Claymore Basic LED Installation Leaflet A5 W

PDF Viewing Options

Not Your Device? Search For Manuals or Datasheets below:


File Info : application/pdf, 2 Pages, 2.29MB

Document DEVICE REPORTevolt-11277 general eng au manual
INSTRUCTION LEAFLET
CLAYMORE LITE
Remove the product from the box and inspect it for any damage. If you believe the product to be damaged or otherwise unsound, DO NOT install the product. Please pack it back into its box and return it to the place of purchase for replacement. If the product is satisfactory, proceed with the installation.
PREINSTALLATION
Remove end cap by pulling the end cap carefully outward. Slide the wire guard or diffuser slightly, towards the loose end cap before lifting it up and off the batten enclosure.

MOUNTING

B

With cover , A,

detached unscrew two

screws holding the

geartray in place and

remove geartray.

Mount batten onto surface using mounting holes, B, use appropriate fasteners. Wire terminal block, replace geartray and cover.

A Phillips screw

Phillips screw

TERMINAL BLOCK
Wiring schematic for the terminal block used with the Claymore Lite.
L` is the switched active line used to power the normal lighting.
L L
N

REPLACING THE BATTERY
Access the battery by removing the product cover. Disconnect and remove battery. Replace battery as was previously installed. Battery can be connected in one direction only, do not force. Allow a minimum 24 hours charging time before carrying out any discharge tests as per the requirements in AS/NZS 2293.
WARNING
The Ektor Claymore Lite Emergency Luminaire is connected to an unswitched active during normal operating conditions. When disconnected from the mains supply, the Claymore Lite is powered by a LiFePO4 battery operated inverter. Due to this, care
should be taken when replacing the battery.

SAFETY WARNINGS
1. THIS PRODUCT MUST ONLY BE INSTALLED BY A LICENSED ELECTRICIAN.
2. BEFORE COMMENCING INSTALLATION TURN OFF AND ISOLATE THE ELECTRICAL SUPPLY.
3. RISK OF ACCIDENTAL CONTACT WITH LIVE PARTS. DO NOT ENERGISE WITH PRODUCT OPEN OR DISASSEMBLED.
4. SUPPLY VOLTAGES WITHIN PRODUCT. ISOLATE SUPPLY VOLTAGES BEFORE OPENING OR SERVICING.
5. THIS LUMINAIRE IS NOT INTENDED FOR USE IN HIGH-RISK TASK AREA LIGHTING.
6. MAINS SUPPLY AND BATTERY CIRCUIT SEPARATED BY REINFORCED INSULATION.
7. THE ONLY USER SERVICEABLE / REPLACEABLE PART IS THE BATTERY PACK.
8. DO NOT ATTEMPT TO SERVICE OTHER PARTS OF THE FITTING AS THIS WILL VOID THE WARRANTY.
9. AS THE INSTALLER, IT IS YOUR RESPONSIBILITY TO ENSURE YOU COMPLY TO ALL RELEVANT BUILDING AND SAFETY CODES FOR EXAMPLE THE BCA, AS3000. REFER TO APPLICATION STANDARDS FOR THE RELEVANT RULES.
NOTE: CLAYMORE BATTENS ARE NOT SUITABLE FOR DIMMING

Compliance AS/NZS 2293-3:2005+A1:2010

AS/NZS 60598-2-22:2005

AS/NZS CISPR 15:2011

Standards EN 60598-2-22:1998+A1:2003+A2:2008 EN 55015:2006+A1:2007+A2:2009 EN 61547:2009

BATTERY LIFE

To maintain the economic life of this product it is required that the battery be discharged and recharged at least once every

6 months. The battery life can be reduced if the battery is not discharged as per the requirements of AS/NZS 2293 or an equivalent

standard. Increasing the number of duration tests above that as defined in AS/NZS 2293 or an equivalent standard can have a positive effect on the battery performance as long as 12 discharge cycles per year is not exceeded. The recharging device will operate normally after removal of short circuit fault.

