TWestendorp

PRODUCT MANUAL

1) The switch can be turned on manually for either 30 or 60 minutes. 2) The switch can function as a continuous timer which is intended to pro

PRODUCT MANUAL - Rackcdn.com

The envirotouchâ„¢ is a range of intelligent, timer based switches which allows easy, point-of-use control of lighting and electrical devices.

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 8 Pages, 1.98MB

Document DEVICE REPORT85017fb3-3c20-4b80-85d8-aec9f63e606e
PRODUCT MANUAL
The envirotouchTM is a range of intelligent, timer based switches which allows easy, point-of-use control of lighting and electrical devices. It includes multiple pre-set, countdown timer options or cycles, so with the simple press of a button it will automatically turn off the appliance, after the desired time. Designed for simple retrofitting of current switches and power sockets; can be hard-wired to light circuits or used with plug-in appliances to give intelligent control, but at a fraction of the cost. envirotouchTM comes in 8 different styles, so you can use them throughout the home or workplace and increase the benefits. The envirotouchTM range is supplied by Thermofilm Australia Pty Ltd, based in Melbourne.
The intelligent, energy saving solution

Specifications - Australia

MODEL

DESCRIPTION

OUTPUT WIRING

APPLIANCES

CURRENT (AMPS)

Rev E DEC15 TIME

TT-ET1P TT-ET1L

SINGLE LIGHT / APPLIANCE

TT-ET2P TT-ET2L

DOUBLE LIGHT / APPLIANCE

TT-ET3P TT-ET3L

APPLIANCE PLUG-IN

TT-ET4P TT-ET4L

HEATED TOWEL RAIL

MODEL

SWITCH TYPE

OUTPUT POWER

OPERATING TEMPERATURE

UNIT WEIGHT

APPROVALS

UNIT DIMENSIONS PROTECTION RATING

INTERNAL INTERNAL 3 PIN SOCKET INTERNAL

SINGLE DOUBLE SINGLE SINGLE

10 2 x 10 Amp
10 10

Continuous, 15, 45, 60, 120 min Continuous, 15, 45, 60, 120 min Continuous, 15, 45, 60, 120 min
30, 60, 2x4h, 2x6H

Electronic switch for power savings by the addition of a timer option

Refer to model code chart above 220-240 Volts Nominal at 50 Hertz, Single Phase -10oC TO 45oC

100g

AUSTRALIA/NZ 118x74x13mm

TTET1/ TT-ET2/ TT-ET4

AS/NZS60669

TT-ET3

AS/NZS/60669; 3100; 3112

For internal use only

NOTE:

"INTERNAL" means the wiring from the back of the controller for concealed wiring.

Controllers are available in portrait and landscape profile.

The Envirotouch range is not suitable to be used for two way lighting (two switches controlling one appliance)

For models, TT-ET1/L & TT-ET2/L, 3 minutes before the switch turns off the light, the lights will dip momentarily to warn you the light will be turned off.

The power draw when in the OFF position is less than 1 Watt.

The Neutral Wire must be connected to the controller unit.

All wiring must be performed by a suitable licenced electrician.

Note: Suitable for internal applications only.

CONTROLLER IN WALL MOUNTING DIAGRAM

2

TT-ET1P & TT-ET1L SINGLE SWITCH FOR LIGHT OR APPLIANCE
The TT-ET1P & TT-ET1L has been designed for applications such as lights or electrical devices.

TO TURN ON Press button

OUTPUT ON

Press button again within ON 3 seconds

Press button again within ON 3 seconds

Press button again within ON 3 seconds

Press button again within ON 3 seconds

Press button again within ON 3 seconds

TO TURN OFF

Wait 3 seconds then

OFF

press button

CHANGE DEFAULT

Press button and hold for OFF 5 seconds

Press button again within OFF 3 seconds

Press button again within OFF 3 seconds

Press button again within OFF 3 seconds

Press button again within OFF 3 seconds

Press button again within OFF 3 seconds

Don't press the button

OFF

for 5 seconds

LIGHTS All lights flash once then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights flash once then go OFF

FUNCTION The output will stay ON indefinitely Output will turn OFF after 15 minutes Output will turn OFF after 45 minutes Output will turn OFF after 60 minutes Output will turn OFF after 120 minutes The output will stay ON indefinitely

All lights go OFF

The output will stay OFF indefinitely

All lights flash ON, then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights go ON and stay ON

This will change the default for the first time the button is pushed. The factory setting is ON continuous for the first time the button is pushed The default will be changed to 15 minutes
The default will be changed to 45 minutes
The default will be changed to 60 minutes
The default will be changed to 120 minutes
The default will be changed to ON indefinitely

All lights flash ON twice then go OFF

The default program will be exited

3

TT-ET2P & TT-ET2L DOUBLE SWITCH FOR 2 x LIGHT CIRCUITS OR APPLIANCES
The Double Wall Switch is for operating 2 x light circuit or appliances.

TO TURN ON Press button

OUTPUT ON

Press button again within ON 3 seconds

Press button again within ON

3 seconds

Press button again within ON

3 seconds

Press button again within ON

3 seconds

Press button again within ON 3 seconds

TO TURN OFF

Wait 3 seconds then

OFF

press button

CHANGE DEFAULT

Press button and hold for OFF

5 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Don't press the button

OFF

for 5 seconds

LIGHTS All lights flash once then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights flash once then go OFF

FUNCTION The output will stay ON indefinitely Output will turn OFF after 15 minutes Output will turn OFF after 45 minutes Output will turn OFF after 60 minutes Output will turn OFF after 120 minutes The output will stay ON indefinitely

All lights go OFF

The output will stay OFF indefinitely

All lights flash ON, then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights go ON and stay ON

This will change the default for the first time the button is pushed. The factory setting is ON continuous for the first time the button is pushed The default will be changed to 15 minutes
The default will be changed to 45 minutes
The default will be changed to 60 minutes
The default will be changed to 120 minutes
The default will be changed to ON indefinitely

All lights flash ON twice then go OFF

The default program will be exited

4

TT-ET3P & TT-ET3L PLUG-IN APPLIANCE SWITCH
The TT-ET3P & TT-ET3L has been designed to be used with appliances that have a 3 pin Australian plug and draw no more than 10amps. They are suitable for heaters, fans, pumps and other appliances that can be controlled by a timer.

TO TURN ON Press button

OUTPUT ON

Press button again within ON

3 seconds

Press button again within ON

3 seconds

Press button again within ON

3 seconds

Press button again within ON 3 seconds

Press button again within ON 3 seconds

TO TURN OFF

Wait 3 seconds then

OFF

press button

CHANGE DEFAULT

Press button and hold for OFF 5 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Press button again within OFF

3 seconds

Don't press the button

OFF

for 5 seconds

LIGHTS All lights flash once then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights flash once then go OFF

FUNCTION The output will stay ON indefinitely Output will turn OFF after 15 minutes Output will turn OFF after 45 minutes Output will turn OFF after 60 minutes Output will turn OFF after 120 minutes The output will stay ON indefinitely

All lights go OFF

The output will stay OFF indefinitely

All lights flash ON, then go OFF
The 15 minute light will come ON and stay ON The 45 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 120 minute light will come ON and stay ON All lights go ON and stay ON

This will change the default for the first time the button is pushed. The factory setting is ON continuous for the first time the button is pushed The default will be changed to 15 minutes
The default will be changed to 45 minutes
The default will be changed to 60 minutes
The default will be changed to 120 minutes
The default will be changed to ON indefinitely

All lights flash ON twice then go OFF

The default program will be exited

5

TT-ET4P & TT-ET4L HEATED TOWEL RAIL SWITCH
The TT-ET4P & TT-ET4L has been developed for use with heated towel rails. It can also be used with other appliances that are suitable to be used on a 24 hour cycle.
OPERATION
The TT-ET4 & TT-ET4L has 2 modes of operation: 1) The switch can be turned on manually for either 30 or 60 minutes. 2) The switch can function as a continuous timer which is intended to provide automatic towel heater operation in both the morning and evening. For example, the 2x4H cycle will turn ON for 4 hours and then OFF for 8 hours on a continuous cycle. Decide when you want the towel rail to be ON, setting it at 6pm at night turns the appliance on from 6pm to 10pm and again from 6am to 10am Once the switch is turned ON the Envirotouch starts counting the ON hours immediately.

TO TURN ON Press button

OUTPUT ON

Press button again within

ON

3 seconds

Press button again within

ON

3 seconds

Press button again within

ON

3 seconds

Press button again within

ON

3 seconds

TO TURN OFF

Wait 3 seconds then

OFF

press button

CHANGE DEFAULT

Press button and hold for

OFF

5 seconds

Press button again within

OFF

3 seconds

Press button again within

OFF

3 seconds

Press button again within

OFF

3 seconds

Press button again within

OFF

3 seconds

Don't press the button

OFF

for 5 seconds

LIGHTS The 30 minute light will come ON and stay ON The 60 minute light will come ON and stay ON The 2x4H light will come ON and stay ON
The 2x6H light will come ON and stay ON
The 30 minute light will come ON and stay ON

FUNCTION Output will turn OFF after 30 minutes
Output will turn OFF after 60 minutes
Output will be ON for fours hours. It will turn OFF for 8 hours. It will then turn ON again for 4 hours. It repeats this cycle indefinitely. Output will be ON for six hours. It will turn OFF for 8 hours. It will then turn ON again for 6 hours. It repeats this cycle indefinitely. Output will turn OFF after 30 minutes

All lights go OFF

The output will stay OFF indefinitely

All lights flash ON, then go OFF
The 60MIN minute light will come ON and stay ON The 2x4H light will come ON and stay ON The 2x6H light will come ON and stay ON All 30MIN light go ON and stay ON All lights flash ON twice then go OFF

This will change the default for the first time the button is pushed. The factory setting is 30MIN for the first time the button is pushed The default will be changed to 60 minutes
The default will be changed to 2x4H
The default will be changed to 2x6H
The default will be changed to ON indefinitely
The default program will be exited

6

SAFETY
Independent laboratory testing has confirmed Thermofilm's full compliance with Australian and other International Standards. This includes AS/NZ. The fixed wiring must be installed by a licensed electrician in accordance with the relevant local wiring regulations. This appliance is not intended for use by persons (including children) with reduced physical, sensory or intellectual capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance. If installed in wet areas, the switches must be located so that they cannot be touched by persons in the bath or shower.
MAINTENANCE
It is recommended that you dean your Envirotouch Wall Controller. With a soft cloth, gently wipe the surfaces of the controller with a mild detergent to remove the built up contaminants from the environment. Then with a clean cloth ensure all detergent is removed. Do not use any abrasive materials or products to clean the switch, this includes solvents, citrus based cleaners or other harsh cleaning products.
7

WARRANTY TERMS & CONDITIONS

The below Warranty Terms and Conditions apply for New Zealand and Australia only.

Thermofilm warrants to the original owner that the EnvirotouchTM product will be free from defects in materials and workmanship for a period of 12 months from the date of purchase in accordance with the following warranty terms and conditions.

Provision of this warranty is subject to:



The envirotouchTM product must be installed in accordance with the Installation Instructions and relevant

electrical standards and codes.



The envirotouchTM product must be maintained and cleaned according to instructions detailed in the Installa-

tion Manual.



There is no warranty expressed or implied with regard to capacity requirements. The selection of the unit or

units depends entirely upon the system design and capacities as determined by the purchaser.



The customer has not repaired, opened or altered the product in any unauthorised manner.



This warranty excludes damage to the product or components arising from circumstances outside the control

of Thermofilm, including, but not limited to, where the product is not used for intended purpose; where the

product has been rectified in any way; incorrect installation; incorrect power supply; damaged caused during

delivery; misapplication, misuse, abuse, vandalism, lack of maintenance or accident.



Thermofilm's obligations under this warranty are limited to repair or replacement at Thermofilm's factory of

any components of the product which Thermofilm identifies to its satisfaction to be defective.



Transportation charges involved in return of the product to the Thermofilm factory (or any other location

authorised in writing by Thermofilm) is the sole responsibility of the customer.



All products are inspected and tested before despatch and are at the risk of the purchaser after the shipment

from the Thermofilm factory, if not delivered by Thermofilm to destination.



No products or components will be supplied in advance of an examination of the faulty product or compo-

nents by Thermofilm or an authorized representative of Thermofilm.



Thermofilm does not participate in any site related costs or labour expenses incidental to replacement of

parts, repairing, removing, installing, servicing, transportation or handling of parts to complete products, and

assumes no liability on parts repaired or replaced without written authorisation. Thermofilm shall not be

liable for any default or delay in performance of its warranty obligations caused by any circumstances beyond

its control, including, but not limited to, judicial or government restrictions, strikes, fires, floods, abnormal

weather conditions, delayed supply of components.

Should products be determined as damaged on arrival, immediately notify the transport company of the condition and have them noted on the freight documents. If damage is discovered after unpacking, demand immediate inspection by the transportation company and insist that a record of the damage is made on the freight documentation.

The customer warrants using the product in accordance with:



Any instructions provided to it by Thermofilm from time to time.



All government and local regulations, including but not limited to all relevant electrical, environmental laws

and regulations governing the installation, storage, use, handling and maintenance of the goods.



All necessary and appropriate precautions and safety measures relating to the installation, storage, use, han-

dling and maintenance of goods.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

All warranty requests for repairs or replacements must be accompanied by a complete "Warranty Claim Form" available from Thermofilm, together with proof of purchase (and where possible, photos of the installation) and the heater returned to the place of purchase.

In the event of a warranty claim, the goods need to be returned to the distributor/retailer for repair/replacement. Contact

Thermofilm Australia Pty Ltd

17 Johnston Court, Dandenong South, Victoria 3175, Australia

Telephone: (03) 9562 3455, Fax: (03) 9548 3979

Email: [email protected]

8

www.thermofilm.com.au


Microsoft Publisher 2013

Search Any Device: