296654-37730 Ultronic S W de en fr nl cs pl ru hu
ULTRONICS - Stiebel Eltron - User Manual
User Manual for ULTRONICS
ULTRONICW - Stiebel Eltron - User Manual
User Manual for ULTRONICW
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 14 Pages, 3.43MB
Document DEVICE REPORTULTRONICW-Stiebel-Eltron-User-ManualBedienung und Installation Operation and installation Utilisation et installation Bediening en installatie Obsluha a instalace Obsluga i instalacja Használati és telepítési útmutató Händetrockner | Hand dryer | Sèche-mains | Handendroger | Osoucec rukou | Suszarka do rk | | Kézi szárító »» Ultronic S »» Ultronic W Contents | special information Special Information Operation 1. General information 13 1.1 Safety instructions 13 1.2 Other symbols in this documentation 13 1.3 Information on the appliance 13 1.4 Units of measurement 13 2. Safety 13 2.1 Intended use 13 2.2 General safety instructions 13 2.3 Safety clearances 14 2.4 CE designation 14 2.5 Test symbols 14 3. Appliance description 14 4. Operation 14 5. Cleaning, care and maintenance 14 6. Troubleshooting 14 Installation 7. Safety 15 7.1 General safety instructions 15 7.2 Regulations, standards and instructions 15 8. Preparations 15 8.1 Installation wall 15 8.2 Installation in bathrooms 15 8.3 Minimum clearances 15 9. Installation 16 9.1 Dismantling the casing cover 16 9.2 Wall mounting 16 9.3 Power supply 17 9.4 Assembling the casing cover 17 10. Handover 17 11. Specification 18 11.1 Wiring diagram 18 11.2 Minimum clearances and detection range 18 11.3 Guidelines for installation height 18 11.4 Dimensions and connections 19 11.5 Data table 19 Warranty Environment and recycling Special Information -- The appliance may be used by children aged 8 and up and persons with reduced physical, sensory or mental capabilities or a lack of experience provided that they are supervised or they have been instructed on how to use the appliance safely and have understood the resulting risks. Children must never play with the appliance. Children must never clean the appliance or perform user maintenance unless they are supervised. 12|Ultronic S/W www.stiebel-eltron.com Operation General information ENGLISH Operation 1. General information The chapter "Operation" is intended for appliance users and heating contractors. The chapter "Installation" is intended for heating contractors. Note Read these instructions carefully before using the appliance and retain them for future reference. Pass on the instructions to a new user if required. 1.1 Safety instructions 1.1.1 Structure of safety instructions KEYWORD Type of risk Here, possible consequences are listed that may result from failure to observe the safety instructions. ffSteps to prevent the risk are listed. Symbol ! Damage to the appliance and environment Appliance disposal ffThis symbol indicates that you have to do something. The action you need to take is described step by step. 1.3 Information on the appliance Symbol Appliance disposal Appliances with this marking are not suitable for general waste disposal, and should therefore be collected and disposed of separately. 1.4 Units of measurement Note All measurements are given in mm unless stated otherwise. 2. Safety 1.1.2 Symbols, type of risk Symbol ! Type of risk Injury Electrocution Fire 2.1 Intended use The appliance is used to dry wet hands. This appliance is designed for domestic use. It can be used safely by untrained persons. The appliance can also be used in a nondomestic environment, e.g. in a small business, as long as it is used in the same way. Any other use beyond that described shall be deemed inappropriate. Observation of these instructions and of instructions for any accessories used is also part of the correct use of this appliance. 2.2 General safety instructions 1.1.3 Keywords KEYWORD DANGER WARNING CAUTION Meaning Failure to observe this information will result in serious injury or death. Failure to observe this information may result in serious injury or death. Failure to observe this information may result in nonserious or minor injury. 1.2 Other symbols in this documentation Note General information is identified by the symbol shown on the left. ffRead these texts carefully. WARNING Electrocution Never insert any objects into apertures in the appliance. WARNING Fire Never operate this appliance -- in rooms where the appliance is at risk from fire or explosion as a result of chemicals, dust, gases or vapours. -- in the direct proximity of pipes or receptacles that carry or contain flammable or explosive materials. -- if work such as laying cables, grinding or sealing is carried out in the installation room. -- if naphtha, sprays, floor polish or similar products are handled. Ensure the room is adequately ventilated before using the appliance. WARNING Combustion Never place any flammable, combustible or insulating objects or materials, such as laundry, blankets, magazines, containers with floor polish or naphtha, spray cans or similar on the appliance or in direct proximity to it. www.stiebel-eltron.com Ultronic S/W|13 Operation Appliance description WARNING Electrocution Never lean any objects against the appliance or insert them between the appliance and the fixing wall. WARNING Injury ! The appliance may be used by children aged 8 and up and persons with reduced physical, sensory or mental capabilities or a lack of experience provided that they are supervised or they have been instructed on how to use the appliance safely and have understood the resulting risks. Children must never play with the appliance. Children must never clean the appliance or perform user maintenance unless they are supervised. Never cover the appliance Never cover the appliance to prevent overheating of the appliance. Note If the appliance is installed in rooms where flue gas, oil or petrol vapours occur or where work involves solvents and chemicals, the operation of the appliance can result in long-lasting nuisance through odours or contamination of the appliance. 2.3 Safety clearances ! Damage to the appliance and environment Maintain the required minimum clearances. The appliance's air inlet and outlet must not be obstructed by any objects. The minimum clearances of the appliance can be found in chapter "Specification / Minimum clearances and detection range". 4. Operation ffShake your wet hands over the sink before drying to reduce the drying time. ffHold your hands under the air outlet and rub them together in the air current. Note The IR sensor response area is located approx. 3-4 cm below the air outlet. More information on the detection range of the IR sensor can be found in chapter "Specification / Minimum clearances and detection range". 5. Cleaning, care and maintenance ! Damage to the appliance and environment Never spray the appliance using a water hose or other tools. This would let water penetrate the appliance. A damp cloth is sufficient for cleaning the casing. Never use abrasive or corrosive cleaning agents. Go over with a soft cloth if required. 6. Troubleshooting Problem The appliance does not start. Cause Remedy No power supply Check whether a fuse or RCD has blown or tripped in your fuse box. Covering the optical proximity Check whether the sensor sursensor impairs the function of face is clear. Once you have rethe appliance. In this case, the moved any objects, the appliappliance stops after approx. ance will work correctly again. 3 seconds to avoid constant operation. 2.4 CE designation The CE designation shows that the appliance meets all essential European requirements: -- Low Voltage Directive -- Electromagnetic Compatibility Directive The maximum permissible mains impedance is indicated in chapter "Specification". If you cannot remedy the fault, notify your contractor. To facilitate and speed up your enquiry, please provide the serial number from the type plate (000000-0000-000000). The type plate is located at the bottom of the appliance. 2.5 Test symbols See type plate. 