intelbras IVA 5040 AT Articulated active sensors User Guide

IVA 5040 AT Articulated active sensors User Guide

IVA 5040 AT and IVA 5080 AT Articulated active sensors Congratulations, you have just purchased a product with Intelbras quality and safety. The IVA 5040 AT and IVA 5080 AT sensors were developed with the objective of offering an effective infrared barrier, combined with a high flexibility of installation and alignment through its articulation system. Both models have more configurations to meet the demands of installation scenarios, always maintaining the quality of Intelbras products. Read the information carefully for the correct use of both sensor models.

Care and safety

» For installing sensors in perimeters, always follow the sensor layout below:intelbras IVA 5040 AT Articulated active sensors - fig 10 » In order to avoid interference between sensors that may be on the same channel, respect the side protection distance as specified below:intelbras IVA 5040 AT Articulated active sensors - fig 9 » For the IVA 5040 AT sensor, follow the protection distances below:
Distance between TX and RX
20 m 40 m 60m'
Side Protection Distance (DPL) >2 m >3 m >4 m
Vertical Protection Distance (DPV) Maximum stacking of 3 sensors
Side Protection Distance (DPL) Vertical Protection Distance (DPV)
Distance between TX and RX
40 m 80 m 120m'
Side Protection Distance (DPL) >3 m >5 m >7 m
Vertical Protection Distance (DPV) Maximum stacking of 3 sensors
Distance between TX and RX That is, for both IVA 5040 AT and IVA 5080 AT, the side protection distance is always the distance between RX and TX divided by 20 (twenty) plus 1 (one) meter. DPL> Distance between TX and RX + 1 [m] 20 warning 2 In outdoor environments with a high rate of fog or rain, install the sensors at a maximum of 50% of the distance specified for each model, in order to avoid false alarms.

Technical specifications

Model IVA 5040 AT IVA 5080 AT
Number of beams 1 2
Power supply voltage 10 — 24 Vdc / Vac (without polarity)
Consumption current (TX + RX) <65 mA
Frequency channels 3 channels, frequencies 1, 2 and 3
Maximum protection distance External 40 m 80 m
Indoor 60 m /120 m
NA and NF output
Alarm output 2 A @ 24 Vdc
Alarm Time > 2s
Response time 50 ms to 1s, adjustable by trimpot
Detection method Block 1 beam 1 Block 2 simultaneous beams
Alignment indication green LED
Trigger indication red LED
Horizontal Alignment 360°
Vertical Alignment 180°
Solar filter for outdoor environments Yes
Operating temperature -10° to +55°C
IP protection grade IP55
Dimensions (B x W x D) 8 x 24 x 7 cm 8 x 35 x 7 cm
Weight 0.4 KG 0.7 kg

Productintelbras IVA 5040 AT Articulated active sensors - fig 8

  1. Power
  2. Alarm output
  3. Frequency channels
  4. LED On TX
  5. Response time adjustment
  6. LEDs alignment and trigger RX

Installation

1. For security reasons, it is necessary to open the sensors to identify which is the transmitter and which is the receiver. Here's how to open the sensor cabinet and perform the necessary identification:intelbras IVA 5040 AT Articulated active sensors - fig 72. After identification, run the cable as shown in the following image to connect it to the terminal block:intelbras IVA 5040 AT Articulated active sensors - fig 6 3. Secure the sensors in the installation position following the recommendations below: » Do not install the sensor upside down. » Orient yourself by the positioning arrows located on the articulated sensor support.intelbras IVA 5040 AT Articulated active sensors - fig 54. Turn on the power on the receiver and transmitter board (10 ~ 24 Vdc / Vac - no polarity). After that, connect the wires from the alarm output to the zone input of your alarm panel: intelbras IVA 5040 AT Articulated active sensors - fig 4 5. Configure the frequency channel using the FREQ jumper. For the sensor to function correctly, the transmitter (TX) and receiver (RX) must be on the same frequency channel: Frequency channelsintelbras IVA 5040 AT Articulated active sensors - fig 3Position 1 - Frequency channel 1 (factory default) Position 2 - Frequency Channel 2 Position 3 - Frequency Channel 3 6. Perform the Response Time setting. Response time is the time that the infrared barrier must be interrupted to trigger. This setting is only relevant to the receiver:intelbras IVA 5040 AT Articulated active sensors - fig 2 The factory default response time is 50 ms, ie Position 1. To facilitate the association of the response time of the sensor with the interruption speed of the infrared beams, refer to the following table:

Response time  Detection Speed
50ms Intense running
250ms Moderate running
500ms Light running
750ms Walking
1 s Light walk
7. The quality of the sensor alignment is identified by the status of the Green LED on the receiver (RX). To obtain a satisfactory alignment, which will avoid false or unwanted triggering, the alignment must be optimal - only green LED on;
Green LED (RX) Alignment quality  Alarm output (Red LED) Probability of false alarm
Turned Off Beam interrupted ornisahrs' ON Null (unaligned beam)
Slow flashing Poor alignment OFF
Fast flashing Poor Alignment OFF High
Turned On Optimal alignment OFF Lowest
7. After a period of 30 minutes, without the infrared barrier being interrupted, the Alignment Quality indication LED will be automatically turned off for energy saving. The moment the infrared barrier is broken again, this LED will return to the normal Alignment Quality display state. warning 2 Perform walking tests at various points on the barrier to make sure that there is no reflection from the infrared beams on the floor, wall, or reflective objects. If the reflection is found, it will be necessary to change the installation position of the sensor. 8. After making the configuration, tighten the screws for fixing the sensor position on both the receiver and the transmitter, as shown in the following figure:intelbras IVA 5040 AT Articulated active sensors - fig 1 9. To close the sensor follow the steps below:
  1. Place the sealing rubber in the passage of the wires in the TX and RX. (Fig.1)
  2. Place the front cover, attach the upper lock first and then the lower lock. (Fig.2)
  3. Place the screw on the front cover. (Fig.3)
intelbras IVA 5040 AT Articulated active sensors - fig

Troubleshooting

Follow the steps outlined below to troubleshoot your sensor:

  1. Check that the installation distance is within the specified. In environments with a high rate of rain or fog, it is recommended that the installation distance be 50% of the maximum distance for outdoor environments;
  2. Check the installation wiring and that the supply voltage in the TX and RX is between 10 and 24 Vdc / Vac;
  3. Check that both TX and RX are on the same frequency channel, which is selected via the FREQ jumper;
  4. Check that the Response Time setting, which controls the response time from 50ms to 1s, is in accordance with the speed expected to cross the infrared beam;
  5. Redo the alignment procedure;
  6. Perform the detection test and confirm that there are no reflections.
  7. Your infrared barrier sensor will be working!

Warranty term

It is established that this warranty is granted upon the following conditions: Client's name:............................... Client's signature:........................ Invoice number:....................... Date of purchase:......................... Model:....................... Retailer:..................... Serial number:.............................

  1. All the parts, pieces, and components of the product are guaranteed against possible manufacturing defects, which may arise, for the term of 1 (one) year - this being 90 (ninety) days of legal warranty and 9 (nine) months' contractual warranty ­, counting from the date of purchase of the product by the Consumer, as appears in the product purchase bill of sale, which is an integral part of this Term throughout the domestic territory. This contractual warranty includes the free exchange of parts, pieces, and components that have a manufacturing defect, including the expenses with labor used in this repair. If there is no manufacturing defect, but defect(s) arising from misuse, the Consumer shall bear these expenses.
  2. The installation of the product shall be executed in accordance with the Product Manual and/or Installation Guide. If your product requires the installation and configuration by a qualified technician, seek a suitable specialized professional, the costs of these services not being included in the product amount.
  3. Having perceived the defect, the Consumer shall immediately contact the nearest Authorized Service which appears in the report offered by the manufacturer ­ they are the only ones authorized to examine and remedy the defect during the warranty term foreseen herein. If this is not respected, this warranty shall lose its validity, as it shall be characterized as product infringement.
  4. If the Consumer requests home service, it shall contact the nearest Authorized Service to inquire about the technical visit rate. If it is necessary to remove the product, the ensuing expenses, such as those of transportation and insurance of the taking and return of the product, shall be the Consumer's responsibility.
  5. The warranty shall lose its validity totally in the occurrence of any of the following cases: a) if the defect is not one of manufacture, but is caused by the Consumer or by third parties foreign to the manufacturer; b) if the damage to the product arises from accidents, disasters, agents of nature (lightning, floods, landslides, etc.), humidity, the voltage in the electrical network (excess voltage caused by accidents or excessive fluctuations in the network), installation/use in disagreement with the user's manual or arising from natural wear of the parts, pieces and components; c) if the product has undergone effects of a chemical, electromagnetic, electrical or animal (insects, etc.) nature; d) if the serial number of the product has been falsified or erased; e) if the appliance has been infringed.
  6. This warranty does not cover loss of data; therefore, it is advisable that if it is the case of the product, the Consumer makes a backup regularly of the data which appears in the product.
  7. Intelbras is not responsible for the installation of this product, or for possible attempts at fraud and/or sabotage in its products. Maintain the updates of the software and applications used up-to-date, if it is the case, as well as the network protection required for defense against hackers. The equipment is guaranteed against defects in its usual conditions of use, it is important to bear in mind that, as it is electronic equipment, it Is not free of fraud and scams which may interfere with its correct functioning.
  8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Electron collection point (waste management facility to which we are associated). If you have any questions about the reverse logistics process, please contact us at (48) 21060006 or 0800 704 2767 (Monday to Friday 8 am to 8 pm and Saturdays 8 am to 6 pm) or via -mail [email protected].
These being the conditions of this complementary Warranty Term, Intelbras S/A reserves the right to alter the general, technical and esthetic features of its products without prior notice. The manufacturing process of this product is not covered by the requirements of ISO 14001. All the images of this manual are illustrative. intelbras IVA 5040 AT Articulated active sensors - icon

Customer Support: (48) 2106 0006 Forum: forum.intelbras.com.br Support via chat: intelbras.com.br/suporte-Tecnico Support via e-mail: [email protected] Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Imported to Brazil by: Intelbras S/A ­ Indústria de Telecomunicação Eletrônica Brasileira Rodovia SC 281, km 4,5 ­ Sertão do Maruim ­ São José/SC ­ 88122-001 CNPJ 82.901.000/0014-41 ­ www.intelbras.com.br 01.21 Made in China

Documents / Resources

intelbras IVA 5040 AT Articulated active sensors [pdf] User Guide
IVA 5040 AT, IVA 5080 AT, Articulated active sensors

References

Documents - intelbras – IVA 5040 AT,IVA 5080 AT
[pdf] User Manual
Manual do usuario IVA 5040 AT 5080 01 20 backend intelbras sites default files 2020 02 |||
Manual do usurio IVA 5040 AT e IVA 5080 AT Sensores ativos articulados Parabns, voc acaba de adquirir um produto com a qualidade e segurana Intelbras. Os sensores IVA 5040 AT e IVA 5080 AT foram desenvolvidos com o objetivo de oferecer uma barreira infravermelha eficaz, aliada a uma alta flexibili...
lang:pt score:52 filesize: 2.96 M page_count: 2 document date: 2020-02-06
[pdf] User Manual Installation Guide
User manual Intelbras Mar 24 2021 — IVA 5040 AT and 5080 Articulated active sensors Congratulations you have just purchased a product with quality safety Manual ingles 01 21 site backend intelbras sites default files 03 |||
User manual IVA 5040 AT IVA 5080 AT IVA 5040 AT and IVA 5080 AT Articulated active sensors Congratulations, you have just purchased a product with Intelbras quality and safety. The IVA 5040 AT and IVA 5080 AT sensors were developed with the objective of offering an effective infrared barrier, comb...
lang:en score:51 filesize: 2.96 M page_count: 15 document date: 2021-02-11
[pdf] Datasheet
datasheet iva 5040 at 5080 0 backend intelbras sites default files 2019 02 |||
Segurana IVA 5040 AT IVA 5080 AT FCIL INSTALAO 3 TRS CANAIS DE AJUSTE DE FREQUNCIA Sensor de barreira infravermelho ativo SENSOR COM SUPORTE ARTICULADO AMBIENTES INTERNOS E EXTERNOS IVA 5040 AT A L P IVA 5080 AT A Os sensores IVA 5040 AT e IVA 5080 AT oferecem uma barreira infravermelha...
lang:pt score:45 filesize: 1.28 M page_count: 2 document date: 2019-01-18
[pdf] Datasheet
Priscila Vargas IVA 5040 AT 5080 Intelbras Nov 23 2020 — Desenvolvidos com suporte articulado permitem rotacionar e inclinar o sensor para facilitar a instalação alinhamento Características Datasheet backend intelbras sites default files 11 |||
Especificaes tcnicas Cdigo do produto Ambiente de aplicao Nmero de feixes Alcance de proteo externo ... eltricas Alimentao DC Corrente de consumo TX RX Corrente mxima sada de alarme intelbras.com.br IVA 5040 AT/ 5080 AT Sensores de barreira infravermelho ativo Desenvolvidos com suporte articulado, ...
lang:pt score:35 filesize: 483.23 K page_count: 2 document date: 2020-11-17
[pdf]
CAPA Daniel Bertoncini Guia comparativo sensores de barreira 0 backend intelbras sites default files 2020 11 |||
SeSnesnosreosredse daebebraturrreairmaaingfnravtiecromInetlheolbraatisvo Intelbras Proteo perimetral ... anelas, portes ou portas de vidro, instalao sobre muros e complemento de cerca eltrica ou piscinas. IVA 5040 AT 1 feixe infravermelho 3 canais de frequncia para empilhamento de 3 pares Proteo IP 55...
lang:pt score:30 filesize: 1.13 M page_count: 7 document date: 2020-11-30
[pdf]
CAPA Daniel Bertoncini Proteção perimetral em muros e portões Intelbras 2023 01 31 — 1 feixe infravermelho Até 15 m área externa 30 interna IP 55 contra chuva poeira anti UV para instalação em  Guia comparativo sensores de barreira backend intelbras sites default files |||
SeSnesnosreosredse daebebraturrreairmaaingfnravtiecromInetlehlobraatisvo Intelbras Proteo perimetral ... anelas, portes ou portas de vidro, instalao sobre muros e complemento de cerca eltrica ou piscinas. IVA 5040 AT 1 feixe infravermelho 3 canais de frequncia para empilhamento de 3 pares Proteo IP 55...
lang:pt score:30 filesize: 825.76 K page_count: 7 document date: 2023-01-10
[pdf] User Manual Datasheet
Priscila Vargas Ficha técnica IVA 9100 TRI Sensor de Barreira Infravermelho Ativo Intelbras Datasheet 01 20 backend intelbras sites default files 2020 05 |||
Especificaes tcnicas Ambiente de aplicao Nmero de feixes Alcance de proteo externo Alcance de proteo ... 0C a 55C intelbras.com.br Cenrio de aplicao intelbras.com.br Solues integradas Conhea tambm IVA 5080 AT Sensor de barreira com articulador intelbras.com.br IVA 5080 AT Sensor de barreira com ...
lang:pt score:23 filesize: 1.05 M page_count: 4 document date: 2020-05-07
[pdf]
Compre e Ame produtos participantes backend intelbras sites default files 2021 06 |||
PRODUTOS PARTICIPANTES Eletrificadores: Cerca eltrica ELC 5002 High Power 4550002; Cerca eltrica E ... 038; IVA 7100 QUAD 4541039; IVA 7100 HEXA 4541040; IVA 7100 OCTA 4541062; IVA 9100 TRI 4541054; IVA 5040 AT 4541045; IVA 5080 AT 4541046; IVA 3110X 4541015; IVA 3070X 4541014; XAS PORTA DE AO ...
lang:i-klingon score:23 filesize: 654.56 K page_count: 1 document date: 2021-06-21
[pdf]
compre e ame produtos participantes backend intelbras sites default files 2023 03 |||
PRODUTOS PARTICIPANTES Eletrificadores: Cerca eltrica ELC 5002 High Power 4550002; Cerca eltrica E ... 038; IVA 7100 QUAD 4541039; IVA 7100 HEXA 4541040; IVA 7100 OCTA 4541062; IVA 9100 TRI 4541054; IVA 5040 AT 4541045; IVA 5080 AT 4541046; IVA 3110X 4541015; IVA 3070X 4541014; XAS PORTA DE AO ...
lang:i-klingon score:23 filesize: 187.22 K page_count: 1 document date: 2023-02-28

tags: Articulated active sensors, intelbras, IVA 5040 AT, IVA 5080 AT,

Search Any Device: