Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 4 Pages, 3.26MB
Document DEVICE REPORTFLC3 RThousing IS0756 0id+ 3.5" round trimless housing FLC3D | FLC3W LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING. - - non emergency thermally protected, non-ic optional - bar hangers sold separately key power off power on FLC3D | FLC3W ic/cp attention level see additional instructions WALL WASH ORIENTATION WALL FLC3D | FLC3W KEEP SHADED AREA FREE FROM OBSTRUCTION ABOVE CEILING SHORT CONE DNS SUPER SHORT CONE DSS 2.64" 2.64" .50" .50" 10.61" 10.61" 10.61" 10.61" 1 x2 2 TALL CONE 3.16" 3.16" DNT .50" .50" IS0756 REV. B Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 4 WOOD STUDS 3a x4 3b x4 METAL STUDS 4 x4 5 6 minimum ceiling thickness: 1/2" maximum ceiling thickness: 1-1/2" MUD-IN 1 COLLAR MUST OVERLAP BUT NOT EXCEED CEILING MATERIAL 2 make electrical connections 3 4 1/8" clean ceiling surface free of dust and debris 4 5 remove adhesive backing from mud ring 6 IS0756 REV. B use foam cylinder to align mud ring with housing collar opening Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 4 7 8 DRYWALL do not remove dust cover until tape and mud-in complete 9 MUD DRYWALL TAPE (BY OTHERS) MUD RING APPLY TAPE AND DRYWALL COMPOUND AT LEAST 8-12" OUT FROM APERTURE 10 scrape away excess mud compound from mud ring to expose trim recess WOOD CEILING wood ceiling installation kit parts list 1 wood routing jig 2 X4 5/16" miniature rabbeting bit with 1/16" cut depth 3m command poster strip #136 (qty. 40) 3 ADHERE WOOD ROUTING JIG TO WOOD CEILING SURFACE 4" CLEAN WOOD CEILING SURFACE AND WOOD ROUTING JIG FREE OF DUST AND DEBRIS 4 CREATE STARTER HOLE ADHERE COMMAND POSTER STRIPS TO WOOD ROUTING JIG IS0756 REV. B Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 4 5 CREATE MAIN HOLE USING WOOD CEILING JIG AS GUIDE 6 REMOVE WOOD ROUTING JIG FROM WOOD CEILING SURFACE 7 INSTALL 5/16" MINIATURE RABBETING BIT WITH 1/16" CUT DEPTH 8a 8b USE TRIM TO DOUBLE CHECK DEPTH 9 Trim Recess .065" SET DEPTH OF RABBETING BIT DRIVER SERVICE 1 TO PREVENT ELECTRICAL SHOCK, DISCONNECT ELECTRICAL SUPPLY BEFORE SERVICING CREATE TRIM RECESS USING RABBETING BIT 2 Contractor is responsible for adequately reinforcing walls and/or ceilings to support fixture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS0756 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 4Adobe PDF Library 16.0.7 Adobe InDesign 17.3 (Macintosh)