EMC TEST REPORT
lhf
Test Report
Shenzhen Aishine Electronics Co., LTD AI-IP019 Wi-Fi Home Security Camera 2AI3QAI-IP019 2AI3QAIIP019 ai ip019
Not Your Device? Search For Manuals or Datasheets below:
File Info : application/pdf, 22 Pages, 701.28KB
Document DEVICE REPORTGetApplicationAttachment.html?id=6237007Project No.: ZKT-220823L6014E-2 Page 1 of 22 FCC TEST REPORT FCC ID:2AI3QAI-IP019 Report Number...................................: ZKT-220823L6014E-2 Date of Test..............................................A...u..g....:22, 2022 to Oct. 26, 2022 Date of issue.........................................: Oct. 26, 2022 Total number of pages.......................... 22 Test Result .......................................... : PASS Testing Laboratory............................ : Shenzhen ZKT Technology Co., Ltd. Address ............................................... : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Applicant's name .............................: Shenzhen Aishine Electronics Co., LTD Address ............................................... : Room 512, Floor 5th, XinLong Building,Baishilong, Minzhi, Longhua District, Shenzhen, P.R. China Manufacturer's name ......................: Shenzhen Aishine Electronics Co., LTD Address ............................................... : Room 512, Floor 5th, XinLong Building,Baishilong, Minzhi, Longhua District, Shenzhen, P.R. China Test specification: Standard................................................: FCC CFR Title 47 Part 15 Subpart C Test procedure..................................... : / Non-standard test method ................: N/A Test Report Form No........................ : TRF-EL-107_V0 Test Report Form(s) Originator..... : ZKT Testing Master TRF ........................................ : Dated: 2020-01-06 This device described above has been tested by ZKT, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of ZKT, this document may be altered or revised by ZKT, personal only, and shall be noted in the revision of the document. Product name..................................... : Wi-Fi Home Security Camera Trademark ...........................................: N/A Model/Type reference......................... : AI-IP019, AI-IP027 Ratings.................................................. : Input:100-240V Output:DC 12V 50/60Hz 2.5A 0.6A Testing procedure and testing location: Project No.: ZKT-220823L6014E-2 Page 2 of 22 Testing Laboratory....................................... : Shenzhen ZKT Technology Co., Ltd. Address............................................................ : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China Tested by (name + signature)....................... : Alen He Reviewer (name + signature)....................... : Joe Liu Approved (name + signature)....................... : Lake Xie TABLE OF CONTENTS Project No.: ZKT-220823L6014E-2 Page 3 of 22 1. VERSION .................................................................................................................................. 4 2. TEST SUMMARY ................................................................................................................... 5 2.1 TEST FACILITY ...............................................................................................................................6 2.2 MEASUREMENT UNCERTAINTY ............................................................................................... 6 3. GENERAL INFORMATION .................................................................................................. 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................ 7 3.2 Test mode .........................................................................................................................................7 3.3 Block Diagram of EUT Configuration ........................................................................................... 7 3.4 Test Conditions ................................................................................................................................ 7 3.5 Description Of Support Units (WPT Mode) ................................................................................. 7 3.6 EQUIPMENTS LIST FOR ALL TEST ITEMS ............................................................................. 9 4. CONDUCTED EMISSION TEST ........................................................................................10 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................................... 