English
Dolphin WAVE 30 Complete Manual & Troubleshooting | Maytronics
Dolphin Aquatight RX 6 Complete Manual & Troubleshooting | Maytronics
Instruction Manual for maytronics models including: Dolphin WAVE 30, Commercial Pool Cleaner Robot, Pool Cleaner Robot, Commercial Pool Cleaner, Pool Cleaner, Cleaner Robot, Cleaner
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 14 Pages, 12.33MB
Document DEVICE REPORT8152240 Graphics REV00Dolphin Wave 75 Pool Cleaner EN Operating Instructions 8152240 EN Robotic Pool Cleaner Dolphin Wave 75 Operating Instructions Contents 1. INTRODUCTION .............................................................................3 2. SPECIFICATIONS ............................................................................3 3. WARNINGS AND CAUTIONS ........................................................3 3.1 Warnings .................................................................................3 3.2 Cautions..................................................................................3 4. POOL CLEANER PARTS..................................................................4 5. USING THE POOL CLEANER.........................................................5 5.1 Setup.......................................................................................5 5.2 Putting the Pool Cleaner into the pool ................................5 5.3 Removing the Pool Cleaner from the pool..........................6 5.4 Maintenance...........................................................................6 5.5 Off-season storage ................................................................7 6. POWER SUPPLY ..............................................................................8 7. REMOTE CONTROL UNIT ............................................................9 CADDY ASSEMBLY .............................................................................11 2 Dolphin Wave 75 Pool Cleaner | Operating Instructions 1 Robotic Pool Cleaner Dolphin Wave 75 Operating Instructions 1. INTRODUCTION Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions and all-surface climbing brush enhance maximum pool hygiene. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting performance and easy maintenance. 2. SPECIFICATIONS Motor protection: IP 68 Minimum depth: 0.4 m (1.33 ft) Maximum depth: 5 m (16.4 ft) 3. WARNINGS AND CAUTIONS 3.1 Warnings CAUTION · Use the originally supplied power supply only · Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI) · Keep the power supply out of standing water · Position the power supply at least 3.5 m (12 ft) away from the edge of the pool · Do not enter the pool while the pool cleaner is working · Unplug the power supply before servicing · Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. 3.2 Cautions When not in use store the Pool Cleaner on the Caddy in a shaded area. Use the Pool Cleaner in the following water conditions only: Chlorine pH Temperature NaCl 4 ppm max. 7.0 - 7.8 6°C - 35°C (43°F - 95°F) 5000 ppm max. 3 Dolphin Wave 75 Pool Cleaner | Operating Instructions 4. POOL CLEANER PARTS Robotic Pool Cleaner Model Dolphin Wave 75 Brushes Remote control unit Combined Brush All surface climbing brush ideal for most pool surfaces Optional Brushes Power supply unit PVC Brush For concrete, PVC, fiberglass and liner. Wonder Brush For smooth ceramics. <30 VDC; IP 54 Filtration Bottom lid and filter Bag 4 Dolphin Wave 75 Pool Cleaner | Operating Instructions 5. USING THE POOL CLEANER 5.1 Set Up Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up with the groove in the socket on the power supply and turning clockwise (2). GFI/ELI 40°C Max 104°F Max <30 VDC; IP 54 <30 VDC; IP 54 3.5 m (12 ft) 5.2 Putting the Pool Cleaner into the pool If Wonder brush/ Wonder rings are dry, soak them in water until soft. °° °° Shake the robot from side to side or turn it upside down to release trapped air. Let it sink to the pool floor. Turn the power supply ON. The Pool Cleaner will now operate until it has reached the end of the cleaning cycle. ON <30 VDC; IP 54 5 Dolphin Wave 75 Pool Cleaner | Operating Instructions 5.3 Removing the Pool Cleaner from the pool The robot will perform automatic shut-off at the end of the cleaning cycle. Turn OFF and unplug the power supply. CAUTION OFF <30 VDC; IP 54 B A C Using the floating cable, bring the Pool Cleaner to the pool's edge. Using the handle remove the Pool Cleaner from the pool. DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE. CAUTION 5.4 Maintenance Filter bag Clean the filter bag with a hose. Periodically clean the brushes with a hose. It is recommended to periodically wash the filter bag in a washing machine. Use gentle cycle program. 6 Dolphin Wave 75 Pool Cleaner | Operating Instructions Cleaning the impeller Unplug the power supply. If you notice debris trapped in the impeller open the impeller and remove the debris. Ph Ph A No. 2 B Cable To remove the kinks, stretch the cable out completely and let it sit for at least a day in the sun. 5.5 Off-season storage If the pool cleaner will not be in use for an extended period, perform the following storage steps: · Make sure that no water is left in the pool cleaner. · Thoroughly clean the filter bag and insert in place. · Roll up the cable so that it has no kinks and place on the Caddy. · Store the pool cleaner upright on the Caddy in a protected area out of direct sun/rain/frost at a temperature of between 5°C - 45°C (41°F - 113°F). 7 Dolphin Wave 75 Pool Cleaner | Operating Instructions 6. POWER SUPPLY Digital "Switch-Mode" Power Supply with full filter bag and delay indicator. · Input - 100 VAC 250 VAC · 50 Hz 60 Hz <30 VDC; IP 54 · 180 W · Output - <30 VDC · IP 54 Delay indicator Full filter bag indicator <30 VDC; IP 54 On/Off switch Reset button Full filter bag indicator and Reset button The power supply is equipped with a filter bag status indicator. The red LED indicates two filter conditions. · When blinking - The filter is partially blocked. · When lighted - The filter is blocked and must be emptied and cleaned. If the LED does not turn off after the filter bag had been emptied and cleaned, press the RESET button while the robot is working. Delay indicator The power supply is equipped with a Delay indicator that indicates if the Delay option is activated (through the remote control unit). 8 Dolphin Wave 75 Pool Cleaner | Operating Instructions 7. REMOTE CONTROL UNIT The Control Panel The remote control unit offers two operation modes Automatic mode and manual direction control mode. In automatic mode, the cleaning parameters can be changed. In manual direction mode, the robot's motion can be controlled manually. Radio reception meter When no black lines are showing, move closer to the power supply unit Battery level meter When flashing, change the batteries Manual control indicator When flashing, you are in manual direction control mode Cleaning cycle icons Delay timer icons Cleaning mode icons ON/OFF button Manual/automatic select button Set/OK button Direction control arrows Manual Direction Control Mode 1. Press the On/Off button once. The remote control will start in manual direction control mode. 2. Use the direction control arrows (see right) to control the movement of the robot around the pool. Exiting Manual Direction Control Mode and setting the Automatic Mode 1. To exit the manual direction control mode, press the Manual/Automatic select button once only. 2. The digital screen will light up and three rows of function icons will be displayed in default mode. 1. To change the parameters press the up or down arrows. 2. To select the parameter settings use the right or left arrows. When you reach the required function press the Set/OK button. 9 Dolphin Wave 75 Pool Cleaner | Operating Instructions Press the Manual/Automatic select button and then choose the desired parameters according to the following table: Cleaning cycle indicator This determines the length of the cleaning cycle. Fast 2-hour cycle Efficient 3-hour cycle for everyday use. (Default setting) Extra 4-hour cycle Delay time indicator This determines when the pool cleaner starts to work. Delaying allows the dirt to settle to the bottom of the pool. Immediate start (Default setting) One-hour delay Two-hour delay Cleaning action indicator Allowing you to choose from the following options. Standard Floor and wall cleaning. (Default setting) Ultra-clean Stronger suction and slower movement. (floor and wall) Floor only Cleans only the floor and the area where the floor and walls meet Walls only Cleans walls and waterline only Note: · After 2 minute if no button is pressed, the Remote Control Unit will shut-down and the Pool cleaner will continue to work in the previous settings. · When the "Ultra-Clean" and "Walls Only" options finish their cycles, the Pool Cleaner will return to default settings. 10 Dolphin Wave 75 Pool Cleaner | Operating Instructions Dolphin Wave 75 Pool Cleaner EN Caddy assembly 11 1 DIN 7985 A2 M5X35 x 2 2 DIN 127B A2 M5 x 2 3 DIN 1587 A2 M5 x 2 4 WN 1412 A2 KA50X16 x 6 1 2 4 4 3a 3b 4 4a 4b 4c * For Liberty models 12 5 7 4 4 9 6 3 8mm (5/16") 2 3 1 2 1 8 10 * For Remote Control models 13 Dolphin Wave 75 Pool Cleaner 8152240 www.maytronics.com