Test Report Zigbee
ALE USA Inc. OAW-AP152X OmniAccess Stellar 2AI9TOAW-AP152X 2AI9TOAWAP152X oaw ap152x
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 49 Pages, 3.55MB
Document DEVICE REPORTGetApplicationAttachment.html?id=8009200MRT Technology (Suzhou) Co., Ltd Phone: +86-512-66308358 Web: www.mrt-cert.com Report No.: 2408RSU020-U2 Report Version: V01 Issue Date: 2024-12-24 RF MEASUREMENT REPORT FCC ID: 2AI9TOAW-AP152X Applicant: ALE USA Inc. Product: OmniAccess Stellar Model No.: OAW-AP1521 Brand Name: Alcatel-Lucent Enterprise FCC Classification: Digital Transmission System (DTS) FCC Rule Part(s): Part 15 Subpart C (Section 15.247) Result: Complies Received Date: 2024-08-12 Test Date: 2024-10-09 ~ 2024-10-24 Reviewed By: Approved By: Vincent Yu Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Template Version:1.5 1 of 49 Report No. 2408RSU020-U2 Version V01 Revision History Description Initial Report Report No.: 2408RSU020-U2 Issue Date 2024-12-24 Note Valid 2 of 49 Report No.: 2408RSU020-U2 CONTENTS Description Page 1. General Information ................................................................................................................................5 1.1. Applicant ...................................................................................................................................... 5 1.2. Manufacturer ................................................................................................................................ 5 1.3. Testing Facility ............................................................................................................................. 5 1.4. Product Information...................................................................................................................... 6 1.5. Radio Specification under Test .................................................................................................... 6 1.6. Working Frequencies ................................................................................................................... 7 2. Test Configuration ...................................................................................................................................8 2.1. Test Mode..................................................................................................................................... 8 2.2. Test System Connection Diagram................................................................................................ 8 2.3. Test Software ............................................................................................................................... 8 2.4. Applied Standards........................................................................................................................ 9 2.5. Test Environment Condition ......................................................................................................... 9 3. Antenna Requirements .........................................................................................................................10 4. Measuring Instrument ...........................................................................................................................11 5. Decision Rules and Measurement Uncertainty ..................................................................................12 5.1. Decision Rules ........................................................................................................................... 12 5.2. Measurement Uncertainty .......................................................................................................... 12 6. Test Result..............................................................................................................................................13 6.1. 6.2. 6.2.1. 6.2.2. 6.2.3. 6.2.4. 6.2.5. 6.3. 6.3.1. 6.3.2. 6.3.3. 6.3.4. 6.3.5. 6.4. 6.4.1. 6.4.2. Summary .................................................................................................................................... 13 6dB Bandwidth Measurement.................................................................................................... 14 Test Limit .................................................................................................................................... 14 Test Procedure ........................................................................................................................... 14 Test Setting ................................................................................................................................ 14 Test Setup .................................................................................................................................. 14 Test Result ................................................................................................................................. 14 Output Power Measurement ...................................................................................................... 15 Test Limit .................................................................................................................................... 15 Test Procedure ........................................................................................................................... 15 Test Setting ................................................................................................................................ 15 Test Setup .................................................................................................................................. 15 Test Result ................................................................................................................................. 15 Power Spectral Density Measurement ...................................................................................... 16 Test Limit .................................................................................................................................... 16 Test Procedure ........................................................................................................................... 16 3 of 49 Report No.: 2408RSU020-U2 6.4.3. 6.4.4. 6.4.5. 6.5. 6.5.1. 6.5.2. 6.5.3. 6.5.4. 6.5.5. 6.6. 6.6.1. 6.6.2. 6.6.3. 6.6.4. 6.6.5. 6.7. 6.7.1. 6.7.2. 6.7.3. 6.7.4. 6.7.5. 6.8. 6.8.1. 6.8.2. 6.8.3. Test Setting ................................................................................................................................ 16 Test Setup .................................................................................................................................. 16 Test Result ................................................................................................................................. 16 Conducted Band Edge and Out-of-Band Emissions Measurement .......................................... 17 Test Limit .................................................................................................................................... 17 Test Procedure ........................................................................................................................... 17 Test Settitng ............................................................................................................................... 17 Test Setup .................................................................................................................................. 17 Test Result ................................................................................................................................. 18 Radiated Spurious Emission Measurement............................................................................... 19 Test Limit .................................................................................................................................... 19 Test Procedure ........................................................................................................................... 19 Test Setting ................................................................................................................................ 19 Test Setup .................................................................................................................................. 21 Test Result ................................................................................................................................. 22 Radiated Restricted Band Edge Measurement ......................................................................... 23 Test Limit .................................................................................................................................... 23 Test Procedure ........................................................................................................................... 24 Test Setting ................................................................................................................................ 24 Test Setup .................................................................................................................................. 25 Test Result ................................................................................................................................. 26 AC Conducted Emissions Measurement ................................................................................... 27 Test Limit .................................................................................................................................... 27 Test Setup .................................................................................................................................. 27 Test Result ................................................................................................................................. 27 Appendix A Test Result ...............................................................................................................................28 A.1 Duty Cycle Test Result ............................................................................................................... 28 A.2 6dB Bandwidth Test Result ........................................................................................................ 29 A.3 Output Power Test Result .......................................................................................................... 30 A.4 Power Spectral Density Test Result ........................................................................................... 31 A.5 Conducted Band Edge and Out-of-Band Emissions Test Result............................................... 32 A.6 Radiated Spurious Emission Test Result ................................................................................... 34 A.7 Radiated Restricted Band Edge Test Result.............................................................................. 38 A.8 AC Conducted Emissions Test Result ....................................................................................... 46 Appendix B Test Setup Photograph ..........................................................................................................48 Appendix C EUT Photograph .....................................................................................................................49 4 of 49 1. General Information 1.1. Applicant ALE USA Inc. 2000 Corporate Center Drive Thousand Oaks, CA 91320 Report No.: 2408RSU020-U2 1.2. Manufacturer ALE USA Inc. 2000 Corporate Center Drive Thousand Oaks, CA 91320 1.3. Testing Facility Test Site MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian'edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Location (Suzhou - Wujiang) Building 1, No.1 Xingdong Road, Wujiang, Suzhou, Jiangsu, People's Republic of China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 VCCI: R-20025 R-20141 G-20034 G-20134 C-20020 C-20103 T-20020 T-20104 Test Site MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 CNAS: L10551 FCC: CN1284 ISED: CN0105 Test Site MRT Taiwan Laboratory Laboratory Location (Taiwan) No. 38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Laboratory Accreditations TAF: 3261 FCC: 291082, TW3261 ISED: TW3261 5 of 49 Report No.: 2408RSU020-U2 1.4. Product Information Product Name OmniAccess Stellar Model No. OAW-AP1521 EUT Identification No. 20240929Sample#04 Wi-Fi Specification 802.11a/b/g/n/ac/ax/be Bluetooth Specification V5.1 single mode, BLE only Zigbee Specification 802.15.4 Antenna Information Refer to section 1.5 Power Type AC/DC Adapter Input or PoE Input Operating Environment Indoor Use Accessories Model: ADP-50GR B Adapter Input: 100-240V ~ 1.3A 50-60Hz Output: 48.0V, 1.042A 50.1W Model: POE60U-1BT-X (ALE P/N: POE60U-1BT-X-R) Input: 100-240V ~ 1.5A, 50/60Hz Output: 56.0V, 0.535A, 30W PoE Injector PIN 3, 6+ PIN 1, 2 Return Output: 56.0V, 0.535A, 30W PIN 4, 5+ PIN 7, 8 Return Remark: 1. The information of EUT was provided by the manufacturer, and the accuracy of the information shall be the responsibility of the manufacturer. 2. AC/DC Power Adapter and PoE Injector are not sold with Product. For this report, we select AC/DC Adapter for testing. 1.5. Radio Specification under Test Zigbee Specification Frequency Range Channel Number Type of Modulation Antenna Type Antenna Gain 802.15.4 2405 ~ 2480MHz 16 O-QPSK Dipole Antenna 5.3dBi 6 of 49 1.6. Working Frequencies Channel 11 14 17 20 23 26 Frequency 2405 MHz 2420 MHz 2435 MHz 2450 MHz 2465 MHz 2480 MHz Channel 12 15 18 21 24 -- Frequency 2410 MHz 2425 MHz 2440 MHz 2455 MHz 2470 MHz -- Report No.: 2408RSU020-U2 Channel 13 16 19 22 25 -- Frequency 2415 MHz 2430 MHz 2445 MHz 2460 MHz 2475 MHz -- 7 of 49 2. Test Configuration 2.1. Test Mode Mode 1: Transmit by 802.15.4 Report No.: 2408RSU020-U2 2.2. Test System Connection Diagram The device was tested per the guidance ANSI C63.10: 2013 was used to reference the appropriate EUT setup for radiated emissions testing and AC line conducted testing. Connection Diagram Cable Type A Power Cable B LAN Cable Product 1 Notebook Cable Description Non-Shielded Non-Shielded Manufacturer ThinkPad Length 1.5m > 10m Model No. E14 Gen 5 2.3. Test Software The test utility software used during testing was "IPOP" and commands were provided by the manufacturer. 8 of 49 Report No.: 2408RSU020-U2 2.4. Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: FCC Part 15.247 KDB 558074 D01v05r02 ANSI C63.10-2013 2.5. Test Environment Condition Ambient Temperature Relative Humidity 15 ~ 35°C 20 ~ 75%RH 9 of 49 Report No.: 2408RSU020-U2 3. Antenna Requirements Excerpt from §15.203 of the FCC Rules/Regulations: "An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section." The antenna of the device is permanently attached. There are no provisions for connection to an external antenna. Conclusion: The unit complies with the requirement of §15.203. 10 of 49 Report No.: 2408RSU020-U2 4. Measuring Instrument Instrument Signal Analyzer Thermohygrometer USB Power Sensor EMI Test Receiver Two-Line V-Network Four-Line V-Network Thermohygrometer Shielding Room EMI Test Receiver Preamplifier Signal Analyzer Thermohygrometer Active Loop Antenna TRILOG Antenna Horn Antenna Anechoic Chamber Manufacturer Model No. Asset No. Keysight N9010B MRTSUE07028 testo 608-H1 MRTSUE11022 Keysight U2021XA MRTSUE06596 R&S ESR3 MRTSUE06612 R&S ENV216 MRTSUE06003 R&S ENV432 MRTSUE06614 testo 608-H1 MRTSUE06621 MIX-BEP SIP-SR2 MRTSUE06949 R&S ESR3 MRTSUE06185 EMCI EMC184045SE MRTSUE06602 Keysight N9010B MRTSUE07028 testo 608-H1 MRTSUE06622 Schwarzbeck FMZB 1519-60 D MRTSUE07075 Schwarzbeck VULB 9168 MRTSUE06647 Schwarzbeck BBHA 9120D MRTSUE06648 RIKEN SIP-AC2 MRTSUE06781 Cali. Interval Cali. Due Date Test Site 1 year 2025-10-13 SIP-TR1 1 year 2024-10-28 SIP-TR1 1 year 2025-07-23 SIP-TR1 1 year 2025-05-08 SIP-SR2 1 year 2025-05-08 SIP-SR2 1 year 2025-10-13 SIP-SR2 1 year 2024-11-03 SIP-SR2 5 years 2029-10-13 SIP-SR2 1 year 2024-12-17 SIP-AC2 1 year 2025-10-08 SIP-AC2 1 year 2025-10-13 SIP-AC2 1 year 2024-11-03 SIP-AC2 1 year 2024-12-04 SIP-AC2 1 year 2025-06-15 SIP-AC2 1 year 2024-10-21 SIP-AC2 1 year 2024-12-21 SIP-AC2 Software Version e3 230711 Agilent Power Analyzer/Agilent Power Panel V R03.09.00 Controller_MF 7802BS 1.02 Function EMI Test Software Power RE Antenna & Turntable 11 of 49 Report No.: 2408RSU020-U2 5. Decision Rules and Measurement Uncertainty 5.1. Decision Rules The Decision Rule is based on Simple Acceptance in accordance with ISO Guide 98-4: 2012 Clause 8.2. (Measurement uncertainty is not taken into account when stating conformity with a specified requirement.) 5.2. Measurement Uncertainty Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement The maximum measurement uncertainty is evaluated as: 9kHz~150kHz: 3.58dB 150kHz~30MHz: 3.20dB Radiated Emission Measurement The maximum measurement uncertainty is evaluated as: Coaxial: 9kHz~30MHz: 2.61dB Coplanar: 9kHz~30MHz: 2.62dB Horizontal: 30MHz~200MHz: 3.79dB 200MHz~1GHz: 3.91dB 1GHz~40GHz: 4.99dB Vertical: 30MHz~200MHz: 4.06dB 200MHz~1GHz: 5.21dB 1GHz~40GHz: 4.90dB Spurious Emissions, Conducted Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.2dB Output Power Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 1.4dB Power Spectrum Density Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.2dB Occupied Bandwidth Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 2.7% 12 of 49 Report No.: 2408RSU020-U2 6. Test Result 6.1. Summary FCC Section(s) 15.247(a)(2) Test Description 6dB Bandwidth Test Condition Verdict Pass 15.247(b)(3) 15.247(e) Output Power Power Spectral Density Conducted Pass Pass 15.247(d) Band Edge / Out-of-Band Emissions Pass 15.205 15.209 General Field Strength (Restricted Bands and Radiated Emission) Radiated Pass 15.207 AC Conducted Emissions 150kHz - 30MHz Line Conducted Pass Notes: 1. The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 2. For radiated emission tests, every axis (X, Z) was also verified. The test results shown in the following sections represent the worst-case emissions. 13 of 49 Report No.: 2408RSU020-U2 6.2. 6dB Bandwidth Measurement 6.2.1. Test Limit The minimum 6dB bandwidth shall be at least 500 kHz. 6.2.2. Test Procedure ANSI C63.10 - 2013 - Section 11.8 6.2.3. Test Setting 1. The Spectrum's automatic bandwidth measurement capability was used to perform the 6dB bandwidth measurement. The "X" dB bandwidth parameter was set to X = 6. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. Set RBW = 100 kHz 3. VBW 3 × RBW 4. Detector = Peak 5. Trace mode = Max hold 6. Sweep = Auto couple 7. Allow the trace to stabilize 6.2.4. Test Setup 6.2.5. Test Result Refer to Appendix A.2. 14 of 49 Report No.: 2408RSU020-U2 6.3. Output Power Measurement 6.3.1. Test Limit The maximum output power shall be less 1 Watt (30dBm). The conducted output power limit specified in paragraph FCC Part 15.247(b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. If transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs FCC Part 15.247(b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 6.3.2. Test Procedure ANSI C63.10 - 2013 - Section 11.9.2.3.2 6.3.3. Test Setting Method PKPM1 (Peak Power Measurement of Signals with DTS BW 50MHz) Peak power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The pulse sensor employs a VBW = 50MHz so this method was only used for signals whose DTS bandwidth was less than or equal to 50MHz. Average Power Measurement Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. 6.3.4. Test Setup 6.3.5. Test Result Refer to Appendix A.3. 15 of 49 Report No.: 2408RSU020-U2 6.4. Power Spectral Density Measurement 6.4.1. Test Limit The maximum permissible power spectral density is 8dBm in any 3 kHz band. The same method of determining the conducted output power shall be used to determine the power spectral density. 6.4.2. Test Procedure ANSI C63.10 - 2013 - Section 11.10.2 6.4.3. Test Setting 1. Analyzer was set to the center frequency of the DTS channel under investigation 2. Span = 1.5 times the DTS channel bandwidth 3. RBW = 3kHz 4. VBW = 10kHz 5. Detector = peak 6. Sweep time = auto couple 7. Trace mode = max hold 8. Trace was allowed to stabilize 6.4.4. Test Setup 6.4.5. Test Result Refer to Appendix A.4. 16 of 49 Report No.: 2408RSU020-U2 6.5. Conducted Band Edge and Out-of-Band Emissions Measurement 6.5.1. Test Limit The limit for out-of-band spurious emissions at the band edge is 20dB below the fundamental emission level, as determined from the in-band power measurement of the DTS channel performed in a 100 kHz bandwidth per the PSD procedure. 6.5.2. Test Procedure ANSI C63.10-2013 - Section 11.11 6.5.3. Test Setting Reference level measurement 1. Set instrument center frequency to DTS channel center frequency 2. Set the span to 1.5 times the DTS bandwidth 3. Set the RBW = 100 kHz 4. Set the VBW 3 x RBW 5. Detector = peak 6. Sweep time = auto couple 7. Trace mode = max hold 8. Allow trace to fully stabilize Emission level measurement 1. Set the center frequency and span to encompass frequency range to be measured 2. RBW = 100kHz 3. VBW = 300kHz 4. Detector = Peak 5. Trace mode = max hold 6. Sweep time = auto couple 7. The trace was allowed to stabilize 6.5.4. Test Setup 17 of 49 6.5.5. Test Result Refer to Appendix A.5. Report No.: 2408RSU020-U2 18 of 49 Report No.: 2408RSU020-U2 6.6. Radiated Spurious Emission Measurement 6.6.1. Test Limit All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table per Section 15.209. Frequency [MHz] 0.009 - 0.490 0.490 - 1.705 1.705 - 30 30 - 88 88 - 216 216 - 960 Above 960 FCC Part 15 Subpart C Paragraph 15.209 Field Strength [uV/m] 2400/F (kHz) 24000/F (kHz) 30 100 150 200 500 Measured Distance [Meters] 300 30 30 3 3 3 3 6.6.2. Test Procedure ANSI C63.10 - 2013 - Section 11.11 & 11.12 ANSI C63.10 - 2013 - Section 6.3 (General Requirements) ANSI C63.10 - 2013 - Section 6.4 (Standard test method below 30MHz) ANSI C63.10 - 2013 - Section 6.5 (Standard test method above 30MHz to 1GHz) ANSI C63.10 - 2013 - Section 6.6 (Standard test method above 1GHz) 6.6.3. Test Setting Table 1 - RBW as a function of frequency Frequency 9 ~ 150 kHz 0.15 ~ 30 MHz 30 ~ 1000 MHz > 1000MHz RBW 200 ~ 300 Hz 9 ~ 10 kHz 100 ~ 120 kHz 1MHz 19 of 49 Report No.: 2408RSU020-U2 Quasi-Peak Measurements below 1GHz 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. Span was set greater than 1MHz 3. RBW = as specified in Table 1 4. Detector = CISPR quasi-peak 5. Sweep time = auto couple 6. Trace was allowed to stabilize Peak Measurements above 1GHz 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3MHz 4. Detector = Peak 5. Sweep time = Auto couple 6. Trace mode = Max hold 7. Trace was allowed to stabilize Average Measurements above 1GHz (Method VB) 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW; if the EUT is configured to transmit with duty cycle 98%, set VBW = 10Hz If the EUT duty cycle is < 98%, set VBW 1/T. T is the minimum transmission duration. 4. As an alternative, the instrument may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some instruments require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to "Voltage" regardless of the display mode 5. Detector = Peak 6. Sweep time = Auto 7. Trace mode = Max hold 8. Trace was allowed to stabilize 20 of 49 6.6.4. Test Setup Below 30MHz Test Setup: Report No.: 2408RSU020-U2 Below 1GHz Test Setup: 21 of 49 Above 1GHz Test Setup: Report No.: 2408RSU020-U2 6.6.5. Test Result Refer to Appendix A.6. 22 of 49 Report No.: 2408RSU020-U2 6.7. Radiated Restricted Band Edge Measurement 6.7.1. Test Limit For 15.205 requirement: Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a) of FCC part 15, must also comply with the radiated emission limits specified in Section 15.209(a). Frequency (MHz) 0.090 - 0.110 1 0.495 - 0.505 2.1735 - 2.1905 4.125 - 4.128 4.17725 - 4.17775 4.20725 - 4.20775 6.215 - 6.218 6.26775 - 6.26825 6.31175 - 6.31225 8.291 - 8.294 8.362 - 8.366 8.37625 - 8.38675 8.41425 - 8.41475 12.29 - 12.293 12.51975 - 12.52025 12.57675 - 12.57725 13.36 - 13.41 Frequency (MHz) 16.42 - 16.423 16.69475 - 16.69525 16.80425 - 16.80475 25.5 - 25.67 37.5 - 38.25 73 - 74.6 74.8 - 75.2 108 - 121.94 123 - 138 149.9 - 150.05 156.52475 - 156.52525 156.7 - 156.9 162.0125 - 167.17 167.72 - 173.2 240 - 285 322 - 335.4 -- Frequency (MHz) 399.9 - 410 608 - 614 960 - 1240 1300 - 1427 1435 - 1626.5 1645.5 - 1646.5 1660 - 1710 1718.8 - 1722.2 2200 - 2300 2310 - 2390 2483.5 - 2500 2690 - 2900 3260 - 3267 3332 - 3339 3345.8 - 3358 3600 - 4400 -- Frequency (GHz) 4.5 - 5.15 5.35 - 5.46 7.25 - 7.75 8.025 - 8.5 9.0 - 9.2 9.3 - 9.5 10.6 - 12.7 13.25 - 13.4 14.47 - 14.5 15.35 - 16.2 17.7 - 21.4 22.01 - 23.12 23.6 - 24.0 31.2 - 31.8 36.43 - 36.5 (2) -- 23 of 49 Report No.: 2408RSU020-U2 All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47CFR must not exceed the limits shown in Table per Section 15.209. FCC Part 15 Subpart C Paragraph 15.209 Frequency [MHz] 0.009 - 0.490 0.490 - 1.705 1.705 - 30 30 - 88 88 - 216 216 - 960 Above 960 Field Strength [uV/m] 2400/F (kHz) 24000/F (kHz) 30 100 150 200 500 Measured Distance [Meters] 300 30 30 3 3 3 3 6.7.2. Test Procedure ANSI C63.10-2013 Section 6.3 & 6.6 & 11.13 6.7.3. Test Setting Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple 6. Trace mode = max hold 7. Trace was allowed to stabilize 24 of 49 Report No.: 2408RSU020-U2 Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW; If the EUT is configured to transmit with duty cycle 98%, set VBW = 10 Hz. If the EUT duty cycle is < 98%, set VBW 1/T. T is the minimum transmission duration. 4. As an alternative, the instrument may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some instruments require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to "Voltage" regardless of the display mode 5. Detector = Peak 6. Sweep time = auto 7. Trace mode = max hold 8. Allow max hold to run for at least 50 times (1/duty cycle) traces 6.7.4. Test Setup 25 of 49 6.7.5. Test Result Refer to Appendix A.7. Report No.: 2408RSU020-U2 26 of 49 Report No.: 2408RSU020-U2 6.8. AC Conducted Emissions Measurement 6.8.1. Test Limit Frequency (MHz) FCC Part 15 Subpart C Paragraph 15.207 Limits QP (dBuV) AV (dBuV) 0.15 - 0.50 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 6.8.2. Test Setup 6.8.3. Test Result Refer to Appendix A.8. 27 of 49 Report No.: 2408RSU020-U2 Appendix A Test Result A.1 Duty Cycle Test Result Test Site Test Date SIP-TR1 2024-10-17 Test Mode 802.15.4 Test Engineer Ryan Wang Duty Cycle 100% 802.15.4 Duty Cycle (T = Transmission Duration) 28 of 49 A.2 6dB Bandwidth Test Result Test Site Test Date SIP-TR1 2024-10-17 Report No.: 2408RSU020-U2 Test Engineer Ryan Wang Test Mode 802.15.4 802.15.4 802.15.4 Modulation Mode O-QPSK O-QPSK O-QPSK Channel No. 11 18 26 Frequency (MHz) 2405 2440 2480 6dB Bandwidth (MHz) 1.642 1.636 1.647 Limit (MHz) 0.5 0.5 0.5 Result Pass Pass Pass Channel 11 (2405MHz) 802.15.4 6dB Bandwidth Channel 18 (2440MHz) Channel 26 (2480MHz) 29 of 49 Report No.: 2408RSU020-U2 A.3 Output Power Test Result Test Site Test Date SIP-TR1 2024-10-17 Test Engineer Ryan Wang Test Result of Peak Output Power Test Mode 802.15.4 802.15.4 Modulation Mode O-QPSK O-QPSK Channel No. 11 18 802.15.4 O-QPSK 26 Freq. (MHz) 2405 2440 2480 Peak Power (dBm) 9.49 9.45 9.27 Limit (dBm) 30.00 30.00 30.00 Result Pass Pass Pass Test Result of Average Output Power (Reporting Only) Test Mode 802.15.4 802.15.4 802.15.4 Modulation Mode O-QPSK O-QPSK O-QPSK Channel No. 11 18 26 Freq. (MHz) 2405 2440 2480 Average Power (dBm) 9.46 9.41 9.22 Limit (dBm) 30.00 30.00 30.00 Result Pass Pass Pass 30 of 49 A.4 Power Spectral Density Test Result Test Site Test Date SIP-TR1 2024-10-17 Report No.: 2408RSU020-U2 Test Engineer Ryan Wang Test Mode 802.15.4 802.15.4 802.15.4 Modulation Channel No. Frequency Mode (MHz) O-QPSK 11 2405 O-QPSK 18 2440 O-QPSK 26 2480 PK PSD (dBm / 3kHz) -6.10 -6.12 -6.31 Limit (dBm / 3kHz) 8.00 8.00 8.00 Result Pass Pass Pass Channel 11 (2405MHz) 802.15.4 Power Density Channel 18 (2440MHz) Channel 26 (2480MHz) 31 of 49 Report No.: 2408RSU020-U2 A.5 Conducted Band Edge and Out-of-Band Emissions Test Result Test Site SIP-TR1 Test Engineer Test Date 2024-10-17 Ryan Wang Test Mode 802.15.4 802.15.4 802.15.4 Data Rate / MCS O-QPSK O-QPSK O-QPSK Channel No. 11 18 26 Frequency (MHz) 2405 2440 2480 Limit (dBc) 20 20 20 Result Pass Pass Pass 802.15.4 Out-of-Band Emissions Channel 11 (2405MHz) 100kHz PSD Reference Level Low Band Edge Spurious Emission 32 of 49 Report No.: 2408RSU020-U2 Channel 18 (2440MHz) 100kHz PSD Reference Level Spurious Emission Channel 26 (2480MHz) 100kHz PSD Reference Level High Band Edge Spurious Emission 33 of 49 Report No.: 2408RSU020-U2 A.6 Radiated Spurious Emission Test Result Test Site Test Date Remark: SIP-AC2 Test Engineer Fusco Pan 2024-10-18 1. Average measurement was not performed if peak level lower than average limit. 2. Other frequency was 20dB below limit line within 1-18GHz, there is not shown in the report. Test Frequency Channel (MHz) 4809.7 4809.7 14809.1 14809.1 17996.6 17996.6 4809.7 11 4809.7 9647.9 9647.9 14239.6 14239.6 17926.9 17926.9 4881.1 4881.1 14511.6 14511.6 17923.5 17923.5 18 9647.9 9647.9 14574.5 14574.5 17887.8 17887.8 9647.9 26 9647.9 Reading Level (dBV) 48.6 60.2 26.0 39.6 24.3 36.7 49.3 55.7 38.4 45.7 26.4 40.4 24.9 38.4 41.2 52.5 26.2 38.8 25.0 38.4 39.5 45.5 26.2 38.9 24.2 37.3 29.1 44.1 Factor (dB/m) -6.2 -6.2 10.6 10.6 17.7 17.7 -6.2 -6.2 3.7 3.7 9.6 9.6 16.9 16.9 -5.8 -5.8 11.0 11.0 17.1 17.1 3.7 3.7 10.3 10.3 16.5 16.5 3.7 3.7 Measure Level (dBV/m) 42.4 54.0 36.6 50.2 42.0 54.4 43.1 49.5 42.1 49.4 36.0 50.0 41.8 55.3 35.4 46.7 37.2 49.8 42.1 55.5 43.2 49.2 36.5 49.2 40.7 53.8 32.8 47.8 34 of 49 Limit Margin Detector (dBV/m) (dB) 54.0 -11.6 Average 74.0 -20.0 Peak 54.0 -17.4 Average 74.0 -23.8 Peak 54.0 -12.0 Average 74.0 -19.6 Peak 54.0 -10.9 Average 74.0 -24.5 Peak 54.0 -11.9 Average 74.0 -24.6 Peak 54.0 -18.0 Average 74.0 -24.0 Peak 54.0 -12.2 Average 74.0 -18.7 Peak 54.0 -18.6 Average 74.0 -27.3 Peak 54.0 -16.8 Average 74.0 -24.2 Peak 54.0 -11.9 Average 74.0 -18.5 Peak 54.0 -10.8 Average 74.0 -24.8 Peak 54.0 -17.5 Average 74.0 -24.8 Peak 54.0 -13.3 Average 74.0 -20.2 Peak 54.0 -21.2 Average 74.0 -26.2 Peak Polarization Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical Vertical Vertical Horizontal Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical Vertical Horizontal Horizontal Report No.: 2408RSU020-U2 14809.1 25.1 10.6 35.7 54.0 -18.3 Average 14809.1 39.3 10.6 49.9 74.0 -24.1 Peak 17926.9 24.3 16.9 41.2 54.0 -12.8 Average 17926.9 37.6 16.9 54.5 74.0 -19.5 Peak 9647.9 29.3 3.7 33.0 54.0 -21.0 Average 9647.9 46.1 3.7 49.8 74.0 -24.2 Peak 14812.5 25.2 10.5 35.7 54.0 -18.3 Average 14812.5 40.7 10.5 51.2 74.0 -22.8 Peak 17925.2 24.1 17.0 41.1 54.0 -12.9 Average 17925.2 39.0 17.0 56.0 74.0 -18.0 Peak Note: Measure Level (dBV/m) = Reading Level (dBV) + Factor (dB/m) Factor (dB/m) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Horizontal Horizontal Horizontal Horizontal Vertical Vertical Vertical Vertical Vertical Vertical 35 of 49 Report No.: 2408RSU020-U2 The Result of Radiated Emission below 1GHz: Site SIP-AC2 Test Engineer Fusco Pan Factor VULB 9168_00999_25-2000MHz EUT OmniAccess Stellar (OAW-AP1521) Test Mode Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-18 24.3C /65.2% Horizontal AC 120V/60Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) Margin (dB) Limit (dBV/m) Detector 1 84.821 11.90 14.87 26.77 -13.23 40.00 QP 2 129.968 17.60 18.98 36.58 -6.92 43.50 QP 3 146.733 14.80 20.24 35.04 -8.46 43.50 QP 4 * 158.390 19.60 20.44 40.04 -3.46 43.50 QP 5 266.890 14.20 19.75 33.95 -12.05 46.00 QP 6 326.396 10.90 21.71 32.61 -13.39 46.00 QP Notes: 1. " * ", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m)+ Cable Loss (dB). 3. Measurement (dBV/m) = Reading (dBV) + C.F (dB/m). 4. The amplitude of radiated emissions (frequency range from 9kHz to 30MHz and 18GHz to 25GHz) is that proximity to ambient noise, which also are attenuated more than 20 dB below the permissible value. Therefore, the data is not presented in the report. 36 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC2 Fusco Pan VULB 9168_00999_25-2000MHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-18 24.3C /65.2% Vertical AC 120V/60Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) Margin (dB) Limit (dBV/m) Detector 1 * 34.252 15.80 19.12 34.92 -5.08 40.00 QP 2 41.509 10.80 20.08 30.88 -9.12 40.00 QP 3 60.939 8.40 19.59 27.99 -12.01 40.00 QP 4 82.186 17.10 15.35 32.45 -7.55 40.00 QP 5 129.968 18.90 18.98 37.88 -5.62 43.50 QP 6 169.065 13.70 19.99 33.69 -9.81 43.50 QP Notes: 1. " * ", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m)+ Cable Loss (dB). 3. Measurement (dBV/m) = Reading (dBV) + C.F (dB/m). 4. The amplitude of radiated emissions (frequency range from 9kHz to 30MHz and 18GHz to 25GHz) is that proximity to ambient noise, which also are attenuated more than 20 dB below the permissible value. Therefore, the data is not presented in the report. 37 of 49 Report No.: 2408RSU020-U2 A.7 Radiated Restricted Band Edge Test Result Site SIP-AC3 Test Engineer Mero Zhou Factor HF907_102861_1-18GHz EUT OmniAccess Stellar (OAW-AP1521) Test Mode Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Horizontal AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 2366.680 27.99 32.62 60.61 2 2390.000 25.67 32.69 58.36 3 * 2405.590 74.67 32.75 107.42 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) -13.39 -15.64 N/A Limit (dBV/m) 74.00 74.00 N/A Detector Peak Peak Peak 38 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Horizontal AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 2390.000 14.52 32.69 47.21 2 * 2405.040 70.78 32.75 103.52 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) -6.79 N/A Limit (dBV/m) 54.00 N/A Detector Average Average 39 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Vertical AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 2360.350 27.66 32.61 60.27 2 2390.000 25.99 32.69 58.68 3 * 2405.560 69.86 32.75 102.61 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) -13.73 -15.32 N/A Limit (dBV/m) 74.00 74.00 N/A Detector Peak Peak Peak 40 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Vertical AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 2390.000 14.46 32.69 47.15 2 * 2405.030 65.86 32.75 98.61 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) -6.85 N/A Limit (dBV/m) 54.00 N/A Detector Average Average 41 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2480MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Horizontal AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 * 2479.492 72.79 33.11 105.90 2 2483.500 29.70 33.13 62.83 3 2484.005 30.74 33.13 63.87 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) N/A -11.17 -10.13 Limit (dBV/m) N/A 74.00 74.00 Detector Peak Peak Peak 42 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2480MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Horizontal AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 * 2480.038 68.91 33.11 102.02 2 2483.500 19.43 33.13 52.56 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) N/A -1.44 Limit (dBV/m) N/A 54.00 Detector Average Average 43 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2480MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Vertical AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 * 2479.450 65.21 33.11 98.33 2 2483.500 27.30 33.13 60.43 3 2496.373 28.65 33.19 61.84 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) N/A -13.57 -12.16 Limit (dBV/m) N/A 74.00 74.00 Detector Peak Peak Peak 44 of 49 Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-AC3 Mero Zhou HF907_102861_1-18GHz OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2480MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-24 24.3C /65.2% Vertical AC 120V/50Hz Frequency No Mark (MHz) Reading (dBV) C.F (dB/m) Measurement (dBV/m) 1 * 2480.038 61.07 33.11 94.18 2 2483.500 16.18 33.13 49.31 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB). 3. Measurement(dBV/m) = Reading(dBV) + C.F (dB/m). Margin (dB) N/A -4.69 Limit (dBV/m) N/A 54.00 Detector Average Average 45 of 49 Report No.: 2408RSU020-U2 A.8 AC Conducted Emissions Test Result Site SIP-SR2 Test Engineer Arvin Ding Factor SIP-SR2-ENV216_101684_C EUT OmniAccess Stellar (OAW-AP1521) Test Mode Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-09 24.1C /52.6% Line AC 120V/60Hz Frequency No Mark (MHz) Reading (dBV) C.F Measurement (dB) (dBV) 1 0.154 21.00 9.65 30.65 2 * 0.154 40.24 9.65 49.90 3 0.162 18.60 9.65 28.26 4 0.162 39.38 9.65 49.03 5 0.190 14.55 9.67 24.22 6 0.190 34.45 9.67 44.12 7 0.206 11.04 9.70 20.73 8 0.206 31.55 9.70 41.25 9 0.242 11.69 9.72 21.41 10 0.242 26.72 9.72 36.44 11 0.394 11.25 9.74 20.99 12 0.394 21.17 9.74 30.91 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB) = LISN Factor (dB) + Cable Loss (dB). 3. Measurement (dBV) = Reading (dBV) + C.F (dB). Margin (dB) -25.13 -15.88 -27.10 -16.33 -29.82 -19.91 -32.63 -22.12 -30.62 -25.59 -26.99 -27.07 46 of 49 Limit (dBV) 55.78 65.78 55.36 65.36 54.04 64.04 53.37 63.37 52.03 62.03 47.98 57.98 Detector Average QP Average QP Average QP Average QP Average QP Average QP Report No.: 2408RSU020-U2 Site Test Engineer Factor EUT Test Mode SIP-SR2 Arvin Ding SIP-SR2-ENV216_101684_C OmniAccess Stellar (OAW-AP1521) Transmit by Zigbee at 2405MHz Test Date Temp./Humidity Polarity Test Voltage 2024-10-09 24.1C /52.6% Neutral AC 120V/60Hz Frequency No Mark (MHz) Reading (dBV) C.F Measurement (dB) (dBV) 1 0.150 21.36 9.68 31.04 2 0.150 39.89 9.68 49.57 3 0.162 19.31 9.68 28.99 4 * 0.162 39.33 9.68 49.01 5 0.182 15.84 9.68 25.52 6 0.182 35.61 9.68 45.30 7 0.206 11.35 9.72 21.06 8 0.206 31.56 9.72 41.27 9 0.226 9.33 9.73 19.06 10 0.226 28.08 9.73 37.81 11 0.354 9.73 9.75 19.48 12 0.354 20.41 9.75 30.16 Notes: 1. " *", means this data is the worst emission level. 2. C.F (dB) = LISN Factor (dB) + Cable Loss (dB). 3. Measurement (dBV) = Reading (dBV) + C.F (dB). Margin (dB) -24.96 -16.43 -26.37 -16.35 -28.87 -19.10 -32.30 -22.10 -33.54 -24.78 -29.39 -28.71 47 of 49 Limit (dBV) 56.00 66.00 55.36 65.36 54.39 64.39 53.37 63.37 52.60 62.60 48.87 58.87 Detector Average QP Average QP Average QP Average QP Average QP Average QP Appendix B Test Setup Photograph Refer to "2408RSU020-UT" file. Report No.: 2408RSU020-U2 48 of 49 Appendix C EUT Photograph Refer to "2408RSU020-UE" file. Report No.: 2408RSU020-U2 The End 49 of 49
Related FCC IDs:
- 2AI9TOAW-AP152X - ALE USA Inc. OmniAccess Stellar [OAW-AP152X] Microsoft Word 适用于 Microsoft 365 Microsoft Word 适用于 Microsoft 365