10 4.1.1 POWER LINE CONDUCTED EMISSION Limits .................................................................. 10 4.1.2 TEST PROCEDURE ..................................................................................................................10 4.1.3 DEVIATION FROM TEST STANDARD ..................................................................................10 4.1.4 TEST SETUP ..............................................................................................................................11 4.1.5 EUT OPERATING CONDITIONS ............................................................................................11 4.1.6 Test Result .................................................................................................................................. 12 5. RADIATED EMISSION MEASUREMENT ....................................................................... 14 5.1 Radiated Emission Limits .............................................................................................................14 5.2 Anechoic Chamber Test Setup Diagram ................................................................................... 15 5.3 Test Procedure .............................................................................................................................. 15 5.4 DEVIATION FROM TEST STANDARD .....................................................................................15 5.5 Test Result ......................................................................................................................................16 6. BANDWIDTH TEST ............................................................................................................. 19 7. ANTENNA REQUIREMENT ............................................................................................... 21 8. TEST SETUP PHOTO ......................................................................................................... 22 9. EUT CONSTRUCTIONAL DETAILS ................................................................................ 22 1. VERSION Report No. ZKT-220823L6014E-2 Version Rev.01 Project No.: ZKT-220823L6014E-2 Page 4 of 22 Description Initial issue of report Approved Oct. 26, 2022 2. TEST SUMMARY Test Item Antenna requirement AC Power Line Conducted Emission Spurious Emission 20dB Bandwidth Project No.: ZKT-220823L6014E-2 Page 5 of 22 Section in CFR 47 15.203 15.207 15.209(a)(f) 15.215 Result Pass Pass Pass Pass NOTE: (1)" N/A" denotes test is not applicable in this Test Report Project No.: ZKT-220823L6014E-2 Page 6 of 22 2.1 TEST FACILITY Shenzhen ZKT Technology Co., Ltd. Add. : 1/F, No. 101, Building B, No. 6, Tangwei Community Industrial Avenue, Fuhai Street, Bao'an District, Shenzhen, China FCC Test Firm Registration Number: 692225 Designation Number: CN1299 IC Registered No.: 27033 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± Uwhere expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2providing a level of confidence of approximately 95 % No. Item 1 3m camber Radiated spurious emission(9KHz-30MHz) 2 3m camber Radiated spurious emission(30MHz-1GHz) 3 3m chamber Radiated spurious emission(1GHz-18GHz) 4 3m chamber Radiated spurious emission(18GHz-40GHz) 5 Conducted Adjacent channel power 6 Conducted output power uncertainty Above 1G 7 Conducted output power uncertainty below 1G 8 humidity uncertainty 9 Temperature uncertainty Uncertainty U=4.5dB U=4.8dB U=4.9dB U=5.0dB U=1.38dB U=1.576dB U=1.28dB U=5.3% U=0.59 Project No.: ZKT-220823L6014E-2 Page 7 of 22 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT Product Name: Model No.: Model Difference: Serial No.: Hardware version: Software version: Operation Frequency: Modulation type: Antenna Type: Power supply: Wi-Fi Home Security Camera AI-IP019, AI-IP027 Only the model names are different for different market requirement. N/A V1.0 V1.0 110.5kHz 250kHz MSK Coil antenna Input:100-240V 50/60Hz 0.6A Output:DC 12V 2.5A WPT rated power is 5W 3.2 Test mode Test Modes: Mode 1 AC/DC Adapter (12V/2.5A) + EUT Wireless charging(5W) Note: All test modes were pre-tested, but we only recorded the worst case in this report. 3.3 Block Diagram of EUT Configuration Conducted Emission DC Mains EUT Radiated Emission DC Line EUT 3.4 Test Conditions Temperature: 2326 Relative Humidity: 5463 % EUT 3.5 Description Of Support Units (WPT Mode) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment E-1 Wi-Fi Home Security Camera E-2 SWITCHING ADAPTOR Mfr/Brand N/A LISTED Model/Type No. AI-IP019 GS120025 Series No. N/A N/A Note EUT EUT A-1 Wireless charging tester YBZ 30W Item Shielded Type Ferrite Core Length Project No.: ZKT-220823L6014E-2 Page 8 of 22 N/A Auxiliary Note Note: (1) (2) (3) The support equipment was authorized by Declaration of Confirmation. For detachable type I/O cable should be specified the length in cm inLengthcolumn. "YES" is means "shielded" "with core"; "NO" is means "unshielded" "without core". 3.6 EQUIPMENTS LIST FOR ALL TEST ITEMS Radiation Test equipment Project No.: ZKT-220823L6014E-2 Page 9 of 22 Item Equipment 1 Spectrum Analyzer (9kHz-26.5GHz) 2 Spectrum Analyzer (1GHz-40GHz) 3 EMI Test Receiver (9kHz-7GHz) 4 Bilog Antenna (30MHz-1500MHz) 5 Horn Antenna (1GHz-18GHz) Manufacturer KEYSIGHT R&S R&S Schwarzbeck Agilent Type No. 9020A FSQ ESCI7 VULB9168 AH-118 Serial No. Last calibration Calibrated until MY55370835 Oct. 18, 2022 Oct. 17, 2023 100363 Oct. 17, 2022 Oct. 16, 2023 101169 Oct. 18, 2022 Oct. 17, 2023 N/A Oct. 17, 2022 Oct. 16, 2023 071145 Oct. 17, 2022 Oct. 16, 2023 6 Loop Antenna TESEQ HLA6121 58357 Oct. 17, 2022 Oct. 16, 2023 7 Amplifier (30-1000MHz) EM Electronics EM330 Amplifier 060747 Oct. 18, 2022 Oct. 17, 2023 8 Amplifier (1GHz-26.5GHz) Agilent 8449B 3008A00315 Oct. 18, 2022 Oct. 17, 2023 9 RF cables1 (9kHz-30MHz) N/A 9kHz-30MHz N/A Oct. 18, 2022 Oct. 17, 2023 10 RF cables2 (30MHz-1GHz) N/A 30MHz-1GHz N/A Oct. 18, 2022 Oct. 17, 2023 11 RF cables3 (1GHz-40GHz) N/A 1GHz-40GHz N/A Oct. 18, 2022 Oct. 17, 2023 12 ESG Signal Generator Agilent E4421B N/A Oct. 22, 2022 Oct. 21, 2023 13 Signal Generator Agilent N5182A N/A Oct. 22, 2022 Oct. 21, 2023 14 Magnetic Field Probe Tester 15 MWRF Power Meter Test system Narda MW ELT-400 MW100-RPCB 0-0344 N/A Oct. 17, 2022 Oct. 16, 2023 Oct. 22, 2022 Oct. 21, 2023 16 D.C. Power Supply LongWei TPR-6405D N/A \ \ 17 EMC Software Frad EZ-EMC Ver.EMC-CON 3A1.1 \ \ 18 RF Software MW MTS8310 V2.0.0.0 \ \ 19 Turntable MF MF-7802BS N/A \ \ 20 Antenna tower MF MF-7802BS N/A \ \ 21 Signal Generator Agilent Conduction Test equipment Item Kind of Equipment Manufacturer 1 LISN R&S N5182A Type No. ENV216 N/A Serial No. 101471 Oct. 22, 2022 Oct. 21, 2023 Last calibration Calibrated until Oct. 22, 2022 Oct. 21, 2023 2 LISN CYBERTEK EM5040A E1850400149 Oct. 22, 2022 Oct. 21, 2023 3 Test Cable N/A C01 N/A Oct. 18, 2022 Oct. 17, 2023 4 Test Cable N/A C02 N/A Oct. 18, 2022 Oct. 17, 2023 5 EMI Test Receiver R&S ESCI3 101393 Oct. 17, 2022 Oct. 16, 2023 6 Absorbing Clamp 7 EMC Software DZ Frad ZN23201 EZ-EMC 15034 Ver.EMC-CON 3A1.1 Oct. 17, 2022 \ Oct. 16, 2023 \ 4. CONDUCTED EMISSION TEST 4.1 CONDUCTED EMISSION MEASUREMENT Project No.: ZKT-220823L6014E-2 Page 10 of 22 Test Requirement: Test Method: Test Frequency Range: Receiver setup: FCC Part15 C Section 15.207 ANSI C63.10:2013 150KHz to 30MHz RBW=9KHz, VBW=30KHz, Sweep time=auto 4.1.1 POWER LINE CONDUCTED EMISSION Limits FREQUENCY (MHz) 0.15 -0.5 0.50 -5.0 5.0 -30.0 Limit (dBuV) Quas-peak Average 66 - 56 * 56 - 46 * 56.00 46.00 60.00 50.00 Standard FCC FCC FCC Note: (1) *Decreases with the logarithm of the frequency. 4.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item EUT Test Photos. 4.1.3 DEVIATION FROM TEST STANDARD No deviation 4.1.4 TEST SETUP Ve rtic a l R e fe re n c e G ro u n d P la n e 40cm EUT Project No.: ZKT-220823L6014E-2 Page 11 of 22 Te s t R e c e iv e r L IS N 80cm H o riz o n ta l R e fe re n c e G ro u n d P la n e N o te : 1 .S u p p o rt u n its w e re c o n n e c te d to s e c o n d L IS N . 2 .B o th o f L IS N s (A M N ) a re 8 0 c m fro m E U T a n d a t le a s t 8 0 cm fro m o th e r u n its a n d o th e r m e ta l p la n e s s u p p o rt. u n its . 4.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data. 4.1.6 Test Result Temperature Pressure Test Voltage 26 101kPa AC 120V/60Hz Project No.: ZKT-220823L6014E-2 Page 12 of 22 Relative Humidity Phase : 54% L Notes: 1.An initial pre-scan was performed on the line and neutral lines with peak detector. 2.Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3.Mesurement Level = Reading level + Correct Factor Temperature Pressure Test Voltage 26 101kPa AC 120V/60Hz Project No.: ZKT-220823L6014E-2 Page 13 of 22 Relative Humidity Phase : 54% N Notes: 1.An initial pre-scan was performed on the line and neutral lines with peak detector. 2.Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3.Mesurement Level = Reading level + Correct Factor Project No.: ZKT-220823L6014E-2 Page 14 of 22 5. RADIATED EMISSION MEASUREMENT Test Requirement: Test Method: Test Frequency Range: Test site: Receiver setup: FCC Part15 C Section 15.209 ANSI C63.10:2013 9kHz to 1GHz Measurement Distance: 3m Frequency Detector RBW VBW Value 9KHz-90KHz peak 9KHz 30KHz peak 9KHz-90KHz Average 9KHz 30KHz Average 90KHz-110KHz Quasi-peak 9KHz 30KHz Quasi-peak 110KHz-490KHz peak 9KHz 30KHz peak 110KHz-490KHz Average 9KHz 30KHz Average 490KHz-30MHz Quasi-peak 9KHz 30KHz Quasi-peak 30MHz-1GHz Quasi-peak 100KHz 300KHz Quasi-peak Above 1GHz Peak Peak 1MHz 1MHz 3MHz 10Hz Peak Average 5.1 Radiated Emission Limits Limits for frequency below 30MHz Frequency Limit (uV/m) 0.009-0.490 0.490-1.705 1.705-30 2400/F(kHz) 24000/F(kHz) 30 Measurement Distance(m) 300 30 30 Limits for frequency Above 30MHz Frequency 30MHz-88MHz 88MHz-216MHz 216MHz-960MHz 960MHz-1GHz Above 1GHz Limit (dBuV/m @3m) 40.00 43.50 46.00 54.00 54.00 74.00 Remark Remark Quasi-peak Value Quasi-peak Value Quasi-peak Value Quasi-peak Value Average Value Peak Value 5.2 Anechoic Chamber Test Setup Diagram ARadiated Emission Test-Up Frequency Below 30MHz Project No.: ZKT-220823L6014E-2 Page 15 of 22 BRadiated Emission Test-Up Frequency 30MHz~1GHz The radiated emission tests were performed in the 3 meters chamber test site, using the setup accordance with the ANSI C63.10-2013. The specification used was the FCC 15.209 and FCC 15.205 limits. 5.3 Test Procedure The EUT is placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can move up and down between 1 to 4 meters to find out the maximum emission level. Broadband antenna (calibrated by dipole antenna) are used as a receiving antenna. Both horizontal and vertical polarization of the antenna are set on measurement. 5.4 DEVIATION FROM TEST STANDARD No deviation 5.5 Test Result Measurement data: Note: Limit dBuV/m @3m = Limit dBuV/m @300m+ 80 Limit dBuV/m @3m = Limit dBuV/m @30m + 40 9 kHz~30 MHz Project No.: ZKT-220823L6014E-2 Page 16 of 22 Frequency (kHz) 24.83 56.72 112.17 125.00* 133.77 685.35 965.71 1228.35 Meter Reading (dBV) 31.63 43.29 38.64 57.13 37.12 32.45 36.84 29.52 Factor (dB) 20.14 20.33 20.55 20.55 20.55 20.64 21.26 22.32 Emission Level (dBV/m) 51.78 63.62 59.19 77.68 57.67 53.09 58.10 51.84 Limits (dBV/m) 119.70 112.53 106.61 105.67 85.08 70.89 67.91 65.82 Note: Pre-scan in the all of mode, the worst case in of was recorded. Factor = antenna factor + cable loss pre-amplifier. Margin = Emission Level- Limit. " * ": Fundamental frequency. Margin (dB) -67.92 -48.91 -47.42 -27.99 -27.41 -17.80 -9.81 -13.98 Detector Type AV AV AV AV AV QP QP QP 30MHz-1GHz Temperature: Pressure: Test Voltage: 26 101 kPa AC 120V/60Hz Project No.: ZKT-220823L6014E-2 Page 17 of 22 Relative Humidity: Polarization: 54% Horizontal Temperature: Pressure: Test Voltage: 26 101kPa AC 120V/60Hz Project No.: ZKT-220823L6014E-2 Page 18 of 22 Relative Humidity: Polarization: 54% Vertical Remarks: 1.Final Level =Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor 2.The emission levels of other frequencies are very lower than the limit and not show in test report. Project No.: ZKT-220823L6014E-2 Page 19 of 22 6. BANDWIDTH TEST 1. Set RBW = 10Hz. 2. Set the video bandwidth (VBW) 3 x RBW. 3. Detector = Peak. 4. Trace mode = max hold. 5. Sweep = auto couple. 6. Allow the trace to stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 20 dB relative to the maximum level measured in the fundamental emission. TEST SETUP Temperature Pressure 26 101kPa Project No.: ZKT-220823L6014E-2 Page 20 of 22 Relative Humidity 54% Frequency (KHz) 221.5 20dB bandwidth 99% bandwidth (Hz) (Hz) 229 211 Result Pass Project No.: ZKT-220823L6014E-2 Page 21 of 22 7. ANTENNA REQUIREMENT Standard requirement: FCC Part15 C Section 15.203 /247(c) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(c) (1)(i) requirement: (i) Systems operating in the 2400-2483.5 MHz band that is used exclusively for fixed. Point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi. 8. TEST SETUP PHOTO Project No.: ZKT-220823L6014E-2 Page 22 of 22 Reference to the appendix I for details. 9. EUT CONSTRUCTIONAL DETAILS Reference to the appendix II for details. END OF REPORT
Related FCC IDs:
- 2AI3QAI-IP019 - Shenzhen Aishine Electronics Co., LTD Wi-Fi Home Security Camera [AI-IP019] WPS 文字