sections with a dry, soft cloth.
Do not use during the initial transient time (50ms) after the power supply is switched on.

Cable extension is possible up to an overall length of 100m with a 0.3mm2, or more, cable. However, since

a voltage drop shall occur due to the cable

extension, ensure that the power supply voltage at

the end of the cable attached to the sensor or at the

sensor terminals is within the rating.

Connector attached cable

Overall length: 100m

+V

Extension cable

Output

+

0V

-

Supply voltage: 4.5V or more

5 to 24V DC ±10%

But, when the overall Wire conductor

Overall cable

cable length, including the cable attached to the sensor, is as given below, there is no need

cross-section area 0.08 to 0.1mm2 0.2mm2 0.3mm2

length Up to 5m Up to 10m Up to 20m

to confirm the voltage.

If there is a large surge generating equipment, such

as, motor, solenoid, electromagnetic valve, etc., in

the vicinity of the micro-photosensor, use a surge

absorber on that equipment. Further, do not run the

sensor cables along power lines and use a capacitor

between +V and 0V, if required. Use the sensor after

confirming that the surge has been eliminated.

In case the sensor is fixed

Screw

M3

with screws, strictly observe Tightening torque 0.5Nm or less

the conditions described in the right diagram.

Washer

6mm (small diameter type)

Note: If the product is used at an ambient temperature of 50 or

more, make sure to mount it on a metallic body.

3 WIRING
Connection method
 Insert the cable with connector CN-14A-C in the connector part of this product as shown in the right figure.
<Connector pin position>

Projection
CN-14A-C <Mating connector> Housing: PAP-04V-S
Manufactured by J.S.T. MFG CO., LTD.

1234

Connector pin No. 1

2

3

4

Terminal designation +V Output 1 Output 2 0V

Disconnection method

 Pressing the projection of the cable with connector, pull out the connector.
Note: Take care that if the cable is pulled out without pressing the projection, the cable may break.

4 INTENDED PRODUCTS FOR CE MARKING
 The models listed under "Catalogue" come with CE Marking. As for all other models, please contact our office.
 Economic operators' information in EU is as follows: <Importer> Panasonic Electric Works Europe AG Rudolf-Diesel-Ring2 , D-83607 Holzkirchen, Germany <Contact for CE> Panasonic Marketing Europe GmbH Panasonic Testing Center Winsbergring 15, 22525 Hamburg, Germany

http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Office) 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-568-33-7861 FAX: +81-568-33-8591
For sales network, please visit our website.
© Panasonic Industrial Devices SUNX Co., Ltd. 2016 PRINTED IN JAPAN


Adobe PDF library 10.01

Search Any Device: