User Manual
Turnils North America AMPWSSUV2 Wall Switch 2AU29AMPWSSUV2 2AU29AMPWSSUV2 ampwssuv2
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 2 Pages, 5.74MB
Document DEVICE REPORTGetApplicationAttachment.html?id=6241185Declarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Quick Index Settings 1 Pairing 2 Switch Rotating Direction 3 Setting Upper & Lower Limits Steps P1 (hold down for 2s) > Stop (hold down for 2s) Up + Down (hold down for 2s) Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s) Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s) 4 Add / Remove Favorite Position P2 > Stop > Stop 5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop 6 Adjust Limits Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s) Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s) 7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new) 8 Speed Regulation Acceleration: P2 > Up > Up Deceleration: P2 > Down > Down Troubleshooting Issues Possible Causes Battery in motor is depleted Insufficient charging from Solar PV Panel Wall switch battery is discharged Battery is inserted incorrectly into wall switch The motor has no response Radio interference / shielding Receiver distance is too far from wall switch Power failure Incorrect wiring Motor beeps 10 times when in use Battery voltage is low / PV (solar panel issue) Cannot program a single motor (multiple motors respond) Multiple motors are paired to the same channel. Solution Recharge with compatible AC adaptor and check connection and positioning of solar PV panel Check connection and orientation of solar PV panel Replace battery Check battery polarity Ensure wall switch and the antenna on the motor are positioned away from metal objects Move wall switch to a closer position Check power supply to motor is connected and active Check that wiring is connected correctly (refer to motor installation instructions) Recharge with AC adapter or check connection and positioning of solar PV panel Always reserve an individual channel for programming functions SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes Place all other motors into sleep mode (Press "P1" button (about 6 sec) on the motor head until motor jog x2 and beep x2). AMPTM Surface Mounted Wall Switch Fields of Application Roller Sheer Banded Roman Cellular/Honeycomb Cellular/Honeycomb Standard Skylight Specifications Tilt-Only Horizontal Narrow Width Voltage Radio Frequency Transmitting Power Operating Temperature RF Modulation Lock Function IP Rating Transmission Distance 3V (CR2430) 433.92 MHz Bi-directional 10 milliwatt 14°F to 122°F (-10°C to 50°C) FSK Yes IP20 up to 200m (outdoor) Safety Instructions 1. Do not expose motor to humid, damp, or extreme temperature conditions. 2. Do not drill into motor. 3. Do not cut Declarations the antenna. KAMeePp25iBt clear from metal objects. ChargingInstructions Micro-USB Port 4. Do not allow children to pInsltaruyctiown ith this device. Add A zoom in on the charging port 5. 6. LED light Features P1 button If the power cable or connector is damaged, do not use. LithiumBatterySwitch This motor has a built in Li-ion battery pack with integrated charge management. Max power input for recharging: 5V 2A. Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) . Fields of Application During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and Ensure the correct crown and drive adaptor are used.needstobecharged. During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped running and needed to be recharged. Rechargeable Battery 7. Ensure the FCC Text - textp01ower cable and aerial is clear Roller Sheer Revolve Romanshades and protected from moving parts. Specifications Blinking red: 8. Cable routed through walls should be properly isolated. Workingtemperature:-10~+50 Radio Frequency: 433.925MHz Low battery alert Input Voltage: USB 5V 1A / USB 5V 2A Maximum Running Time: 6 minutes 9. The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades. Following data for reference Motor is to be mounted in horizontal position only. Model Rated Torque (N.m) Rated Speed (rpm) Rated Power (W) P1 Button Instructions Blinking green: Charging is processing Solid green: Battery has finished charging. AMP25B - 0.7/34 0.7 34 8 10. Before installation, remove unnecessary AMP25B-1.1/28 1.1 28 cords8 and disable equipment not needed for powered operation. Add visual explanation of P1 - file 02 Attention 11. Installation and programming should be performed by a qualified professional. Use or modification outside the Neverdrop,knock,drillorsubmergethemotor.Keepthepowercableinrightpositionasfollowing. Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturer's liability and warranty. scope of these instructions may void warranty. -1Safety 1. Do not expose motor to humid, damp or extreme temperature conditions. 2. Do not drill into motor. 3. Do not cut the antenna and keep it clear from metal objects. 4. Do not allow children to play with this device. Do not dispose of in general waste. 5. If power cable or connector is damaged, do not use. 6. Ensure correct crown and drive adaptor are used. 7. Ensure power cable and aerial is clear and protected from moving parts. 8. Cable routed through walls shall be properly isolated. 9. Motor is to be mounted in horizontal position only. Please recycle batteries and damaged electrical products appropriately. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. 11. Installation and programming to be performed by a qualified professional, use or modification outside the scope of this instruction may void warranty. -2- Please scan QR code to see more AMPTM product information Button Instructions Up Up LowLeor wCehranCnhealnnel StopStop LCDLDCiDspDlaisyplay P2 P2 DowDnown HighHeirgChehranCnhealnnel P2 P2 GrouGproCuopntCrolntrol P1 Button LED light Power line AMPTILT P1 button Lithium Battery Switch Signal line P1 Button AMP25B / AMP28B / AMP35B / AMP25BDC AMPCEL Replace/Install CR2430 Battery a. Unlock the battery cover and take the cover out. a. b. Install battery (CR2430) with positive (+) side facing up. c. Gently put the cover back and switch to lock position. b. c. Advanced Setting - Disable Limit Setting a. Press and hold "Stop" button more than 15s. Wall Switch will show "L" (lock). b. In the next 10s, press one "P2" button on the back of Wall Switch. Wall Switch will show "o", then the Wall Switch switches to "Lock" mode to disable the following commands: - Change Motor Direction - Setting the Upper and Lower Limit - Adjust Limit - Roller Mode or Sheer Mode a. Action on Wall Switch Stop Wall Switch Response Action on Wall Switch b. P2 Button c. Press and hold "Stop" button more than 15s. Wall Switch will show "U" (unlock). d. In the next 10s, press one "P2" button on the back of Wall Switch. Wall Switch will show "o". The Wall Switch now switches to "Unlock" mode, you can access all control functions. Wall Switch Response c. Action on Wall Switch Stop *This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. Wall Switch Response d. P2 Button Channel Options Select A Channel Action on a. Wall Switch a. Press "-" button on the wall switch to Lower select a lower channel. Channel b. Press "+" button on the wall switch to select a higher channel. Wall Switch Response b. Higher Channel Hide Unused Channels Action on a. a. Press and Hold (about 3 sec) "-" and "+" buttons simultaneously until wall switch displays "C" (channel). Wall Switch b. Press "-" or "+" button to select required quantity of channel (between 1 to 15). Wall Switch Response c. Press "Stop" button to confirm selection. The LED will display "o" (OK) once to confirm selection. Action on b. Wall Switch Wall Switch Response Action on c. Wall Switch Wall Switch Response + Lower Higher Channel Channel or Lower Higher Channel Channel Stop ! Essential Settings The steps in factory mode must be completed to ensure proper operation. * AMPCEL and AMPTILT motors DO NOT BEEP. 1. Pair / Unpair Wall Switch a. Press "P1" button (about 2 sec) on Action on a. P1 P1 the motor head until motor jog x1 and Motor P1 beep x1. b. In the next 10 secs, press and hold "Stop" button on the wall switch until motor jog x2 and beep x3. * Repeat the same procedure to unpair wall switch. Motor Response Action on b. Wall Switch Motor Response Jog x1 Beep x1 Stop Jog x2 Beep x3 2. Change Motor Direction (if necessary) Press "Up" or "Down" button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) "Up" and "Down" buttons simultaneously until motor jog x1 and beep x1. Action on Wall Switch *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing "P1" button (about 10 sec) on the motor head until motor jog x3 and beep x3. Motor Response + Up Down Jog x1 Beep x1 3. Setting the Upper and Lower Limits 3.1 Set Upper Limit Action on a. Wall Switch a. Press "Up" button to raise the shade, Up then press "Stop" button when it is in the desired upper limit. Motor Response b. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. b. Up + Stop Jog x2 Beep x3 3.2 Set Lower Limit a. Press "Down" button to lower the shade, then press "Stop" button when it is in the desired lower limit. b. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Wall Switch a. Down Motor Response b. Down + Stop Jog x2 Beep x3 *If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits. Factory Mode Complete User Mode Begins 4. Adjust Limits 4.1 Adjust the Upper Limit a. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Up" button to raise the shade to the desired highest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Wall Switch Motor Response Action on c. Wall Switch Motor Response + Up Stop Jog x1 Beep x1 + Up Stop Jog x2 Beep x3 b. Up 4.2 Adjust the Lower Limit a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on Wall Switch a. + Down Motor Response Jog x1 Action on Wall Switch c. + Down Motor Response Jog x2 Stop Beep x1 Stop Beep x3 b. Down 5. Favorite Position 5.1 Set Favorite Position a. Use "Up" or "Down" button to move the shade to desired Favorite position. b. Press and hold (about 2 sec) one "P2" button on the back of wall switch until motor jog x1 and beep x1. c. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. d. Once more, press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Action on a. Wall Switch Motor Response Action on c. Wall Switch or b. P2 Button Up Down or d. Stop Stop Jog x1 Beep x1 Motor Response Jog x1 Beep x1 Jog x2 Beep x3 5.2 Send Shade to Favorite Position Action on Press and hold (about 2 sec) "Stop" Wall Switch Stop button, motor will move to Favorite position. Shade Response or 5.3 Delete Favorite Position a. Press and hold (about 2 sec) one "P2" button until motor jog and beep x1. b. Press and hold (about 2 sec) "Stop" button until motor jog and beep x1. c. Once more, press and hold (about 2 sec) "Stop" button until motor jog x1 and long beep x1. Action on a. P2 Button b. Wall Switch Motor Response Action on c. Wall Switch Motor Response Jog x1 Beep x1 Stop Jog x1 Beep x1 Stop Jog x1 Beep x1 6. Roller Mode and Sheer Mode 6.1 Roller Shade Mode - continue movement after a short press Default Mode Action on a. Wall Switch a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Motor Response Action on b. Wall Switch Motor Response + Up Down Jog x1 Stop Jog x2 Beep x3 6.2 Sheer Shade Mode - jog movement after a short press (continue movement after a long press) a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on Wall Switch a. Up + Down Motor Response Jog x1 Action on b. Wall Switch Motor Response Stop Jog x1 Beep x1 7. Add or Remove Additional Wall Switch 7.1 Using Current Wall Switch a. On the current wall switch, press and hold (about 2 sec) one "P2" button until motor jog x1 and beep x1. Action on Wall Switch a. Current Wall Switch P2 Button b. Once more, on the current wall switch, press and hold (about 2 sec) one "P2" button until motor jog x1 and beep x1. c. On the New wall switch, press and hold (about 2 sec) one "P2" button until motor jog x2 and beep x3. Motor Response Jog x1 Beep x1 Action on Wall Switch c. New Wall Switch P2 Button b. Current Wall Switch P2 Button Jog x1 Beep x1 *Repeat the same procedure to remove additional wall switch. Motor Response Jog x2 Beep x3 7.2 New Wall Switch Control Follow instructions under the section 1. Pair / Unpair Wall Switch 8. Adjust Motor Speed 8.1 Acceleration Speed Action on a. P2 Button b. Wall Switch a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Up" button until motor jog x1 and beep x1. c. Once more, press "Up" button until motor jog x2 and beep x1. Motor Response Action on c. Wall Switch Jog x1 Beep x1 Up Up Jog x1 Beep x1 Motor Response Jog x2 Beep x1 8.2 Deceleration Speed a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Down" button until motor jog x1 and beep x1. c. Once more, press "Down" button until motor jog x2 and beep x1. Action on Wall Switch a. P2 Button Motor Response Action on c. Wall Switch Jog x1 Beep x1 Down b. Down Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. Motor Response Jog x2 Beep x1
Related FCC IDs:
- 2AU29AMPWSSUV2 - Turnils North America Wall Switch [AMPWSSUV2] Adobe InDesign 15.1 (Macintosh) Adobe PDF Library 15.0