3. Appliance description The appliance works without contact. If you hold your hands in the IR sensor detection range, the appliance fan is automatically enabled. Heated air is discharged from the appliance at high speed. Any moisture left on your hands is removed and your hands are dried. When you move your hands away from the IR sensor detection range, the appliance stops automatically after approx. 3 seconds. 14|Ultronic S/W www.stiebel-eltron.com 2250 3000 ENGLISH 26_07_31_0167 Installation Safety Installation 7. Safety Only a qualified contractor should carry out installation, commissioning, maintenance and repair of the appliance. 8.2 Installation in bathrooms WARNING Electrocution Install the appliance exclusively outside safety zone 2. 7.1 General safety instructions We guarantee trouble-free operation and operational reliability only if the original accessories and spare parts intended for the appliance are used. 600 1 3 2 0 7.2 Regulations, standards and instructions 600 WARNING Electrocution Carry out all electrical connection and installation work in accordance with relevant regulations. WARNING Electrocution Only use a permanent connection to the power supply. The appliance must be able to be separated from the power supply by an isolator that disconnects all poles with at least 3 mm contact separation. ! Damage to the appliance and environment Observe the type plate. The specified voltage range must match the mains voltage. Note Observe all applicable national and regional regulations and instructions. 8. Preparations 0 Safety zone 0 1 Safety zone 1 2 Safety zone 2 3 Safety zone 3 ffEnsure that you maintain the safety clearances of safety zone 2 towards bath tubs and shower cubicles. 8.3 Minimum clearances 127 8.1 Installation wall 40 130 300 Note Observe the information in chapter "Operation / Safety". Always install the appliance on a vertical wall. The back panel of the appliance must be flush with the wall to ensure that the appliance cannot be pulled off. ffEnsure that the wall on which the appliance is mounted is solid and has no recesses. ffPrior to installing the appliance, ensure the minimum permissible clearances to adjacent objects are observed. ffEnsure that the ambient air can enter the inlet on the bottom of the appliance without obstruction. ffEnsure that the air can escape from the appliance without obstruction. D0000019937 www.stiebel-eltron.com Ultronic S/W|15 Installation Installation 9. Installation 9.1 Dismantling the casing cover 9.1.2 Removing the casing cover 2. 3. 1. 26_07_32_0046 ffUndo the 2 internal torx screws with a torx screwdriver 25, turning it clockwise as far as it will go. The torx screws are rotated into the casing and remain in the casing. 9.1.1 Connecting the appliance back panel and casing cover Note The casing cover has 2 internal fixing eyes at the top, which are hooked into place in the 2 hooks on the appliance back panel. 1 2 26_07_32_0047 ffDetach the casing cover from the appliance at the bottom. ffLift the casing cover up until the cover's fixing eyes have come free of the hooks on the appliance back panel. ffPull the casing cover forwards to remove it from the appliance. 9.2 Wall mounting You can find a drilling template in the appendix to these instructions. ffWhen positioning the drilling template, be aware of the loca- tion and length of the power cable (see chapter "Electrical connections / Power cable"). ffUse our standard values as a guide for the installation height (see chapter "Specification / Standard values for the installation height"). ffUse suitable fixing screws and rawl plugs. lone für M ont a 26_07_32_0025 26_07_32_0041 1 Hook 2 Fixing eye ffCut out the drilling template and mark the 4 fixing points on the wall. ffDrill the 4 holes and insert rawl plugs. ffScrew the 2 lower fixing screws into the wall. 16|Ultronic S/W www.stiebel-eltron.com 26_07_32_0042 ENGLISH Installation Handover 9.3 Power supply WARNING Electrocution Only use a permanent connection to the power supply. The appliance must be able to be separated from the power supply by an isolator that disconnects all poles with at least 3 mm contact separation. 9.4 Assembling the casing cover 2. 1. 9.3.1 Power cable The length of the power cable must be at least 100 mm. The individual wires of the power cable must be stripped approx. 6.5 mm so they can be connected to the mains terminal. 9.3.2 Connecting the appliance 3. ffPush the casing cover on to the appliance from the front. ffPlace the top of the casing cover on the back panel of the appliance so that the fixing eyes lock under the hooks (see chapter "Dismantling the casing cover"). ffPress the bottom of the casing cover on to the appliance so that it clicks into place. 1 2 26_07_32_0043 1 Power cable 2 Cable entry ffPull the power cable through the cable entry in the back panel of the appliance. ffFit the appliance by placing the keyhole eyelets on to the fixing screws. ffSecure the appliance to the wall with the 2 upper fixing screws and then tighten the 2 lower screws. ffConnect the appliance to the power supply according to the wiring diagram (see chapter "Specification / Wiring diagram"). 26_07_32_0049 ffCheck that the casing cover is fitted correctly on the appliance. ffTighten the 2 internal torx screws with a torx screwdriver 25, turning it anti-clockwise as far as it will go. 10. Handover Explain the functions of the appliance to the user. Draw special attention to the safety instructions. Hand over these operating and installation instructions to the user. www.stiebel-eltron.com Ultronic S/W|17 Installation Specification 11. Specification 11.1 Wiring diagram 11.3 Guidelines for installation height Note Height (mm) indicates the clearance between the bottom of the appliance and the floor. Age Age Height (mm) Adult man 1350 85_07_32_0001 11.2 Minimum clearances and detection range 127 Adult woman Nursery school Primary school 40 130 300 1 High school 1250 4 - 7 810 7 - 10 910 10 - 13 1120 D0000019937 1 IR sensor detection range High school 13 - 16 1250 18|Ultronic S/W www.stiebel-eltron.com ENGLISH D0000019899 Installation Specification 11.4 Dimensions and connections 257 3 184 289 81 63 98 161 b01 b01 Entry electrical cables (view from the back of the appliance) 11.5 Data table Electrical details Power connection Frequency Rated voltage Rated current Rated output Max. mains impedance Zmax to DIN EN 61000-3-11 Dimensions Height Width Depth Weights Weight Versions Colour Casing material IP-Rating Protection class Values Operating noise Air velocity Air flow rate Drying time 234 17 192 Hz V A W Ohm mm mm mm kg dB(A) m/s m³/h s Ultronic S 231582 1/N/PE ~ 220-240V 50/60 230 4,0 910 257 289 257 234 4,4 Stainless steel Diecast aluminium IP24 I 82 94 200 15 Ultronic W 231583 1/N/PE ~ 220-240V 50/60 230 4,0 910 257 289 257 234 4,4 off white, RAL 9003 Diecast aluminium IP24 I 82 94 200 15 www.stiebel-eltron.com Ultronic S/W|19 Warranty | Environment and recycling Warranty The warranty conditions of our German companies do not apply to appliances acquired outside of Germany. In countries where our subsidiaries sell our products, it is increasingly the case that warranties can only be issued by those subsidiaries. Such warranties are only granted if the subsidiary has issued its own terms of warranty. No other warranty will be granted. We shall not provide any warranty for appliances acquired in countries where we have no subsidiary to sell our products. This will not affect warranties issued by any importers. Environment and recycling We would ask you to help protect the environment. After use, dispose of the various materials in accordance with national regulations. 20|Ultronic S/W www.stiebel-eltron.com Stiebel Eltron Warranty for Hand Dryers & Space Heaters Models HTE, ULTRONIC, CNS, CK & CK Z. Who gives the warranty 1. The warranty is given by Stiebel Eltron (Aust) Pty Ltd (A.B.N. 82 066 271 083) of 6 Prohasky Street, Port Melbourne, Victoria, 3207 ("we", "us" or "our"). The warranty 2. This warranty applies to Stiebel Eltron Hand Dryers and Space Heaters Models HTE 4, HTE 5, ULTRONIC, CNS 100, CNS 150, CNS 200, CNS 250, CK 20S and CKZ 20S (the "unit") manufactured after 1 May 2015. 3. Subject to the warranty exclusions we will repair or replace, at our absolute discretion, a faulty component in your unit free of charge if it fails to operate in accordance with its specifications during the warranty period. 4. If we repair or replace a faulty component to your unit under this warranty, the warranty period is not extended from the time of the repair or replacement. 8.7. The date of installation of the unit where appropriate; 8.8. A copy of the certificate of compliance when the unit was installed where appropriate. 9. The contact details for you to make your warranty claim are: Name: Address: Telephone: Contact person: E-mail: Stiebel Eltron (Aust) Pty Ltd 6 Prohasky Street, Port Melbourne, Victoria, 3207 1800 153 351 (8.00 am to 5.00 pm AEST Monday to Friday) Customer Service Representative [email protected] 10. We will arrange a suitable time with you to inspect and test the unit. Warranty exclusions 11. We may reject your warranty claim if: 5. The warranty period commences on the date of purchase of the unit. Where the date of purchase is not known, then the warranty period will commence 2 months after the date of manufacture. 11.1. The unit was not installed by registered and qualified tradespeople, where required. 11.2. The unit was not installed and commissioned: 6. The warranty period for a unit is shown in the table below. (a) in Australia; Component All components Warranty period 5 years from the date of purchase of the unit. (b) in accordance with the Operating and Installation Guide; and (c) in accordance with the relevant statutory and local requirements of the State or Territory in which the unit is installed. Your entitlement to make a warranty claim 7. You are entitled to make a warranty claim if: 11.3. The unit has not been operated or maintained in accordance with the Operating and Installation Guide. 7.1. you own the unit or if you have the owner's consent to represent the owner of the unit; 11.4. The unit does not bear its original Serial Number or Rating Label. 7.2. you contact us within a reasonable time of discovering the problem with the unit; 11.5. The unit was damaged by any or any combination of the following: How you make a warranty claim 8. To make a warranty claim you must provide us with the following information: 8.1. The model number of the unit; 8.2. A description of the problem with the unit; (a) normal fair wear and tear; (b) connection to an incorrect power supply; (c) connection to faulty equipment, such as faulty circuit breaker; 8.3. The name, address and contact details (such as phone number and e-mail address) of the owner; 8.4. The address where the unit is installed and the location (e.g. in living room); 8.5. The serial number of the unit; 8.6. The date of purchase of the unit and the name of the seller of the unit; (d) accidental damage; (e) act of God, including damage by flood, storm, fire, lightning strike and the like; (f) wiring not to AS3000 Standards 11.6. The unit was damaged before it was installed e.g. it was damaged in transit. 11.7. An unauthorised person has modified, serviced, repaired or attempted to repair the unit without our consent. 11.8. Non genuine parts other than those manufactured or approved by us have been used on the unit. 12. We may charge you: 12.1. for any additional transport costs if the unit is installed more than 30 kilometres from our closest authorised service technician. 12.2. for the extra time it takes our authorised service technician to access the unit for inspection and testing if it is not sited in accordance with the Operating and Installation Guide and not readily accessible for inspection. 12.3. for any extra costs of our authorised service technician to make the unit safe for inspection. 13. You must ensure that access to the unit by our authorised service technician is safe and free from obstruction. 14. Our authorised service technician may refuse to inspect and test the unit until you provide safe and free access to it, at your cost. 15. If we reject your warranty claim in accordance with clause 11, we may charge you for our authorised service technician's labour costs to inspect and test the unit. 16. In order to properly test the unit we may remove it to another location for testing. Australian Consumer Law 17. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 18. The Stiebel Eltron warranty for the unit is in addition to any rights and remedies you may have under the Australian Consumer Law. Deutschland STIEBEL ELTRON GmbH & Co. KG Dr.-Stiebel-Straße 33 | 37603 Holzminden Tel. 05531 702-0 | Fax 05531 702-480 [email protected] www.stiebel-eltron.de Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | [email protected] Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | [email protected] Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | [email protected] Australia STIEBEL ELTRON Australia Pty. Ltd. 6 Prohasky Street | Port Melbourne VIC 3207 Tel. 03 9645-1833 | Fax 03 9645-4366 [email protected] www.stiebel.com.au Austria STIEBEL ELTRON Ges.m.b.H. Eferdinger Str. 73 | 4600 Wels Tel. 07242 47367-0 | Fax 07242 47367-42 [email protected] www.stiebel-eltron.at Belgium STIEBEL ELTRON bvba/sprl 't Hofveld 6 - D1 | 1702 Groot-Bijgaarden Tel. 02 42322-22 | Fax 02 42322-12 [email protected] www.stiebel-eltron.be Czech Republic STIEBEL ELTRON spol. s r.o. K Hájm 946 | 155 00 Praha 5 - Stodlky Tel. 251116-111 | Fax 235512-122 [email protected] www.stiebel-eltron.cz Denmark Pettinaroli A/S Mandal Allé 21 | 5500 Middelfart Tel. 06341 666-6 | Fax 06341 666-0 [email protected] www.stiebel-eltron.dk Finland STIEBEL ELTRON OY Kapinakuja 1 | 04600 Mäntsälä Tel. 020 720-9988 [email protected] www.stiebel-eltron.fi France STIEBEL ELTRON SAS 7-9, rue des Selliers B.P 85107 | 57073 Metz-Cédex 3 Tel. 0387 7438-88 | Fax 0387 7468-26 [email protected] www.stiebel-eltron.fr Hungary STIEBEL ELTRON Kft. Gyár u. 2 | 2040 Budaörs Tel. 01 250-6055 | Fax 01 368-8097 [email protected] www.stiebel-eltron.hu Japan NIHON STIEBEL Co. Ltd. Kowa Kawasaki Nishiguchi Building 8F 66-2 Horikawa-Cho Saiwai-Ku | 212-0013 Kawasaki Tel. 044 540-3200 | Fax 044 540-3210 [email protected] www.nihonstiebel.co.jp Netherlands STIEBEL ELTRON Nederland B.V. Daviottenweg 36 5222 BH 's-Hertogenbosch Tel. 073 623-0000 | Fax 073 623-1141 [email protected] www.stiebel-eltron.nl Poland STIEBEL ELTRON Polska Sp. z o.o. ul. Dzialkowa 2 | 02-234 Warszawa Tel. 022 60920-30 | Fax 022 60920-29 [email protected] www.stiebel-eltron.pl Russia STIEBEL ELTRON LLC RUSSIA Urzhumskaya street 4, Slovakia TATRAMAT - ohrievace vody, s.r.o. Hlavná 1 | 058 01 Poprad Tel. 052 7127-125 | Fax 052 7127-148 [email protected] www.stiebel-eltron.sk Switzerland STIEBEL ELTRON AG Industrie West Gass 8 | 5242 Lupfig Tel. 056 4640-500 | Fax 056 4640-501 [email protected] www.stiebel-eltron.ch Thailand STIEBEL ELTRON Asia Ltd. 469 Moo 2 Tambol Klong-Jik Amphur Bangpa-In | 13160 Ayutthaya Tel. 035 220088 | Fax 035 221188 [email protected] www.stiebeleltronasia.com United Kingdom and Ireland STIEBEL ELTRON UK Ltd. Unit 12 Stadium Court Stadium Road | CH62 3RP Bromborough Tel. 0151 346-2300 | Fax 0151 334-2913 [email protected] www.stiebel-eltron.co.uk United States of America STIEBEL ELTRON, Inc. 17 West Street | 01088 West Hatfield MA Tel. 0413 247-3380 | Fax 0413 247-3369 [email protected] www.stiebel-eltron-usa.com building 2 | 129343 Moscow Tel. 0495 7753889 | Fax 0495 7753887 [email protected] 4<AMHCMN=jg fej> www.stiebel-eltron.ru Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve d`erreurs et de modifications techniques! | Onder voorbehoud van vergissingen en technische wijzigingen! | Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeone zmiany techniczne i ewentualne bldy | Omyly a technické zmny jsou vyhrazeny! | A muszaki változtatások és tévedések jogát fenntartjuk! | . . | Chyby a technické zmeny sú vyhradené! Stand 8845 A 296654-37730-8870Adobe InDesign CS6 (Windows) Adobe PDF Library 10.0.1