Are You suprised ?
Birthday
LSK
Test Report
Jiangmen Sinofan Lighting Appliances Co.,Ltd 20239TRF 2BKHN-20239TRF 2BKHN20239TRF 20239trf
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 22 Pages, 1.41MB
Document DEVICE REPORTGetApplicationAttachment.html?id=7634343Jiangmen Sinofan Lighting Appliances Co.,Ltd TEST REPORT SCOPE OF WORK EMC TESTING20239TRF REPORT NUMBER 240708055GZU-001 ISSUE DATE [REVISED DATE] 30-August-2024 [---------------------] PAGES 22 DOCUMENT CONTROL NUMBER FCC part 15.231 © 2017 INTERTEK TEST REPORT Room101/301/401/102/202/302/ 402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Telephone: +86 20 8213 9688 Facsimile: +86 20 3205 7538 www.intertek.com.cn Applicant Name & Address Manufacturing Site Intertek Report No: FCC ID: : Jiangmen Sinofan Lighting Appliances Co.,Ltd NO. 4F&5F, 5 Building, No.3 Huahui Road, Waihai Street, Jianghai District, Jiangmen City, 529000, Guangdong province, China : Same as applicant 240708055GZU-001 2BKHN-20239TRF Test standards CFR 47, FCC PART 15 Subpart C: 2023 section 15.231 Sample Description Product Model No. Electrical Rating Serial No. Date Received Date Test Conducted : Remote control : 20239TRF : DC 3V : Not Labeled : 08 July 2024 : 31 July 2024 Prepared and Checked By Approved By: Ace Yao Engineer Dean Liu Sr. Project Engineer This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China Version: 14 December 2022 Page 2 of 22 FCC Part 15.231 Intertek Report No.: 240708055GZU-001 TEST REPORT CONTENT TESTREPORT........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY............................................................................................ 4 2.0 GENERAL DESCRIPTION ............................................................................................. 5 2.1 PRODUCT DESCRIPTION........................................................................................................5 2.2 RELATED SUBMITTAL(S) GRANTS ...........................................................................................5 2.3 TEST METHODOLOGY ..........................................................................................................5 2.4 TEST FACILITY .....................................................................................................................5 3.0 SYSTEM TEST CONFIGURATION ................................................................................. 6 3.1 JUSTIFICATION ....................................................................................................................6 3.2 EUT EXERCISING SOFTWARE.................................................................................................7 3.3 SPECIAL ACCESSORIES ..........................................................................................................7 3.4 MEASUREMENT UNCERTAINTY ..............................................................................................7 3.5 EQUIPMENT MODIFICATION .................................................................................................8 3.6 SUPPORT EQUIPMENT LIST AND DESCRIPTION..........................................................................8 4.0 MEASUREMENT RESULTS .......................................................................................... 9 4.1 ANTENNA REQUIREMENT .....................................................................................................9 4.2 RADIATED EMISSIONS ........................................................................................................10 4.3 OCCUPIED BANDWIDTH .....................................................................................................19 4.4 DWELL TIME ....................................................................................................................20 5.0 TEST EQUIPMENT LIST............................................................................................. 22 Version: 14 December 2022 Page 3 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT 1.0 TEST RESULT SUMMARY Test Item Test Requirement Test Method Radiated Emission FCC PART 15 section 15.231(b) ANSI C 63.10: Clause 6.4, 6.5 and 6.6 Occupied Bandwidth FCC PART 15 section 15.231(c) ANSI C 63.10: Clause 6.9 Dwell Time FCC PART 15 section 15.231(a) FCC PART 15: Section 15.231(a) Remark: N/A: not applicable. Refer to the relative section for the details. EUT: In this whole report EUT means Equipment Under Test. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) means Receiver. RF: In this whole report RF means Radio Frequency. ANSI C63.10: the detail version is ANSI C63.10:2013 in the whole report Result PASS PASS PASS Version: 14 December 2022 Page 4 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT 2.0 General Description 2.1 Product Description Operating Frequency Type of Modulation: Number of Channels Channel Separation: Antenna Type Power Supply: Power cord: Function: 433.92 MHz ASK 1 Channel N/A PCB antenna DC 3V N/A Remote control with 433.92 MHz as carrier. 2.2 Related Submittal(s) Grants This is an application for certification of: DSC - Part 15 Security/Remote Control Transmitter 2.3 Test Methodology Radiated emission measurements was performed according to the procedures in ANSI C63.10. Radiated emission measurement was performed in semi-anechoic chamber and conducted emission measurement was performed in shield room. For radiated emission measurement, preliminary scans and final tests were performed in the semi-anechoic chamber to determine the worst case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters, unless stated otherwise. 2.4 Test Facility All tests were performed at: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China Except Conducted Emissions was performed at: Room101/301/401/102/202/302/402/502/602/702/802, No. 7-2, Caipin Road, Huangpu District, Guangzhou, Guangdong, China A2LA Certificate Number 0078.10 Version: 14 December 2022 Page 5 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT Intertek Testing Services Shenzhen Ltd. Guangzhou Branch is accredited by A2LA and Listed in FCC website. FCC accredited test labs may perform both Certification testing under Parts 15 and 18 and Declaration of Conformity testing. 3.0 System Test Configuration 3.1 Justification For emissions testing, the equipment under test (EUT) setup to transmit continuously to simplify the measurement methodology. Care was taken to ensure proper power supply voltages during testing. It was powered by DC 3V supply. When below 30MHz, the measurement antenna was positioned with its plane perpendicular to the ground at the specified distance. When perpendicular to the ground plane, the lowest height of the magnetic antenna was 1 m above the ground and was positioned at 3m distance from the EUT. During testing the loop antenna was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. For each measurement antenna alignment, the EUT shall be rotated through 0° to 360° on a turntable. When above 30MHz, the antenna height and polarization are varied during the search for maximum signal level. The antenna height is varied from 1 to 4 meters. Radiated emissions are taken at three meters unless the signal level is too low for measurement at that distance. If necessary, a pre-amplifier is used and/or the test is conducted at a closer distance. All readings are extrapolated back to the equivalent three meters reading using inverse scaling with distance. The spurious emissions more than 20 dB below the permissible value are not reported. For an intentional radiator, the spectrum shall be investigated from the lowest radio frequency signal generated in the device, without going below 9 kHz, up to at least the frequency shown in the following table: Frequency range of radiated emission measurements Lowest frequency generated in the device 9 kHz to below 10 GHz At or above 10 GHz to below 30 GHz At or above 30 GHz Upper frequency range of measurement 10th harmonic of highest fundamental frequency or to 40 GHz, whichever is lower 5th harmonic of highest fundamental frequency or to 100 GHz, whichever is lower 5th harmonic of highest fundamental frequency or to 200 GHz, whichever is lower, unless otherwise specified Number of fundamental frequencies to be tested in EUT transmit band Version: 14 December 2022 Page 6 of 22 FCC Part 15.231-f TEST REPORT Frequency range in which device operates 1 MHz or less 1 MHz to 10 MHz More than 10 MHz 3.2 EUT Exercising Software N/A 3.3 Special Accessories No special accessories used. Intertek Report No.: 240708055GZU-001 Number of frequencies 1 2 3 Location in frequency range of operation Middle 1 near top and 1 near bottom 1 near top, 1 near middle and 1 near bottom 3.4 Measurement Uncertainty No. Item Measurement Uncertainty 20 dB Bandwidth 1 6dB Bandwidth 2.3% 99% Bandwidth 2 Carrier Frequencies Separated 2.3% 3 Dwell Time 1.2% 4 Maximum Peak Conducted Output Power 1.5dB 5 Peak Power Spectral Density 1.5dB 6 Out of Band Conducted Emissions 1.5dB 7 Band edges measurement 1.5dB 4.7 dB (25 MHz-1 GHz) 8 Radiated Emissions 4.8 dB (1 GHz-18 GHz) 5.21dB (18GZH-26GHz) 9 Conducted Emissions at Mains Terminals 2.58dB 10 Temperature 11 Humidity 12 Time 0.5 °C 0.4 % 1.2% The measurement uncertainty describes the overall uncertainty of the given measured value during the operation of the EUT. Measurement uncertainty is calculated in accordance with ETSI TR 100 028-2001. The measurement uncertainty is given with a confidence of 95%, k=2. Version: 14 December 2022 Page 7 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT When determining of the test conclusion, the Measurement Uncertainty of test has been considered. Uncertainty and Compliance Unless the standard specifically states that measured values are to be extended by the measurement uncertainty in determining compliance, all compliance determinations are based on the actual measured value 3.5 Equipment Modification Any modifications installed previous to testing by Jiangmen Sinofan Lighting Appliances Co.,Ltd will be incorporated in each production model sold / leased in the United States. No modifications were installed by Intertek Testing Services Shenzhen Ltd. Guangzhou Branch. 3.6 Support Equipment List and Description The client made a continuous transmit sample for test, in actual use the product has duty cycle. Version: 14 December 2022 Page 8 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT 4.0 Measurement Results 4.1 Antenna Requirement Standard requirement: 15.203 requirement: For intentional device. According to 15.203. an intentional radiator shall be designed to Ensure that no antenna other than that furnished by the responsible party shall be used with the device. EUT Antenna The antenna is an integral antenna and no consideration of replacement. Version: 14 December 2022 Page 9 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 4.2 Radiated Emissions Test Requirement: FCC Part 15 C section 15.231(b) Test Method: ANSI C63.10: Clause 6.4, 6.5 and 6.6 Measurement Distance: Test Status: Test site: 3 m (Semi-Anechoic Chamber) Test the transmitter in continuous transmitting mode. Measurement Distance: 3m (Semi-Anechoic Chamber) Limit: The field strength of emissions from intentional radiators operated under this Section shall not exceed the following: Fundamental Frequency MHz Field Strength of Fundamental (dBµV/m @ 3 m) Field Strength of Harmonics and Spurious Emissions (dBµV/m @ 3 m) 40.66 to 40.70 67.04 47.04 70 to 130 61.94 41.94 130 to 174 61.94 to 71.48** 41.94 to 51.48** 174 to 260 71.48 51.48 260 to 470 71.48 to 81.94** 51.48 to 61.94** Above 470 81.94 61.94 ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130-174 MHz, uV/m at 3 meters = 56.81818(F) - 6136.3636; for the band 260-470 MHz, uV/m at 3 meters = 41.6667(F) 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] The fundamental frequency of the EUT is 433.92 MHz The limit for average or QP field strength dBuv/m for the fundamental emission= 80.8 dBµV/m No fundamental is allowed in the restricted bands. The limit for average field strength dBuv/m for the spurious emission=60.8 dBuV/m. Spurious Emissions do not fall in the restricted bands must be less than 60.8 dBuV/m or limits shown in Section 15.209, whichever limit permits a higher field strength. Spurious Emissions appear within the restricted bands shall not exceed the limits shown in Section 15.209. Field Strength Calculation: The field strength is calculated by adding the reading on the Spectrum Analyzer to the factors associated with preamplifiers (if any), antennas, cables, pulse desensitization and average factors (when specified limit is in average and measurements are made with peak detectors). A sample calculation is included below: FS = RA + AF + CF - AG + PD + AV FS = RA + Correct Factor + AV Version: 14 December 2022 Page 10 of 22 FCC Part 15.231-f TEST REPORT Where: Intertek Report No.: 240708055GZU-001 FS = Field Strength in dBµV/m RA = Receiver Amplitude (including preamplifier) in dBµV AF = Antenna Factor in dB/m CF = Cable Attenuation Factor in dB AG = Amplifier Gain in dB PD = Pulse Desensitization in dB AV = Average Factor in dB Correct Factor = AF + CF AG + PD In the radiated emission table which follows, the reading shown on the data table may reflect the preamplifier gain. An example of the calculations, where the reading does not reflect the preamplifier gain, follows: FS = RA + AF + CF - AG + PD + AV Assume a receiver reading of 62.0 dBµV is obtained. The antenna factor of 7.4 dB/m and cable factor of 1.6 dB is added. The amplifier gain of 29 dB is subtracted. The pulse desensitization factor of the spectrum analyzer was 0 dB, and the resultant average factor was -10 dB. The net field strength for comparison to the appropriate emission limit is 32 dBµV/m. RA = 62.0 dBµV AF = 7.4 dB/m CF = 1.6 dB AG = 29.0 dB PD = 0 dB AV = -10 dB Correct Factor = 7.4 + 1.6 29.0 + 0 = -20 dB/m FS = 62 + (-20) + (-10) = 32 dBµV/m Version: 14 December 2022 Page 11 of 22 FCC Part 15.231-f TEST REPORT Test Configuration: 1) 9 kHz to 30 MHz emissions: Intertek Report No.: 240708055GZU-001 2) 30 MHz to 1 GHz emissions: Version: 14 December 2022 Page 12 of 22 FCC Part 15.231-f TEST REPORT 3) 1 GHz to 40 GHz emissions: Intertek Report No.: 240708055GZU-001 Test Procedure: 1) 9 kHz to 30 MHz emissions: For testing performed with the loop antenna. The lowest of the loop was positioned 1 m above the ground and positioned with its plane vertical at the special distance from the EUT. During testing the loop was rotated about its vertical axis for maximum response at each azimuth and also investigated with the loop positioned in the horizontal plane. 2) 30 MHz to 1 GHz emissions: For testing performed with the bi-log type antenna. The measurement is performed with the EUT rotated 360º, the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurement for both the horizontal and vertical antenna polarizations. 3) 1 GHz to 40 GHz emissions: Test site with RF absorbing material covering the ground plane that met the site validation criterion called out in CISPR 16-1-4:2010 was used to perform radiated emission test above 1 GHz. For testing performed with the horn antenna. The measurement is performed with the EUT rotated 360º, the antenna height scanned between 1m and 4m, and the antenna rotated to repeat the measurement for both the horizontal and vertical antenna polarizations. Version: 14 December 2022 Page 13 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT Detector: For Peak and Quasi-Peak value: RBW = 1 MHz for f 1 GHz, 200 Hz for 9 kHz to 150 kHz 9 kHz for 150 kHz to 30 MHz 120 kHz for 30 MHz to 1GHz VBW RBW Sweep = auto Detector function = peak for f 1 GHz, QP for f < 1 GHz Trace = max hold For AV value: Average = Peak value + 20log (Duty cycle) The average correction factor is computed by analyzing the on time in 100ms over one complete pulse train. Analysis of the remote transmitter on time in one complete pulse train, therefore the average value of fundamental frequency is: Average = Peak value + 20log (Duty cycle), where the duty factor is calculated from following formula: The duration of one cycle =54.203ms Effective period of the cycle =(1.087x25+0.3623x8) ms=30.0734 ms DC =30.0734/54.203=0.5548 or 55.48% Therefore, the averaging factor is found by 20lg0.5548=-5.1 Please refer to below plots for more details. Date: 24.JUL.2024 07:13:31 Version: 14 December 2022 Page 14 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 Date: 24.JUL.2024 07:14:49 Date: 24.JUL.2024 07:16:21 Version: 14 December 2022 Page 15 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 Date: 24.JUL.2024 07:16:48 Date: 24.JUL.2024 07:17:11 Version: 14 December 2022 Page 16 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 Used Test Equipment List: 3m Semi-Anechoic Chamber, EMI Test Receiver (9 kHz~7 GHz), Signal and Spectrum Analyzer (10 Hz~40 GHz), Loop antenna (9 kHz-30 MHz). TRILOG Super Broadband test Antenna(30 MHz3 GHz(RX), Bouble-Ridged Waveguide Horn Antenna (800 MHz-18 GHz)(RX) and High Frequency Antenna & preamplifier(18 GHz~26.5 GHz) (RX). Refer to Clause 5 Test Equipment List for details. 1) Fundamental emission: Polarization Horizontal Vertical Frequency (MHz) 433.90 433.90 PK Reading (dBuV) 55.9 42.6 Correction Factor(dB) 18.3 18.3 PK value (dBuV/m) 74.2 60.9 PK limit (dBuV/m) 100.8 100.8 Result Pass Pass Polarization Horizontal Vertical Frequency (MHz) 433.90 433.90 PK value (dBuV/m) 74.2 60.9 Average Factor(dB) -5.1 -5.1 AV value (dBuV/m) 69.1 55.8 AV limit (dBuV/m) 80.8 80.8 Result Pass Pass 1. Corr. (dB/m) = Antenna Factor (dB/m) + Cable Loss (dB) 2. Level (dBV/m) = Corr. (dB/m) + Read Level (dBV/m) 3. Margin (dB) = Limit Line (dBV/m) Level (dBV/m) 2) other emissions: The receiver was scanned from the lowest frequency generated within the EUT to 5 GHz. The field strength is calculated by adding the Antenna Factor, Cable Factor & Peramplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor Peramplifier Factor. The following test results were performed on the EUT. If the peak emission level is lower than the average limit, the average emission level does not need to show. Test the EUT in transmitting mode: 9 kHz~30 MHz Field Strength of Unwanted Emissions. Peak or Quasi-Peak measurement. The measurements with active loop antenna were greater than 20dB below the limit, so the test data were not recorded in the test report. Version: 14 December 2022 Page 17 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT 30 MHz~5 GHz Field Strength of Unwanted Emissions. Peak or Quasi-Peak measurement: Horizontal. Polarization Frequency (MHz) Horizontal Horizontal Vertical Vertical 867.89 2603.13 867.89 3586.25 PK Reading (dBuV) 24.2 51.4 14.2 45.0 Correction Factor(dB) 25.7 -7.4 25.7 -3.8 PK value (dBuV/m) 49.9 44.0 39.9 41.2 PK limit (dBuV/m) 80.8 80.8 80.8 80.8 Result Pass Pass Pass Pass Polarization Horizontal Horizontal Vertical Vertical Frequency (MHz) 867.89 2603.13 867.89 3586.25 PK value (dBuV/m) 49.9 44.0 39.9 41.2 Average Factor(dB) -5.1 -5.1 -5.1 -5.1 AV value (dBuV/m) 44.8 38.9 34.8 36.1 AV limit (dBuV/m) 60.8 60.8 60.8 60.8 Result Pass Pass Pass Pass Remark: According to 15.35 (b) When average radiated emission measurements are specified in the regulations, including emission measurements below 1000 MHz, there is also a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit for the frequency being investigated unless a different peak emission limit is otherwise specified in the rules, e.g., see Section 15.255. Version: 14 December 2022 Page 18 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 4.3 Occupied Bandwidth Test Requirement: FCC Part 15 C section 15.231 (c) Test Method: ANSI C63.10: Clause 6.9 Test Status: Test in transmitting mode at lowest and highest channel. Requirements: 15.231 (c) The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70 MHz and below 900 MHz. For devices operating above 900 MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. Method of measurement: The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. Record the 20 dB bandwidth of the carrier. Used Test Equipment List: Spectrum Analyzer. Refer to Clause 5 Test Equipment List for details. Test result: Test Channel bandwidth 433.92 MHz 5.174 kHz Remark: The bandwidth limit is 433.92 x 0.0025 = 1.08 MHz Test plot: Limit 1.08 MHz Date: 1.AUG.2024 14:05:49 Version: 14 December 2022 Page 19 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 4.4 Dwell Time Test Requirement: FCC Part 15 C section 15.231(a) Test Method: FCC Part 15 C section 15.231(a) Test Status: Requirements: Test in transmitting mode. 1. Regulation 15.231 (a) The provisions of this Section are restricted to periodic operation within the band 40.66 40.70 MHz and above 70 MHz. Except as shown in paragraph (e) of this Section, the intentional radiator is restricted to the transmission of a control signal such as those used with alarm systems, door openers, remote switches, etc. Radio control of toys is not permitted. Continuous transmissions, such as voice or video, and data transmissions are not permitted. The prohibition against data transmissions does not preclude the use of recognition codes. Those codes are used to identify the sensor that is activated or to identify the particular component as being part of the system. Result: The EUT is a remote switch without audio or video transmitted. The EUT meets the requirements of this section. 2. Regulation 15.231 (a1) A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. Result: Carrier Frequency Shutdown Time Limit 433.92MHz 0.3192s 5s Result plot as follows: Version: 14 DDeactee:m2b4.eJrU2L.0220224 07:19:10 Page 20 of 22 FCC Part 15.231-f TEST REPORT Intertek Report No.: 240708055GZU-001 3. Regulation 15.231 (a2) A transmitter activated automatically shall cease transmission within 5 seconds after activation. Result: The EUT does not have automatic transmission. 4. Regulation15.231 (a3) Periodic transmissions at regular predetermined intervals are not permitted. However, polling or supervision transmissions to determine system integrity of transmitters used in security or safety applications are allowed if the periodic rate of transmission does not exceed one transmission of not more than one second duration per hour for each transmitter. Result: The EUT does not employ periodic transmission. 5. Regulation 15.231 (a4) Intentional radiators which are employed for radio control purposes during emergencies involving fire, security, and safety of life, when activated to signal an alarm, may operate during the pendency of the alarm condition. Result: This section is not applicable to the EUT. Version: 14 December 2022 Page 21 of 22 FCC Part 15.231-f Intertek Report No.: 240708055GZU-001 TEST REPORT 5.0 Test Equipment List Radiated Emission/Radio Equipment No. Equipment Model EM030-04 EM031-02 3m Semi-Anechoic Chamber 9×6×6 m3 EMI Test Receiver (9 kHz~7 GHz) R&S ESR7 Manufacturer ETS LINDGRE N R&S Cal. Due date Calibration (YYYY-MM-DD) Interval 2025-04-09 1Y 2024-11-15 1Y EM031-03 Signal and Spectrum Analyzer (10 Hz~40 GHz) R&S FSV40 R&S 2024-11-12 1Y EM011-04 Loop antenna (9 kHz-30 MHz) HFH2-Z2 R&S 2025-07-07 1Y TRILOG Super Broadband test EM033-01 Antenna(30 MHz-3 GHz(RX) VULB 9163 SCHWARZBECK 2024-12-05 1Y EM033-02 EM033-03 EM033-04 Bouble-Ridged Waveguide Horn Antenna (800 MHz-18 GHz)(RX) R&S HF907 R&S High Frequency Antenna & preamplifier(18 GHz~26.5 GHz) R&S SCU-26 R&S (RX) High Frequency Antenna & preamplifier (26 GHz-40 GHz) R&S SCU-40 R&S 2025-07-02 1Y 2025-04-22 1Y 2025-04-22 1Y EM031-02-01 Coaxial cable(9 kHz-1 GHz) N/A R&S 2025-04-09 1Y EM033-02-02 Coaxial cable(1 GHz-18 GHz) N/A R&S 2025-04-09 1Y EM033-04-02 Coaxial cable(18 GHz~40 GHz) N/A R&S 2025-04-25 1Y EM031-01 Signal Generator (9 kHz~6 GHz) SMB100A R&S 2025-03-17 1Y EM040-01 Band Reject/Notch Filter WRHFV Wainwright N/A 1Y EM040-02 Band Reject/Notch Filter WRCGV Wainwright N/A 1Y EM040-03 Band Reject/Notch Filter WRCGV Wainwright N/A 1Y EM022-03 2.45 GHz Filter BRM50702 Micro-Tronics 2025-05-15 1Y SA016-29 Climatic Test Chamber MHU-80L JIANQIAO 2025-01-03 1Y EM046-05 Power meter EM046-06 Power meter EM045-01-01 EMC32 software (RE/RS) NPR6A R&S NPR6A R&S V10.01.00 R&S 2025-04-22 1Y 2025-05-09 1Y N/A N/A *C*o*n*d*u*ct*e*d**D*i*s*t*u*r*b*a*n*c*e-*M*a*i*n*s**T*e*r*m*i*naEln(d1o)f the test report****************************** Cal. Due date Calibration Equipment No. Equipment Model Manufacturer (DD-MM-YYYY) Interval EM080-05 EMI receiver ESCI R&S 06/06/2025 1Y EM006-05 SA047-112 EM004-04 LISN Digital Temperature-Humidity Recorder EMC shield Room ENV216 RS210 8m×3m×3m R&S YIJIE Zhongyu 04/06/2025 1Y 22/10/2024 1Y 03/01/2025 1Y Conducted Disturbance-Mains Terminal(2) Equipment No. Equipment Model EM031-04 EMI receiver ESR3 EM006-06 SA047-111 EM004-03 LISN Digital Temperature-Humidity Recorder EMC shield Room ENV216 RS210 8m×4m×3m VeErMsio0n3:1-1044D-0e1cemEMbeCr3220s2o2ftware (CE) Page 22 oVf 2120.01.00 Cal. Due date Calibration Manufacturer (DD-MM-YYYY) Interval R&S 04/01/2025 1Y R&S 04/09/2024 1Y YIJIE 22/10/2024 1Y Zhongyu R&S 03/01/2025 1Y N/A FCC P1aYrt 15.231-f
Related FCC IDs:
- 2BKHN-20239TRF - Jiangmen Sinofan Lighting Appliances Co.,Ltd Remote control [-20239TRF] Microsoft Word for Microsoft 365; modified using iText 5.5.13 ©2000-2018 iText Group NV (AGPL-version)