1 x LiFePO4 stick battery (1302, 1303)

DIMENSIONS

92mm

124mm

620mm (21W) / 1230mm (42W)

Voltage

~230 V

Frequency

50 Hz

Ambient Temp. 0 - 40°C

Emergency Class. C0:D50, C90:D20 (600mm)

C0:D80, C90:D40 (1200mm)

Class

1

Duration

90 / 120 min

IP Rating

IP20

Mounting Type Surface mounted

Wiring

Terminal Block

Battery Type

LiFePO4 6.4V

Charging Time

16 hours

Charger Type

Variable

Battery supply current 600 mA

ORDERING INFORMATION

CODE
11277 11310

DESCRIPTION
Claymore Lite, 21W LED Emergency, Diffused Wide body batten Claymore Lite, 42W LED Emergency, Diffused Wide body batten

ACCESSORIES AND SPARE PARTS

CODE
01302 01303

DESCRIPTION
1500mAH 6.4V 2 Cell LiFePO4 Battery (600mm models) 3000mAh 6.4V 2 Cell LiFePO4 Battery (1200mm models)

CODE
11110 11820

DESCRIPTION
Claymore Lite, 21W LED Emergency, Wireguard Wide body batten Claymore Lite, 42W LED Emergency, Wireguard Wide body batten

CODE DESCRIPTION
11142 Ledfire Boost Lite Emergency Driver

WARRANTY STATEMENT
Ektor products are distributed in Australia and New Zealand by Evolt Pty Ltd (Evolt). The Australian Consumer Law as well as other Australian laws guarantee certain conditions, warranties and undertakings, and give you other legal rights, in relation to the quality and fitness for purpose of Ektor products sold in Australia. In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. What constitutes a major failure is set out in the Australian Consumer Law. Nothing in this Warranty purports to modify or exclude the conditions, warranties and undertakings, and other legal rights, under the Australian Competition and Consumer Act and other Australian laws. Ektor products are warranted in Australia for a period of 12 months from the date of delivery of the product, provided that the products are properly stored, installed, used and maintained in accordance with the instructions contained within their manual. Products that have been altered in any way or used other than in accordance with their instructions are not covered by this warranty.
This warranty is not transferable and is valid only in the hands of the purchaser of the product. The warranty does not cover Ektor products other than those purchased from Evolt. Proof of purchase must be provided to Evolt with any warranty claim. Evolt recommends that the purchaser attaches their proof of purchase to their product manual. Evolt's total liability under this warranty is limited to the cost of repair or replacement of the faulty product. Evolt may satisfy its obligations under this warranty in full by repair or replacement of a faulty product. This warranty does not apply to consumable items such as lamps or batteries or other items that can be classified as consumable. For the avoidance of any doubt, any and all warranties or conditions which are not guaranteed under the Australian Competition and Consumer Act or the Australian Competition and Consumer Regulations 2010 and which are not expressly included in this Warranty as additional warranties or conditions are excluded. This Warranty does not cover loss or damage caused by wear and tear, misuse, incorrect installation or operation, failure to clean and maintain, incorrect voltage or non-authorised electrical connections, adverse external conditions (such as power surges and dips, acts of God, exposure to heat, corrosion, insect or vermin infestation), use of non-authorised or defective parts or globes, or to items that have been repaired other than by Evolt or a repairer approved by Evolt.
TECHNICAL SUPPORT AND TROUBLESHOOTING
For further assistance in using this product, consult your nearest wholesaler or Evolt Pty Limited.

The leaflet is subject to change without notice

CLAYMORE LITE

Last Updated: 23.December 2016 609857_V1.1

Ph: + 612 9502 1161 Fax: + 612 9502 1154 Email: [email protected] evolt.com.au


Adobe Illustrator CC 2015 (Windows) Adobe PDF library 15.00

Search Any Device: